Used Hole Number for sale (29,755)

Condition: excellent (used), Year of construction: 2009, drilling depth: 350 mm, workpiece weight (max.): 1,600 kg, table load: 1,600 kg, Deep hole drilling machine Mollart - LD8 - 150 Pellet Die Number of Spindles 8 Gun Drilling Diameter Range 1.5mm-10mm (Per Spindle) Maximum Drilling Depth 150mm Drill Spindle Stroke 350mm Pellet Die Diameter 500mm-1550mm B-Axis Accuracy +/- 6 Arc Seconds Y-Axis Vertical Travel 400mm Gun Drill Speed Range 0-14,000 RPM Max. drill Ø steel 1.5 - 10 mm Drilling depth 350 mm Table load 1600 Speeds / ranges 14000 Rpm Dimensions (Estimate) Length 4500 mm Width 4500 mm Height 2300 mm Weight 12000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Nedoyilgdopfx Ahpjlf

Condition: good (used), gear diameter: 508 mm, total height: 1,780 mm, total length: 2,990 mm, total width: 2,200 mm, MODEL 610 GLEASON GEAR ROUGHER/FINISHER Equipped with: Hydraulic Workholding Pendant Control Chip Conveyor Index Plate Geneva Cam Change Gears Hydraulic System Coolant System Manuals Specifications: Maximum Gear Pitch Diameter: 20" Cutter Diameters: 9", 10.5", 12",14",16", 18" Whole Depth: 1.250" Root Angle: 60 to 80 deg. Face Width: 3.0" Extreme Ratio (Minimum): 2.25 to 1 Number of Teeth: 20 to 75 Diameter of Taper Hole at Large End: 3-27/64" Njdjrtrykepfx Ahpolf Cutter Speeds (Per Minute) for Roughing: 15.6' to 87.7' Feeds (Seconds Per Tooth) for Roughing: 3 to 35 Cutter speeds (Per Minute) for Finishing: 6.8' to 20.5' Feeds (Seconds Per Tooth) for Finishing: 3 to 9 Floor Space: 118" x 86.5" x 70" H Weight: 17,500 lbs.

Condition: ready for operation (used), Fanuc A06B-0853-B100 / B-65152E AC spindle motor, serial number: C987J1757 – has a hole in the shaft (see photos), used, in good condition, 100% functional, scope of delivery as shown in the photos. Nljdpfezu El Sex Ahpsf

Condition: used, Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring machine, T-slot plate, pallet changer Nlodpfxeiaqngj Ahpjf -Width: 1250mm -Length: 1595mm - Height: 47mm - Holes: M16 grid 50 x 50 mm -Drilling: 22 mm grid 450 x 400 mm -Plate: without straight edge -Number: 1 piece available -Weight: 700kg

Condition: used, Year of construction: 2020, functionality: fully functional, table length: 6,000 mm, table width: 2,540 mm, sheet thickness steel (max.): 50 mm, cutting length (max.): 6,000 mm, cutting width (max.): 2,540 mm, FICEP KRONOS KR25SP - CNC GANTRY PLASMA CUTTING SYSTEM FOR STEEL PLATES | YEAR 2020 The Ficep Kronos KR25SP is an automatic CNC gantry system for high-definition plasma cutting of steel plates, designed for steel construction and sheet metal fabrication shops that need precise, repeatable and cost-efficient parts directly from plate. With a maximum plate size of 2,540 x 6,000 mm and a plasma cutting thickness of up to 50 mm, it covers a broad range of parts in a single pass. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. The machine is fully functional and can be put into production immediately. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The KR25SP cuts steel plates fully automatically according to CNC program in gantry design. Using Hypertherm plasma technology including True-Hole technology, it produces contour-accurate cut parts and hole patterns at high cut quality - ideal for gusset plates, end plates, base plates and connection components in steel construction. The robust grid cutting table is prepared for connection to an extraction system; a network remote-diagnosis interface supports maintenance and support. TECHNICAL DATA - Manufacturer: Ficep S.p.A., Italy | Model: Kronos KR25SP (KRONOS SP series) - Machine type: Automatic CNC gantry plasma cutting system for steel plates - Year of manufacture: 2020 | Serial number: 36499 - Condition: used, refurbished by certified technician - Maximum plate size (W x L): 2,540 x 6,000 mm - Max. plasma cutting thickness: 50 mm - Plasma straight-cut torch: 1 | Plasma unit: Hypertherm XPR300 - Hypertherm True-Hole technology: available - CNC control and drives: Fanuc (to be confirmed on the machine during inspection) - Remote diagnostics: available (network connection) - Cutting table: robust grid construction, prepared for extraction system - Extraction and filter system: optionally available Further details (machine weight, connected load, footprint, cutting speed) are available on request. SCOPE OF DELIVERY - 1 x Ficep Kronos KR25SP gantry system (year 2020) - 1 x plasma straight-cut torch (Hypertherm XPR300) - Grid cutting table with extraction preparation - CNC control and drives - Remote-diagnosis interface (network) LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border - short transport distance from the entire DACH region. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. Nsdpfx Ajv Iaqyehpelf ABOUT ASM Arendsen Steel Machinery (ASM) is your specialist for refurbished Ficep steel construction machinery. We supply inspected, ready-to-operate systems for steel construction and sheet metal fabrication. Further Ficep systems on request. CONTACT / INQUIRY Arrange a viewing | Price on request | Request a callback. Sale exclusively to commercial customers (B2B).

Condition: ready for operation (used), Year of construction: 2012, This is a side seam wicket bag machine Lemo Intermat 850 STN-CP Knoter, production type: wicket bags for bread, chicken, diapers, toilet paper, hygiene products and other types of wicket bags, number of lanes: single lane / lane wicket, processable materials: LDPE, HDPE, PP and recycled extracts, sealing width (bag length): 120-450mm, draw length (bag width): 200-850mm, gripper arm length: 600mm, max. linear speed: 65m/min, output capacity: 140 knot bags/min, max. number of bags per stack: 250, drive system: PLC-controlled, operator interface (terminal), print mark control, servo motor drive, nip feed rollers, sealing bars. Attachments and accessories: bottom gusset (only bottom gusset included), handle unit, longitudinal sealer, pre-sealer, angle sealer, cross sealer, handle punch, photo cell for printed film, automatic one-step conveyor (index conveyor), handle hole punch, G-gusset unit, V-gusset station, web guiding system 1800mm, anti-static bars, automatic labeling system. Machine is in good condition. Njdpfxjw U T T Ej Ahpslf

Condition: excellent (used), Year of construction: 1996, functionality: fully functional, machine/vehicle number: 25734, wheel diameter: 700 mm, gear diameter: 1,000 mm, wheel width: 152 mm, workpiece spindle speed (max.): 67 rpm, feed length X-axis: 610 mm, feed length Y-axis: 610 mm, feed length Z-axis: 725 mm, pivoting range: 95 °, spindle bore: 203 mm, travel distance X-axis: 610 mm, travel distance Z-axis: 725 mm, Equipment: rotational speed infinitely variable, Equipped with: Fanuc 150MB Control Hydraulic Chucking Work Spindle Large Bore Work Spindle #80 Taper Stock Divider Helical Motion Modified Roll Hansen Coolant Chiller & Filtration Coolant Tank & Pumps Chip Conveyor Chip Hopper Reven Mist Collector Hydraulic System Transformer Cutter Bolt Work Light Operator Platform Hand Tools Documentation Specifications: Extreme Ratio: Face Milling: 10:1, Face Hobbing: 10:1 Full Depth: Maximum: Face Milling:1.25" (31.75mm), Face Hobbing: 0.93" (23.50mm) Face Width: Maximum: Face Milling:6.00" (152.00mm),Face Hobbing: 3.00" (76.20mm) Range of Tooth Numbers: 1-300 Inclusive Gear Pitch Diameter, Maximum: 1000 mm (39.37") Cutter Size, Maximum: 18" (diameter) Face Milling Cutter Size, Maximum: 350 mm (radius) Face Hobbing Root Angle Range (B-Axis) 5 deg.to 90 deg., Face Hobbing:5 deg. to 90 deg. Machine Center to Work Spindle Face:9.00"Fixed, 229mm (Fixed) A-Work Spindle: 0 to 67 RPM, 0 to 333 RPM B-Swinging Base: 0 to 30 deg./sec, N/A C-Cutter: 0 to 500 deg., Same X-Horizontal: +/-305mm (+/-12") Y-Vertical: +/-305 mm (+/-12") Z-Sliding Base: -25/+700mm (-1/+28") B-Root Angle: -5 Degree/+90 Degree Diameter of Taper Hole at Large End: 8" (#80 Taper) to 6" (#60 Taper) Taper Per Foot:3/4", Same Depth of Taper Front:6", 152.40 mm Depth of Bore: 678 mm (26.7") Diameter of Taper Bore: 140 mm (5.5") Diameter Through Spindle of Hole:7.125", 180.98 mm MACHINE DIMENSIONS: Length x Width:233"x 209", 5920 mm x 5310 mm Height: 129", 3280 mm Weight: 65,000 lbs., 29,484 kg Nlsdoxaqa Sspfx Ahpsf

Condition: used, Year of construction: 1993, Control Sinumerik 805 turning speeds 45 - 6000 U/min Solid drill diameter / 0 weight of the machine ca. 20 t Type of machine: deep hole drilling machine Model / Type: TB 2 15 30001KT Year of construction: 1993 Manufacturer: hole Machine number: 221-3000-2093 Machine weight: approx. 20,000 kg Machine footprint: Width = approx. 3800mm Length = approx. 13500mm Height = approx. 3100mm Drilling length: approx. 3500mm Drilling capacity: drill 45mm / drill out 80mm Spindle speed range: 45 - 6000 rpm Control: Siemens Sinumerik 805 Hamül – coordinate table Nljdpfx Asvvx Hijhpjf Type: KT 8.5 – 10.10 Clamping surface: approx. 1100 mm x 980 mm Travel: Y - axis: approx. 800mm Traverse path X - axis: approx. 500mm 7 pieces clamping - T - grooves: 18 mm Special equipment: 1 piece Fibroplan NC - rotary indexing table Type: NC 1.05 Permissible transport load in horizontal use 2500 kg With manual chuck Forkardt F 630 The NC rotary indexing table can be adjusted manually in the longitudinal and transverse directions relative to the clamping table and is clamped hydraulically. 1 piece chips - centrifuge Type: VZ5A from CEPA Drum capacity: 80 liters Loading weight max. 100 kg Drum - Ø: 600 mm Speed: 1000 rpm 1 additional pump for large drill Ø 1 piece Bosch radial piston pump no.: Suitable for lip drills (internal cooling, chips run outwards) Suitable for BTA drills with screw-on heads (internal cooling, chips run inwards)

Condition: new, overall weight: 140 kg, total height: 1,010 mm, total length: 660 mm, total width: 700 mm, empty load weight: 120 kg, New, originally packaged Ricoh RB5030 Ring Binder. Nlodpfxswra Dae Ahpef New price of €33,340 euros Suitable for the Ricoh Pro 8310 / 8320, among others Paper size: A4 / 8.5 x 11'' LEF Paper Weight: 64 - 256 g/m2 Number of holes: 21 Stack capacity: 11 sets Ring Bind capacity: 2 to 100 pages Ring Supply: Black or white, up to 50 or 100 pages

Condition: refurbished (used), Year of construction: 2000, functionality: fully functional, drilling depth: 600 mm, rotational speed (max.): 6,000 rpm, center height: 250 mm, controller model: SIEMENS Sinumerik 840 D, workpiece diameter (max.): 25 mm, No reserve price – guaranteed sale to the highest bidder! The machine has been completely overhauled! TECHNICAL DETAILS Working depth: 600 mm Working diameter: 4 – 25 mm Number of spindles: 2 Centre height: 250 mm Centre distance: 203.2 mm Speed range: 1,000 – 6,000 rpm Feed rate: 0 – 300 mm/min Rapid traverse: 6,000 mm/min MACHINE DETAILS Control system: SIEMENS Sinumerik 840 D (Retrofit) Drilling system: Single-lip deep hole drilling Main drive: 2 x 5.5 kW EQUIPMENT - Single functions for machine setup - Semi-automatic operation for manual loading - Robust spindle carriage - Machine monitoring with spindle speed display - Table plate in special cast design - Safety guard with sliding door - Machine bed with hardened and ground linear guides - Internal coolant supply through drilling spindle - Electrical equipment according to IEC standards - Separate control cabinet with safety devices Nljdpfx Ahjxpvbtspef - Control panel in working area

Condition: ready for operation (used), functionality: fully functional, Gear hobbing machine: Largest gear module: 8 mm Largest gear diameter: 500 mm Largest rim width: 100 mm Spindle stroke: 150 mm Largest spindle stroke: 125 mm Diameter of the product spindle flange or worktable: 560 mm Base hole in the table or product spindle flange: 110 mm Number of double strokes: 18 Range of double stroke changes: 55-560/min Peripheral feed rate range: 6-590 mm/min Radial feed rate range: 0.02–0.2 mm/s Distance between the lower plane, floor, and table work surface: 920 mm Largest distance between the table surface and the tool spindle surface: 270 mm Smallest distance between the table surface and the tool spindle surface: 120 mm Largest distance between the table axis and the tool axis: 355 mm Smallest distance between the table axis and the tool axis: 0 mm Limb and vernier value for setting the product and tool distance: 0.01 mm Automatic table retraction Table movement relative to the tool axis: 355 mm Rapid table movement speed: 1.5 m/min High-speed table rotation: 4.5 rpm Drilling depth: 25 mm Tool offset at idle speed: 0.5 mm Amount of static comparison for tool offset at an angle: ± 20 mm Nsdpfxezhwa Ue Ahpjlf Number of motors: 6 Main drive motor power: 4/4.5/7.5 kW Hydraulic drive motor: 2.2 kW Table rotation acceleration motor power: 0.75 kW Coolant pump motor power: 0.6 kW Lubrication pump motor power: 0.25 kW Power supply for the peripheral motor: 2.4 kW Dimensions (L x W x H): 1975 x 1690 x 2510 mm Power supply: 3x 380 V; 50 Hz Machine weight: 7500 kg

Condition: used, Year of construction: 2019, - Magazine loading system - Clamping table for frame parts - 3 horizontal, longitudinal drilling units from the rear - 4 vertical drilling units from above 1 Drilling machine Manufacturer: KOCH Type: BL 2500 NC select line - used - Year of manufacture: 2019 Workpiece dimensions Workpiece length 150 - 2500 mm Workpiece width 20 - 300 mm Workpiece thickness 10 - 50 mm Material: Solid wood Magazine loading system 1 with workpiece return. Workpiece insertion via 2 parallel-controlled servomotors. The number of workpieces in the magazine depends on the workpiece weight. Manual workpiece insertion Clamping table for frame parts 1 By inserting 3 support segments into the longitudinal drilling units, workpieces can be inserted manually and clamped with clamping cylinders and templates. This also allows for special workpiece dimensions. Work cycle triggering via 2 manual controls on the swappable control panel. 3 horizontal, longitudinal drilling units from the rear Construction width 160 mm Drilling motor 2 kW Longitudinal adjustment (X) with LCD display Vertical adjustment (Z) With dust extraction 4 vertical drilling units from above (supported on one side in a linear guide) Adjustable over the entire working width (X), reading LCD display. Adjustable in working depth (Y), reading LCD display One vertical clamping cylinder mounted directly on the unit Counterpieces for through-holes are available as an option. Drilling motor 1.5 kW at 50 Hz Drilling stroke 50 mm Speed 2,800 rpm Total drill length 70 mm With 4 rotary indexing heads with quick adjustment (for vertical drilling units) with fixed stops at 0 and 90 degrees Positioning control KOCH NUMERIC Basic 1 Positioning control with Beckhoff C6920 industrial PC Intel Celeron 2.2GHz CPU 2.5 320GB HDD 1x RS232, 2x USB, 1x Ethernet available 15-inch touch panel Operating system Windows 7: English Nsdpfx Ahozuynhopelf User interface in English Input of all machine commands via the touch panel Software is prepared for an online connection. The configuration of the online connection (network) and commissioning are carried out by the customer or their software company. USB port on the PC 4 x Dynamic NC axis (with bearing control) for Z axes Connection data 1 Electrical connection 400 V, 50 Hz, 3 phases Voltage fluctuations max. + 6 % to - 10 % If protected by an RCD (residual current device) on the customer's side, an all-current sensitive (R CCB, Type B) RCD with a rated residual current of /= 300 mA must be used. Air connection 7 bar Dust extraction air velocity min. 30 m/s Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: good (used), Year of construction: 2013, total length: 3,990 mm, total height: 2,500 mm, total width: 2,280 mm, overall weight: 8,500 kg, INGERSOLL CM SYSTEMS AOHD AGILE OIL HOLE DRILL Equipped with: Siemens 840D Control (2) Drill Heads 20-Tool Rack HSK 50A Taper (2) 7" 3-Jaw Chucks (2) Tailstocks (2) Steady Rests Chip Auger Chip Conveyor Mist Collector Hydraulic System Q R 2 Lube System Air Compressor Specifications: Maximum Length: 1050 mm (41.3") Minimum Length: 180.0 mm (7.1") Maximum Stroke: 250.00 mm Maximum Main Journal Diameter: 115.0 mm (4.5") Maximum Pin Journal Diameter: 100.00 mm (3.9") Maximum Swing Diameter: 250.0 mm (9.84") X-Axis Travel: 1450 mm (57.1") Y-Axis Travel: 150 mm (5.9")W/HSK 50 Z-Axis Travel: 305.0 mm (12.0") A-Axis Travel: 360 Degree Nodortrx Repfx Ahpelf B-Axis Travel: 90 Degree Feed Rate (Z): 1 m/min Maxim (40"/min max) Position Accuracy of X,Y,Z Axes: .010 mm (.00039") Position Accuracy of A & B Axes: .03 Degree Position Repeatability of X,Y,Z Axes: .005 mm (.0002") Position Repeatability of A & B Axes: .005 Degree Spindle Power: 5.5 kW (7.5 hp) Spindle Speed: 0-6,900 RPM Tool Adaption: HSK 50E or A Tool Storage (ATC): 20 Total - 10 Per Spindle W/HSK 50 Lubrication - Slides & Ball Screws: Automatic Central Lubricator Approximate Floor Space (LxWxH): 4.0 x 2.3 x 2.5 m (13.1 x 7.5 x 8.2 Ft) Approximate Machine Weight: 8,500 kg (18,740 #)

Condition: used, Year of construction: 1997, machine/vehicle number: 150069, Press capacity: 125 ton Ram stroke adjustable: 30 - 120 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 450 mm Free frontal opening L-R: 1.290 mm Free lateral opening F-B: 450 mm Table surface area : 1.250 x 800 mm Slide area: 1.250 x 650 mm Hole in table: 1.050 x 260 mm Number of strokes: 30 - 220 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 3.800 mm Dimensions L x W x H: 3.500 x 2.200 x 3.800 mm Weight of machine approx.: 21,5 ton Standard configuration electrical overload protectionpneumatic clutch2 connecting rodsPLC Siemens S5 Extended machine accessories Strip shear AI 40max. shear force 10tSheet thickness max. 4 mmSheet width max. 400 mmCross section 600 mm2 Nledpfxsuqdhwe Ahpof Automation Kaiser Feeder KWV 400max. sheet width 400 mm

Condition: used, Year of construction: 2006, Solid drill diameter / mm bore depth / mm number of spindles / Froriep CNC deep hole drilling machine – the prefabrication specialist Year of manufacture: 2006 Control system: Siemens Sinumerik 840D Max. drilling depth: 8,850 mm Workpiece diameter: 150 – 900 mm Speed range: 1 – 300 rpm Feed rate: 0.5 – 4,500 mm/min Drive power: 129 kW Swing diameter over bed: 1,000 mm Clamping diameter faceplate: 900 mm Weight: approx. 47,000 kg Ideal for precise pre-drilling of deep holes – including faceplate, steering ring Nledoxgu R Iopfx Ahpjf

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Index Plate Geneva Cam Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Nodpfx Asxdfazehpslf Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: used, total length: 1,400 mm, total height: 2,050 mm, total width: 1,400 mm, Empty weight: 500 kg Price: On request Nsdpfx Aswh Naiohpolf Granulator Dreher S26/26 VS Machine No. K 8329 Built in 1982 Engine 5.5kW Speed 1440 Rpm. 2 fixed blades 3 rotating blades (need to be replaced) Funnel opening: 360x240 mm Interchangeable strainer Sieve holes 6mm - Documentation available: No - CE certificate present: No - Main motor power [kW]: 5.5 - Rotation speed [rpm]: 1440 - Opening width [mm]: 360 - Opening length [mm]: 240 - Sieve perforation [mm]: 6 - Number of rotating knives [pcs.]: 3 - Number of fixed knives [pcs.]: 2 - Transport dimensions: 1400mm x 1400mm x 2050mm (l x w x h) - Transport weight [kg]: 500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2006, Solid drill diameter / mm bore depth / mm number of spindles / 2-machine package: Froriep deep hole drilling machine & Irle finishing machine Perfectly matched duo for deep hole drilling and precise finishing of large workpieces A specialised machine package is available for sale – two perfectly matched systems for the complete machining of long, heavy workpieces with the highest demands on precision and efficiency. MACHINE 1 Froriep CNC deep hole drilling machine – the prefabrication specialist Year of manufacture: 2006 Control system: Siemens Sinumerik 840D Max. drilling depth: 8,850 mm Workpiece diameter: 150 – 900 mm Speed range: 1 – 300 rpm Feed rate: 0.5 – 4,500 mm/min Drive power: 129 kW Swing diameter over bed: 1,000 mm Clamping diameter faceplate: 900 mm Weight: approx. 47,000 kg Ideal for precise pre-drilling of deep holes – including faceplate, steering ring MACHINE 2 Irle machine – high-precision finishing Power: 129 kW Control: Siemens NC control Nlsdpfxjuddime Ahpef Speed range: 2 – 300 rpm (stepless) Feed: 3 – 4,500 mm/min (in steps) Centre distance: 11,000 mm Swing diameter over bed: 1,250 mm Clamping range of steady rests: 150 – 1,100 mm Workpiece length: up to 11,000 mm Workpiece weight: up to 10 tonnes Max. outer diameter: 850 mm With up to 50,000 Nm torque, perfect for smooth drilling, honing and demanding finishing processes. Your advantages at a glance - Complete solution from a single source – from pre-drilling to finishing - Large workpieces up to 11 metres and 10 tonnes in weight - High process reliability thanks to perfect machine synchronisation - Ready for immediate use, well maintained and from ongoing operation - Ideal for mechanical engineering, energy, oil & gas, hydraulics and large parts manufacturing

Condition: ready for operation (used), Year of construction: 2011, operating hours: 12,946 h, functionality: fully functional, travel distance X-axis: 935 mm, travel distance Y-axis: 850 mm, travel distance Z-axis: 650 mm, controller model: Heidenhain iTNC 530 HSCI, spindle speed (max.): 15,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel in X-axis: 935 mm Travel in Y-axis: 850 mm Travel in Z-axis: 650 mm Number of axes: 3 Table length: 1,200 mm Table width: 850 mm Max. table load: 2,000 kg Spindle taper: SK 40 / HSK-A63 Spindle speed: 15,000 rpm Tool changer: 30-position Nlsdpfx Aozwn Etjhpef Rapid traverse: 40 m/min Feed rate: 40,000 mm/min MACHINE DETAILS Control system: Heidenhain iTNC 530 HSCI Operating hours: 36,420 h Spindle hours: 12,946 h EQUIPMENT Chip conveyor

Year of construction: 2015, condition: new, Unused (NOS) Sulzer industrial agitator for tank mixing, with SCABA-S agitator head, stainless steel shaft, and SEW geared motor. The unit is from 2015 and is in new, unused condition. Manufacturer: Sulzer Pumps Sweden AB Type: SVVT-40 / 40SVV35T-M1 Year of manufacture: 2015 Condition: NOS (unused, stock item) Application: Tank agitator / Industrial agitator Agitator type: SCABA-S Motor power: 1.10 kW Process power consumption: 0.80 kW Mains frequency: 50 Hz Motor speed (n1): 1,500 rpm Output speed (n2): 244 rpm Gearbox manufacturer: SEW-Eurodrive Gearbox type: KAF47 Gearbox design: Helical-bevel gearbox Gear ratio: i = 5.81 Motor adapter: 24FF165 Gearbox mounting position: M1 Flange: Special flange Flange diameter: 340 mm Bolt circle: 295 mm Mounting holes: 8 × Ø22 mm Shaft length: 500 mm Shaft design: Solid shaft Shaft material: Material 1.4462 (LDX Duplex stainless steel) Number of agitator elements: 1 Propeller type: 3SHP1 Propeller diameter: 475 mm Nledpfszlcfwex Ahpef Propeller material (hub): Material 1.4462 (LDX) Blade thickness: 4 mm Blade attachment: welded Direction of rotation: right (clockwise) Axial force: 244 N Torque: 43 Nm Bending moment: 74 Nm Minimum stiffness of tank mounting: 250,517 Nm/rad Tank medium (design): Vegetable oil Design temperature of medium: 65 °C Paint color: RAL 5017 Y-ring: present Flushing connection: no flushing

Condition: ready for operation (used), Year of construction: 2005, X-axis: 505mm, y-axis: 405mm, z-axis: 405mm, number of M8 threaded holes: 9, max. workpiece height: 545mm, max. table load: 180kg, accuracy: ISO 10360-2, resolution: 0.1µm, guide system: air bearings on all axes, traverse speed CNC mode: 8-300mm/s (max. 520mm/s), joystick rapid traverse: max. 80mm/s, slow: 0.05mm/s, measuring speed: 1-8mm/s (CNC), acceleration: 0.13g (max. 0.23g), measuring table material: granite, table dimensions: 638x860mm, compressed air consumption: approx. 50l/min at 0.4MPa, length: 1122mm, width: 1082mm, height: 2185mm, weight (incl. table and control): 515kg. An on-site inspection is possible. Njdpfxoy Duq Ee Ahpjlf

Condition: used, Year of construction: 1974, operating hours: 10,000 h, functionality: fully functional, machine/vehicle number: 8002/6410, drilling depth: 1,000 mm, drill diameter: 30 mm, type of input current: three-phase, spindle motor power: 21 W, table length: 1,000 mm, input voltage: 550 V, mount diameter: 160 mm, number of spindles: 1, drilling capacity: 1,000 mm, quill diameter: 30 mm, Equipment: rotational speed infinitely variable, Deep hole drilling machine for up to 1000 mm and 30 mm diameter, used for drilling aluminium, regularly serviced, includes a significant quantity of drills. Machine is fully operational and in continuous use. Siemens control, Simatic PANEL, documentation available. Nodpfx Ahsx Ehg Tspelf

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, number of spindles: 2, spindle speed (max.): 4,500 rpm, turning length: 145 mm, turning diameter: 240 mm, travel distance X-axis: 130 mm, travel distance Z-axis: 145 mm, Horizontal, twin-spindle CNC lathe with 2 turrets in two working areas and 2 loading portals! The machine underwent an overhaul in 2023! TECHNICAL DETAILS Turning diameter max.: 240 mm Turning length max.: 145 mm Travel X-axis: 130 mm Travel Z-axis: 145 mm Distance between spindles: 340 mm Rapid traverse X/Z-axis: 24 m/min Guidance X-axis: Roller linear guide Guidance Z-axis: Round guide, 145 mm Number of spindles: 2 Spindle drive power: 11 / 7.5 kW Max. spindle speed: 4,500 rpm Torque: 93 Nm Spindle nose: JIS A2-5 Chuck size: 210 mm (8 inches) Number of turrets: 2 Turret type: BT turret Tool positions per turret: 8 Shank size for external turning tools: 20 × 20 mm Max. shank diameter for boring bars: 40 mm Nlodpfx Aheztxlcspof MACHINE DETAILS Control: Fanuc 32i-B Working areas: 2 Power connection: 30 kVA Dimensions & Weight Footprint: 4,500 × 2,440 mm Overall height with loader: 2,550 mm Weight: 4,400 kg Loading portal GT Twin with two independent portals Dual gripper for raw and finished parts Turning station Control unit with cable Max. workpiece diameter: 120 mm Max. workpiece length: 80 mm Max. workpiece weight: 3 kg EQUIPMENT Stack magazine, on the left side Parts conveyor belt, on the right side Chip conveyor, on the rear side Coolant tank Coolant supply through both spindles for flushing the clamping devices Various tool holders Various clamping devices Documentation and wiring diagrams

Condition: good (used), Clamping plate, plate field, welding table, welding table, plate boring machine, surface plate, Nljdpfxeckk T Tj Ahpjf -with: holes -Width: 1000 mm -Length: 1000 mm -External height: 150 mm, panel thickness 100 mm -Number: 7x plates available -Price: per piece -Weight: 720 kg/piece

Condition: used, mileage: 45,000 km, power: 390 kW (530.25 HP), first registration: 03/2025, fuel type: diesel, overall weight: 18,000 kg, color: grey, gearing type: automatic, Equipment: soot filter, Vehicle number: 1424766004 1st owner, accident-free, full service history, non-smoker ---- Additional Features * We also offer financing, leasing, and rental options! * LA1 & LA2 7146 MOONSTONE GREY METALLIC * LZ2 FULL PAINT FINISH * C1W WHEELBASE 3700 MM * W9Z WEIGHT VARIANT 18.0 T (7.5/11.5) * M3E ENGINE OM471, R6, 12.8 L, 390 KW (530 HP), 2600 NM * M4X ENGINE VERSION EURO VI, E * M8B AIR INTAKE, BEHIND CAB, MOUNTED * M7K RADIATOR BLIND * M7T CONTROLLED WATER PUMP * M5V HIGH PERFORMANCE ENGINE BRAKE * M6M TWO-STAGE, CONSUMPTION-OPTIMIZED AIR COMPRESSOR * G5A SINGLE-PLATE CLUTCH * G2E TRANSMISSION G 281-12/14.93-1.0 * N6Z TRANSMISSION OIL COOLING * G5G MERCEDES POWERSHIFT 3 * G5L POWERSHIFT ADVANCED * G0K DRIVE PROGRAM ECONOMY/POWER * N2E NA MB 131-2C, PUMP * Z5M PTO, SINGLE * Z5S PTO PUMP, BELOW FRAME UPPER EDGE * A1Z FRONT AXLE, CRANKED DESIGN * A1D FRONT AXLE 8.0 T * A2E REAR AXLE, RING GEAR 440, HYPOID, 13.0 T * A3D REAR AXLE WITH ACTIVE LUBRICATION, NON-REGULATED * A5G AXLE RATIO I = 2.412 * A1A FRONT AXLE AIR SUSPENSION * J3Z AXLE LOAD MEASURING SYSTEM * R5E ALUMINIUM RIMS 11.75 X 22.5, FRONT, DURA-BRIGHT, ALCOA * R2Y ALUMINIUM RIMS 9.00 X 22.5, DURA-BRIGHT, ALCOA * R0L CUSTOMER-SPECIFIED TYRES FRONT * R0Z WHEEL NUT COVERS * S1Y TYRE PRESSURE MONITORING * A1 W48KBA 75 2 X 385/65 R 22.5 TL HIGHWAY RR STEERING? K? * A2 F38LCB 75 4 X 315/70 R 22.5 TL HIGHWAY RR DRIVE? L? * CZW STEP PLATE ABOVE FRAME, EXTENDED * C5P BOLTED FRAME * C0G REAR FRAME OVERHANG 1050 MM * C6G STEERING, SERVOTWIN * C6I POWER STEERING PUMP, CONTROLLED * C7T REAR INTEGRAL END * K0T MAIN TANK, LEFT * K1N TANK 570 L, LEFT, 650 X 700 X 1450 MM, ALUMINIUM * K3W ADBLUE TANK 75 L, LEFT * K5M LOCKABLE TANKS * K5S PROTECTIVE CAP FOR ADBLUE DOSING SYSTEM * Z4O NARROW TANK CROSS-SECTION * Z4R HIGH TANK CROSS-SECTION * K8D EXHAUST SYSTEM, OUTLET RIGHT SIDE EXTERNALLY, HORIZONTAL * U2G EXHAUST BOX * C8B REAR AXLE MUDGUARD, 2550 MM VEHICLE WIDTH * C8H 3-PIECE MUDGUARD, WITH EC SPLASH PROTECTION * C8I SPLASH PROTECTION (EC), FRONT * C7F FRONT UNDER-RUN PROTECTION (ECE), ALUMINIUM * C8Y UNDERBODY PANELING, AERODYNAMIC * F7A BUMPER, CORNERS PLASTIC * F7C BUMPER, CENTRE PART WITH TOWING EYELETS * C8Z SIDE SKIRTS, AERODYNAMIC * Q4Z FIFTH WHEEL, LOW MAINTENANCE, GREASED LOCK * Q6J FIFTH WHEEL COMPACT, JOST JSK 40K * Q6G FIFTH WHEEL, WITHOUT MOUNTING PLATE * Q6Z FIFTH WHEEL ANGLE, WITH HOLE GRID * Q4L FIFTH WHEEL HEIGHT, H = 190 MM * H2C FIFTH WHEEL OFFSET +600 MM * Q0W FIFTH WHEEL FROM FACTORY * B2A DISC BRAKE, FRONT AND REAR AXLE * B1B ELECTRONIC BRAKING SYSTEM WITH ABS AND ASR * B1F HEATING, ELECTRONIC AIR SUPPLY UNIT * B1H ELECTRONIC AIR SUPPLY & CONTROL, MEDIUM * B4A CONDENSATE MONITORING FOR AIR SYSTEM * B4L COMPRESSED AIR TANKS, ALUMINIUM, COMPLETE * B5D TRAILER STABILITY ASSIST (TSA) Nsdewflwlepfx Ahpjlf * B5J BRAKE AND ELECTRICAL CONNECTIONS, LOW * B2X PARKING BRAKE, ELECTRONIC * B3K SECONDARY OIL RETARDER * F1J L-CAB GIGASPACE, 2.50 M, FLAT FLOOR * F1R L-CAB * F2A FLOOR VERSION, FLAT FLOOR * F2H CAB WIDTH 2.50 M * F2P CAB, 765 MM MOUNTING HEIGHT * F2X GIGASPACE * F4H CAB REAR WALL, WITHOUT WINDOW * F3C CAB SUSPENSION, COMFORT, AIR SUSPENDED * F3W CAB TILTING DEVICE, MECHANICAL-HYDRAULIC * F6D TINTED WINDSCREEN WITH SUN STRIP * F8V LIGHT SENSOR * F8W RAIN SENSOR * D8M ELECTRIC SLIDING/TILTING SUNROOF, GLASS DESIGN * F4X EXTERNAL STORAGE BOX, LEFT * F4Y EXTERNAL STORAGE BOX,