Laser cutting machine

TRUMPF Loadmaster 1530

Condition: ready for operation (used), Year of construction: 2010, operating hours: 15,043 h, laser power: 3,600 W, travel distance X-axis: 6,500 mm, number of axes: 5, This TRUMPF TruLaser Tube 7000 KT02 was manufactured in 2010. It features a working area of 6500 mm on the X-axis and can handle circular diameters up to 200 mm. Equipped with a CO₂ laser TruFlow 2000 and a laser cutting head with a 155 mm lens, it's ideal for precise tube cutting. Contact us for more information about this machine. • Circular diameter: 200 mm • Reject station: 3 m with brush table • Reject tray • Working Range X Tube Axis: 6500 mm • Outer Circle Diameter: 254 mm (Upgraded from standard 200 mm) • Unloading Station: 3 m with brush table, front unloading • Laser Type: CO2 Laser TruFlow 3600 including LensLine (Surcharge upgrade from standard TruFlow 2000) • Control: Sinumerik 840D, Teleservice • Standard Software/Features: NitroLine, FocusLine, SprintLine, Laser power control, Programmable cutting gas pressure, Program re-entry, Automatic shutdown, Workspace lighting, Laser logbook function, Laser cooling unit • Laser: CO₂ laser TruFlow 2000 • Laser cooling unit • Cutting Head: Lens cutting head with 155 mm focal length, ControlLine • Control unit: 84D • Connectivity/data transfer: RJ-45 network connection, USB connection; network connection incl. installation • Safety: CE marking, Multi-beam light barriers, Compact dust extractor 1500 Nm³/h, Protective cabin with Makrolon panels • Ambient Operating Temperature: Up to 43°C • Installation Type: Special machine installation setup Additional equipment • Accessories: • Spare parts case for cutting heads • 1 x remote control kit • Clamping jaw set Ø 16 / 200 mm Djdjx D I H Depfx Afxekt • U-shaped guide rails for reject station with ID = 200 mm • Automation: • Loading Unit: LoadMaster Tube 6.5 m with bundle support, 2 grippers, 254 mm outer circle diameter capacity, low-scratch design for 6m, swiveling conveyor line, additional gripper D=254 mm • Options for LoadMaster Tube 6 m: • Circular diameter 250 mm • Shorter belt support • Swivelable conveyor section • Additional gripper Ø 200 mm • Additional gripper Ø 250 mm • Special equipment: • Flexible reject station 4.5 m (prototype) instead of reject station 3 m, without brush table • Special installation for flexible reject station • LoadMaster (series version 103) • Installation 100 mm higher (use of wire mesh container possible), decision upon acceptance • Services: • Installation, commissioning, training

Condition: new, Ostas Profile Ring Bending Machine OPK 125 Dedpfjxrd Rnsx Afxekt Technical Specifications: • Tool holder, shaft: 120 mm • Tool: 390 mm • Working speed: 2-7.5 m/min • Motor: 15 kW • Dimensions (L-W-H): 2000 x 1700 x 1950 mm • Weight: 4850 kg • 3 rollers are driven separately by a hydraulic motor and planetary gearbox • Hardened standard rolls • Hardened and ground tool holder, shaft • Mobile control panel • Horizontal and vertical working position • Hydraulic side supports • Digital displays (2 pcs.) • In accordance with CE standard

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 SHATS OUTPUT SIZE 90 MM SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT Dkjdpewkrr Tefx Afxet SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: excellent (used), Year of construction: 2018, operating hours: 34,000 h, functionality: fully functional, Great opportunity! Like-new Salvagnini S4 / P4 from the first owner, built in 2018! The machine is in perfect, like-new condition and ready for immediate use! The system has been regularly serviced by Salvagnini, and the machine is covered by a maintenance contract. Technical data and Salvagnini internal number: Punching machine/shear with rotating station S4Xe.30 consisting of: Conveyor belt TAC30.L2000 Corner turning device DA30 Punching machine S4Xe.30 Punch head H3 Oil-dynamic hydraulic unit HU22E Control and management of the SiX system Dksdpezh I Iiefx Afxjt Right-angle shear CS5S Turning device DF Lower cylinder EI09 Embossing unit BU30 Double rotating punch P2R3132 Double rotating punch P2R3334 Threading roll unit ME35 Device for automatic application of self-adhesive labels LBC (label printer) Portal robot MC30 Conveyor with brushes CTS30 Shear lift table TCV3015 Water-air cooling unit R81E Tools (detailed list available on request) P4Xe-3125 Swivel bending machine including roller and turning station consisting of: Shear lift table TCV3015.CT.RPC Feeder-destacker device PCD3015 Turning device RIP3015 Bending center P4Xe-3125 Upper bending die LS Lower bending die LI Programmable clamping device U1 Standard clamping foot NS Control and management of the SiX system Work surface with balls SFE Device for cleaning and lubricating the bending dies PSE Asymmetrical control for auxiliary bending tools for positive bends CLA-A CLA tool set with "swan neck profile" UCE1500G38 Asymmetrical control for auxiliary bending tools for negative bends CLA-N-A CLA tool set with "swan neck profile" for negative bends UCE1500NG38 Device for V-notch RSU.UR-4 Swiveling device for auxiliary tools T Option for cutting and dispensing profiles CUT.SPC31 T-tool for 90° bends UTZ2 Delivery device/buffer for panels SAP34.POS The system has a hinged belt conveyor for central disposal of the sheet metal sections. These are then conveyed to tipping containers via a swan neck conveyor. Sorting according to stainless steel, aluminum, and black sheet metal is fully automatic. A weighing and level measuring device is integrated and reports the level via the control system. The machine can be inspected and tested by arrangement. Additional videos and detailed images of the system are available on request!

Condition: excellent (used), functionality: fully functional, Year of construction: 2010, laser power: 4,000 W, X working area max.: 3050 mm Y working area max.: 1550 mm Control: Rexroth IndraMotion MTX Laser power: 4,000 watts Standard equipment: Machine - Sturdy, easily accessible C-frame - Coordinate guidance for high-precision machining - Linear tool changer with 21 tool stations and 4 clamps - Maintenance-free three-phase drive motors - Repositioning device with programmable hold-down - Foot switch for closing clamps - 2 good parts containers - Automatic shutoff Laser station - TruFlow laser - High-frequency excitation - Cooling unit - TASC 3 laser controller - Enclosed beam guidance - Beam tube ventilation with compressed air - Programmable cutting gas pressure - Laser cutting head with 170 mm focal length - Universal quick-change cutting head device UTI with bus connection - LensLine - FocusLine - ControlLine - NitroLine - SprintLine - ContourLine - FlyLine - PlasmaLine - High-speed cutting - Additional Xp and Yp axes - Ejector cylinder for laser parts - Fast flap for laser parts 500 x 500 mm - Liftable laser cutting support - Slag cone detection - Laser logbook function Punching station - Electro-hydraulic punching head - Rotatable mono-tool holder - Tool length compensation - Programmable hold-down with adjustable force - Stroke counter for punches - Spray lubrication for punches - Punch slug extraction - Warp detection - Flap for punched parts 500 x 500 mm - Fill level monitoring in the punching console Control Djdpfxoy Saqgo Afxokt - Open control system based on Bosch Rexroth IntraMotion MTX - Operating panel with 15" TFT touchscreen - Program management and 80 GB storage capacity - Diagnostic function with laser logbook - Integrated technology data - Teleservice Data transfer - Network connection RJ45 and USB interface Safety - CE marking - Multi-beam light barriers - Monitoring system for, among others, gas pressure, temperature, cooling water - Hydraulic quick shut-off - Protection against stray radiation - Compact extraction unit - TruFlow 4000 - Vibration-dampened installation - Thread forming function - MultiTool function - Chip conveyor with tilting container - Active die - Ejector for small parts - Brush tables with loading aid - Marking function - Repositioning cylinder - Warp detection

Condition: ready for operation (used), Year of construction: 2018, The UniTower is suitable to store bars or extrusions as well as sheet metal, plates, Euro pallets or boxes. Pallets: Dimensions X/Y/Z: 3000mm/1500mm/90mm, payload per pallet: 1500kg, number of storage spaces: 86 pieces. Payload: 15kN, occupancy rate: 90%. Total dimensions without stations X/Y/Z: approx. 9000mm/6000mm/5800mm. On-site inspection is possible. Dsdjxv Au Tepfx Afxekt

Year of construction: 2009, condition: ready for operation (used), A CNC CO2 laser cutting machine Amada with automated storage system LKI is available. 1) Laser power: 4kW (4000W), travel X/Y/Z: 3100mm/1550mm/100mm, max. table load: 920kg, max. material thickness steel/stainless steel/aluminum: 20mm/12mm/10mm, laser system dimensions X/Y/Z: approx. 10000mm/4300mm/2100mm, weight: approx. 11000kg. 2) Pallets: 8, cutting pallets: 2, raw material: 2/3, unloading: 4/3, max. unloading height: 2200mm, max. material dimensions X/Y: 3050mm/1525mm, min. sheet dimensions: 2000mm/1000mm, height: 5400mm. Documentation available. On-site inspection is possible. Djdpfx Ajv Rp S Sofxskt

Condition: good (used), Year of construction: 2014, functionality: fully functional, Sheet width: 3000 mm Sheet length: 1500 mm Sheet thickness: 8 mm Workpiece weight: 200 kg Punching force max.: 220 kN Total power requirement: 9.5 kW Space requirement approx.: 7395 x 6540 x 2072 mm Equipment: Punch head: - Hydraulic single-tool chuck with 360° rotation - Manually adjustable clamping force - Programmable clamp (active/passive/re-positioning) - Spray lubrication for punch - Stroke counter for punch - Level monitoring for threading and tool lubrication Control system: - Open control system based on Sinumerik 840 D - 12" TFT color display - Teleservice via internet - Automatic shutdown Data transfer: - USB interface - RJ-45 network connection Safety: - CE marking - Dual light curtains - Rapid shutdown of hydraulics - Bulge detection Programming: - TruTops Punch via network access 1 x MultiTool function 1 x MultiShear function 1 x Thread forming function 1 x Deburring and rolling technology 1 x SoftPunch function 4 x individually openable clamping jaws 4 x height-adjustable clamping jaws 1 x Re-positioning cylinder 1 x Sensor for stripper (included in rest material-free processing) - GripMaster - Rest material grippers with sensor technology Dkodpfx Afjy Sak Texot - Shear lift table 400 mm - Tilting rest material pallet 3000 x 1500 mm - SheetMaster - Operating hours: 65,000 h

Condition: used, functionality: fully functional, Year of construction: 2019, operating hours: 14,669 h, Trumpf TruPunch 1000, 2019 X Working area max.: 2500 mm Y Working area max.: 1250 mm Operating hours: 14,669 hours Machine - C-frame - Coordinate guidance - Linear magazine with 20 positions for clamping blocks and tools - Hydraulic clamping blocks (2 pieces + 1 option) - Drives with maintenance-free three-phase motors - Post-processing unit with programmable positioning device - 1st stop pin (inside right) - Transfer chute Punch head - Electro-hydraulic punch head - Rotatable mono-tool holder - Programmable positioning device position - Tool length compensation - Spray lubrication for punch - Punch slug extraction - Forming function Control - TRUMPF control based on Rexroth IndraMotion MTX - Control panel with 15" TFT color screen - Integrated technology data - Teleservice interface via internet Dsdpfezmgi Njx Afxekt - Automatic shut-down - Program management - Production plan Data transfer - USB interface - RJ45 network connection Safety - CE marking - Multi-beam light barriers - Rapid shut-down of drives Extended standard equipment - Brush tables - Chip conveyor + chip container - Additional clamping block - Sheet thickness detection - Vibration-damped installation - Programmable support table - Sensor for transfer chute - Wireless operation point Extended punching technology: Multitool Thread forming

Condition: good (used), functionality: fully functional, Year of construction: 1992, control type: manual, degree of automation: manual, actuation type: hydraulic, shaft diameter: 100 mm, roller diameter: 300 mm, bending radius (max.): 500 mm, bending radius (min.): 500 mm, rotational speed (min.): 5 rpm, rotational speed (max.): 5 rpm, pipe diameter (max.): 115 mm, tube wall thickness (max.): 3 mm, overall weight: 2,700 kg, total length: 150 mm, total width: 150 mm, total height: 150 mm, power: 7.35 kW (9.99 HP), input voltage: 380 V, operating pressure: 200 bar, year of last overhaul: 2026, Equipment: documentation/manual, emergency stop, hardened rollers, Profile bending machine model PP100 Output shafts 100 mm fully hydraulic operated lower shafts motion independent pyramid pinch -all the 3 shafts driven with gear unit and hydraulic motor -lateral correctors left/right for guiding and align the profile, -Set of rollers complete with extra rollers to seat and bend the various shape of profiles. -7 set of rollers for pipe bending from 1,5” to 4,5” inch ( see photo in enclosed ) -Centralized control panel electric with digital position readout -Safety & emergency installation -voltage 3ph 380/50 -10 Hp Djdpfoywhamsx Afxekt -capacity chart in enclosed