Used Baler for sale (238)

Condition: used, Speed-Tech Equipment horizontal cardboard baler, bales are approx. 1200 lbs., 6' long x 36" wide x approx. 28" tall, 3 phase, in working condition, winning bidder responsible for proper removal. Gsdpfexd D Nzsx Ahnsbn

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced Gbsdpfjzbxwiex Ahnon • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: good (used), Year of construction: 2014, Large waste compactor / cardboard press, Höma, – used: Price at location: only €18,950 (net) for self-dismantling! Manufacturer: Höma Type: PB4000 Year of manufacture: 2014 Machine number: 140409 Weight: 1,200 kg Pressing force: not specified, but we estimate 40 tons. The press has a second discharge chute. Price includes a small crane with trolley. 30 kW Condition: good Available: from Q4/2026 Location: Hamburg For an additional charge, a conveyor system for empty cardboard boxes, over 100 m long, is available! Photos at the end of the advertisement! Gbodpfszbyf Ijx Ahnjn

Condition: ready for operation (used), Year of construction: 2009, Well-maintained PRESTO HPK 50 BSK automatic horizontal baler in fully operational condition. The machine has been in continuous industrial use and has been regularly serviced and professionally maintained throughout its lifetime. It was recently dismantled from operation due to plant modifications and is ready for transport and immediate recommissioning. Suitable for baling: Cardboard (OCC) Paper Mixed recyclables Plastic films PET bottles Packaging waste The HPK 50 BSK is a compact and reliable industrial baler designed for medium to high throughput operations. Its large feed opening allows efficient loading by conveyor, wheel loader or excavator. The fully automatic wire tying system ensures consistent bale quality and low operating costs. The PRESTO HPK series is well known throughout Europe for durability, simple maintenance and reliable operation. Pressing force: 50 t Motor power: 22 kW Power requirement: 400 V / 80 A Feed opening: 1,250 x 1,050 mm Bale dimensions: 1,100 x 700 mm Bale weight: up to approx. 500 kg depending on material Cycle time: approx. 22 sec Throughput: up to 5–10 t/h depending on material density Fully automatic 4-wire tying Machine dimensions: approx. 6,820 x 1,950 x 2,160 mm Gbodpfxezcdrnj Ahnsn Machine weight: approx. 8.75 t

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Model: 155 VL Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Godpjzc Hhxefx Ahnsbn Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg Gsdpsxalyyefx Ahnebn - Year: 1983 - Documentation available: No - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Gbjdpfx Ahjy S Ru Aonen Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Gbodpfxsy S Rtle Ahnon Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Gedpoy S Rqwefx Ahnobn Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: like new (used), Year of construction: 2014, functionality: fully functional, Cameras for Premier Tech – suitable for high-speed compression balers. Used very little, practically new. Gbjdpfszckp Hjx Ahnsn Can be used for bags measuring 465x365x1320 mm.

Condition: used, functionality: limited functionality, Year of construction: 2013, Gallignani baling press Gbjdpfx Aozb I Nhohnsn Subject to prior sale – all information is provided without warranty. We cannot guarantee the accuracy or completeness of the information provided here. Any warranty and/or liability is excluded. Deviations from the description above cannot be ruled out. We would like to point out that the subject of the purchase agreement to be concluded will be exclusively the motor vehicle in its actual condition.

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Gjdpfx Asv Amw Nehnjbn Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Gbedezaqymjpfx Ahnon Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Godpfx Ahoy R Nnfonobn Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: excellent (used), Year of construction: 2018, Baler, Bramidan B20 - second-hand - : Price ex location: 7.750.-€ (net) Manufacturer: Bramidan Type: Vertical raw material balers B20 Year of construction: 2018 Bale weight Cardboard (kg) 200-250 Plastic film (kg) 250-300 Pressing force 20 t Bale size WxDxH (mm) 1200 x 800 x 800 Filling opening WxH (mm) 1200 x 480 Power supply 3x400V 50Hz 16A Motor (kW) 4.0 Cycle time average (s) 36 / 21 Dimensions WxDxH (mm) 1775 x 1030 x 2790 Transport height: 2.58m Weight (kg) 1250 Stroke (mm) 750 Number of tie-downs 4 Type of strapping Strap Finished bale light Yes Bale ejection Automatic The classic among raw material balers The B20 is versatile and is used everywhere. The recyclable materials must be "dry & soft". Particularly suitable for raw materials such as cardboard, paper, cardboard packaging (PPK) and film. Stackable bales, up to 900 kg per pallet The bales are stacked 2 or 3 high on one; enormous space saving. Simple bale strapping Gedpfsrl I Ivsx Ahnebn Automatic bale ejection Short cycle time thanks to high speed Strap rollers mounted on the front allow installation directly on the wall Pallet-sized bales that can be stored outdoors under cover 3xx230x-440 4kW Amps: 25/16 dB 62-64 Condition: good - very good Available: immediately Location: 09116 Chemnitz

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Gbodpfx Ajvq Rtkjhnon Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Gbedoym Uxtjpfx Ahnjn Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No Godpfx Aeyrtcushnjbn - CE marking present: Yes - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 1996, pressing force: 30 t, input voltage: 380 V, bale weight: 600 kg, type of input current: AC, overall weight: 3,000 kg, Manufacture: Philadelphia Tramrail Model: HT30036 Vintage: 1996 Gedpfom Amk Nsx Ahnobn 400V/45A, 3 phases, 15kW 180 bar system pressure 206 bar maximum system pressure Made of heavy-duty structural steel Average cycle time of 53 seconds Dimensions: 1980 x 1050 x 3860mm Advance height: 1400mm Baling chamber: 1600 x 760

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Gbodpfx Asy Uimvshnon Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feeding opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2008 Gjdpfx Asy Uil Ejhnsbn Press force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm x 65 cm Please contact us for a video or more information.

Condition: used, Waste compactor, baler, waste baler, chamber baler, Orwak Compactor 3110, used machine Manufacturer: ORWAK (Sävsjö, Sweden) Type: Compactor 3110 Gsdpfx Ahey S Ui Djnebn Serial No: 105441 Product No: 4903110-00 Overall dimension: 865 x 680 x 2050 mm -press force: 4t -production date: 2011-11 -voltage: 230 V -frequency: 50 Hz -power: 1.1 kW -current: 8.9 A -weight: 340 kg

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Gbedpfx Ahera Nrmjnen Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Condition: used, Year of construction: 2005, Chamber press - baling press Austropressen APV 300, used 🧰 Product features • Manufacturer: Austropressen • Model: APV 300 • Condition: Used item, see photos • Color: turquoise • Year of manufacture: 2005 • Dimensions: approx. 1620 x 1260 x 2920 mm • Own weight: 1650 kg • Pressing force: 300 kN • Cycle time: 45 seconds • Power: 5.5 kW • Voltage: 400 V (12.5 A) • Bale weight: 300 - 400 kg 💰 Price: €7,200 net excl. VAT • Quantity discount: on request • Shipping: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by appointment Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock Gbjdjxvy N Uopfx Ahnen (Technical data, details, and prices subject to change and error, as well as prior sale! See our GTC, all prices excl. VAT ex stock.)

Condition: used, Year of construction: 2019, Chamber Press - Baling Press - Raw Material Press Bramidan X30 AD, used 🧰 Product Features • Manufacturer: Bramidan • Model: X30 AD • Condition: Used, see photos • Color: Orange • Year of manufacture: 2019 • Dimensions: approx. 1760 x 1255 x 2295 mm • Net weight: 1650 kg • Press force: 300 kN • Cycle time: 25 seconds • Power: 4 kW Gsdpfx Ajxvyn Dehnsbn • Voltage: 3 x 230 - 440 V / 50/60 Hz • Noise level: 59 - 60 dB • Bale weight: Plastic up to 425 kg, cardboard up to 350 kg 💰 Price € 8,900 net excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: possible at any time by prior arrangement Constantly over 5,000 linear meters of pallet racking from various manufacturers in stock (Subject to changes and errors in technical data, information and prices as well as prior sale! See our terms and conditions; all prices excl. VAT ex stock.)