Used Platen for sale (571)

Condition: good (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 211886, Plastic Injection Moulding Machine | Arburg Allrounder 630 S 2500-170 Clamping force [kN]: 2,500 Number of components: 3 Clamping platen width [mm]: 900 Clamping platen height [mm]: 900 Clear tie bar spacing horizontal [mm]: 630 Clear tie bar spacing vertical [mm]: 630 Centre ring diameter [mm]: 160 Min. mould height [mm]: 400 Max. mould height [mm]: 700 Maximum opening stroke [mm]: 600 Maximum ejector stroke [mm]: 225 Thread [M]: 24 Multi turntable type: Rotary table Gisdjyf Ha Hspfx Abrjn Rotary table diameter [mm]: 900 Rotary table thread [M]: 20 Max. mould weight [kg]: 2,500 Max. mould weight, moving side [kg]: 2,500 Screw diameter [mm]: EE1:30, EE2:25, EE3:25 Max. shot weight [g] PS: EE1:83, EE2:59, EE3:58 Aggregate configuration: EE1: horizontal, EE2: vertical, EE3: L-position Equipment: 2-core pull, robot Inspection possible at any time by appointment. Free loaded on truck (Butzbach). #Tags: ARBURG | Multi 3K | 630S

Condition: ready for operation (used), Year of construction: 2001, operating hours: 98,780 h, clamping force: 2,000 kN, overall weight: 12,200 kg, controller manufacturer: ENGEL, controller model: CC100, This 3-axis Engel ES650H/200W-200HL-2F was manufactured in 2001. It features a clamping force of 2000 kN, a mold opening stroke of 700 mm, and a tie-bar distance of 920 x 750 mm. Equipped with dual injection units, screw diameters of 40 mm and 25 mm, and a rotary table control. Consider the opportunity to buy this Engel ES650H/200W-200HL-2F hydraulic injection moulding machine. Contact us for more information about this machine. • Clamping unit • Mold weight (WZ): 1500 kg • Total moving weight: 3000 kg • Minimum mold height: 550 mm • Mold opening stroke: 700 mm • Tie-bar distance (H × V): 920 × 750 mm • Platen size: 1250 mm Godpfx Aboyf H Nnjrjin • Ejector stroke: 150 mm • Ejector force: 61 kN • Centering ring diameter A-side: 110 mm • Centering ring diameter B-side: 90 mm • Mold locking system: Hydraulic / Pneumatic • Core pull control: Yes • Number of cores: 4 (A-side) • Rotary table control: Yes • Index plate control: Yes • Injection unit 1 (Main) – Type 650H • Max. shot volume: 200 cm³ • Stroke volume: 251 cm³ • Screw diameter: 40 mm • L/D ratio: 20 • Screw speed: 290 rpm • Injection pressure: 1930 bar • Injection rate: 142 g/s • Shot weight (PS): 216 g • Plasticizing rate: 26 g/s • Nozzle orifice: 15 mm • Pump motor: 30 / 12.3 kW • Injection unit 2 (Secondary) – Type 200W • Max. shot volume: 140 cm³ • Stroke volume: 69 cm³ • Screw diameter: 25 mm • L/D ratio: 24 • Screw speed: 480 rpm • Injection pressure: 2000 bar • Injection rate: 104 g/s • Shot weight (PS): 60 g • Plasticizing rate: 12 g/s • Nozzle orifice: 15 mm • Pump motor: ~6.8 kW • Machine axes travel • X-axis (injection unit): 500 mm • Y-axis (rotary table / mold carrier): 1000 mm • Z-axis (clamping unit): 1400 mm • Equipment and options (machine-integrated) • SPC / Process control: Yes • Pressure interface: Yes • Second injection barrel: Yes • Mold monitoring: No • Cavity pressure sensor: p-θ-t-θ (Priam) • Hot runner control: 16 zones • Filter dryer: No • Special programs: Yes • Special option: GealanXcomp • Automation: No • Condition • Well-maintained and serviced Additional equipment • Engel Linear Take-out Robot ERC 23/1-E (included)

Condition: ready for operation (used), Year of construction: 2000, operating hours: 63,929 h, clamping force: 2,000 kN, controller manufacturer: ENGEL, controller model: CC 200 (CC200), This 3-axis Engel ES650H/200W-200HL-2F was manufactured in 2000. It features a clamping force of 2000 kN, a tie-bar distance of 920 × 750 mm, and a screw diameter of 50 mm. Equipped with dual injection units, hydraulic locking system, and a rotary table control, it ensures precise and efficient operation. If you are looking to get high-quality injection molding capabilities, consider the Engel ES650H/200W-200HL-2F machine we have for sale. Contact us for more information. • Condition: Well-maintained and serviced • Clamping unit: • Mold weight: 1500 kg • Total weight: 3000 kg • Tie-bar distance (H × V): 920 × 750 mm • Platen size: 1150 mm • Opening stroke: 700 mm • Daylight (opening): 700 mm • Min. mold height: 450 mm • Max. mold height: not specified • Ejector stroke: 150 mm • Ejector force: 61 kN Gsdsyf Htyspfx Abroin • Return force: not specified • Centering diameter (A side): 110 mm • Centering diameter (B side): 90 mm • Locking system: Hydraulic / Pneumatic • No. of cores: 4 • Rotary table control: Yes • Core pull control: Yes • Index plate control: Yes • Injection unit 1 (650H): • Max. shot volume: 200 cm³ • Stroke volume: 392 cm³ • Screw diameter: 50 mm • L/D ratio: 20 • Screw speed: 290 rpm • Injection pressure: 1240 bar • Injection speed: 120 g/s • Plasticizing rate: 41 g/s • Nozzle orifice: 15 mm • Pump installed: 30 / 12.3 kW • Injection unit 2 (200W): • Max. shot volume: 140 cm³ • Stroke volume: 69 cm³ • Screw diameter: 25 mm • L/D ratio: 24 • Screw speed: 480 rpm • Injection pressure: 2000 bar • Injection speed: 60 g/s • Plasticizing rate: 12 g/s • Nozzle orifice: 15 mm • Pump installed: ~6.8 kW • Controls and functions: • SPC (Statistical Process Control): Yes • Pressure interface: Yes • 2nd injection barrel: Yes • Mold monitoring: No • Special programs: Yes Additional equipment • Take-out device (robot): ERC 23/1-E • Travels: X = 500 mm, Z = 1400 mm • Max. mold dimensions (Y-axis): 1000 mm • Hot runner control: 18 zones • WZ sensor system: p–z–t–σ (Kistler) • Additional equipment: GealanXcomp • Automation cell: No • Filter dryer: No

Condition: like new (used), Year of construction: 2018, clamping force: 2,300 kN, Equipment: documentation/manual, Toshiba EC230SXII – 230 ton Injection unit i8 – Screw 50 mm CLAMPING UNIT Clamping force: 2250 kN (230 t) Tie bar spacing (H×V): 610 × 560 mm Platen size (H×V): 880 × 830 mm Moving platen stroke: 550 mm Max daylight: 1230 mm Mold height min–max: 250–680 mm Ejector force: 49 kN (5.0 t) Ejector stroke: 130 mm INJECTION UNIT – 50 mm Screw diameter: 50 mm Shot volume: 392 cm³ Shot weight PS: 361 g Shot weight PE: 286 g Max injection pressure: 200 MPa Max holding pressure: 200 MPa INJECTION SPEED / RATE STD speed: 250 mm/s STD rate: 490 cm³/s Godpfx Aoyhpi Ajbrjin HIGH DUTY speed: 160 mm/s HIGH DUTY rate: 314 cm³/s HIGH SPEED speed: 350 mm/s HIGH SPEED rate: 687 cm³/s PLASTICIZING Plasticizing capacity PS: 160 kg/h Screw speed: 255 rpm Screw torque: 1421 Nm Nozzle contact force: 29.4 kN (3.0 t) ELECTRICAL Main breaker STD: 125 A Main breaker HIGH DUTY: 125 A Main breaker HIGH SPEED: 175 A Transformer: 75 kVA Heater capacity: 15.2–16 kW DIMENSIONS & WEIGHT Length: 6.4 m Width: 1.7 m Height: 2.0 m Weight: 9.9 t

Condition: ready for operation (used), Year of construction: 2003, operating hours: 28,646 h, clamping force: 2,500 kN, screw diameter: 60 mm, injection weight: 810 g, This DEMAG El Exis S250/630-2300 was manufactured in 2003. It features a clamping force of 2500 kN, a screw diameter of 60 mm, and a shot volume of 891 cm³. The machine includes a linear robot system and a 9-zone hot runner mold temperature control. Consider the opportunity to buy this DEMAG El Exis S250/630-2300 electrical injection moulding machine. Contact us for more information about this machine. • Clamping unit • Locking force: 2750 kN • Tie bar spacing (H x V): 630 x 630 mm • Platen dimensions: 950 x 950 mm • Mold installation height: min 330 mm / max 830 mm • Max daylight (open distance): 1505 mm • Opening stroke: 675 mm • Ejector: 200 mm stroke / 80 kN force • Mold weight capacity: 3300 kg total (1100 kg fixed / 2200 kg moving) • Injection unit (Type 840) • Screw diameter: 60 mm • Shot volume: 636 cm³ • Shot weight (PS): 579 g • Injection pressure: 1351 bar • Screw speed: 326 rpm • Plasticizing rate (PS): 74 g/s • Nozzle: radius 15 mm / bore 3 mm • Injection unit (Type 2300) • Screw diameter: 60 mm • Shot volume: 891 cm³ • Shot weight (PS): 810 g • Injection pressure: 2420 bar • Power and drive • System type: Hydraulic (pump motor) • Pump motor power: 37 kW • Installed heating power: 14.8 kW • Hybrid drive power consumption: • Total installed power: 124 kW • Electric screw drive: 47 kW • Electric clamp drive: 32 kW • Hydraulic pump: 22 kW • Options/controls • Core pulls: 2x (moving side) • Valve gate control: 1x hydraulic / 0x pneumatic Gjdeyftamopfx Abrjin • Mold temperature control: 9‑zone hot runner integrated • Interfaces: Printer, SPC process control • General specifications • Oil tank: 700 liters • Dry cycle: 2.00 s • Noise level: 74 dB(A) • Note from owner • Describes a hybrid high-speed machine with a larger injection unit (Type 2300 vs Type 840) than the referenced inventory machine above. Additional equipment • Linear robot W633-961 (axes: X=900 mm / Y=1600 mm / Z=2500 mm)

Condition: excellent (used), Year of construction: 2011, operating hours: 34,217 h, functionality: fully functional, clamping force: 2,000 kN, screw diameter: 50 mm, clearance between the columns: 570 mm, total length: 5,940 mm, total width: 2,000 mm, total height: 2,000 mm, overall weight: 8,300 kg, Injection Moulding Machines ARBURG Allrounder 570 H 2000-800 Stock No.: 503669 Manufacturer: ARBURG Model: Allrounder 570 H 2000-800 Control System: Selogica Year of Manufacture: 2011 Operating Hours: 34,217 h For sale is a used ARBURG Allrounder 570 H 2000-800, year 2011. This machine features a screw diameter of 50 mm and a clamping force of 2000 kN. Ideally suited for efficient and precise injection moulding applications in plastics processing. Gisdpoydkyzsfx Abrsn Contact us for further information and a customised offer! Technical Data – Clamping Unit Clamping force: 2000 kN Tie bar spacing (h x v): 570 x 570 mm Platen size (h x v): 795 x 795 mm Min. mould height: 250 mm Max. mould height: 550 mm Max. daylight: 1000 mm Opening stroke: 450 mm Ejector stroke: 200 mm Ejector force: 60 kN Movable platen centring diameter: 125 mm Fixed platen centring diameter: 125 mm Mould weight: 1300 kg Technical Data – Injection Unit Screw diameter: 50 mm Shot volume: 392 cm³ Injection pressure: 2000 bar Screw length: 20 l/d Screw stroke: 200 mm Screw speed: 60 rpm Screw torque: 1000 Nm Free-flow injection rate: 656 g/s PS Number of heating zones: 8 Nozzle stroke: 400 mm Dimensions & Weight Machine dimensions (LxWxH): 5.94m x 2m x 2.21m Total weight: 8300 kg Equipment HMI in German Levelling elements EUROMAP 67 handling interface EUROMAP 73 interface Mould heating 12x

Condition: ready for operation (used), Year of construction: 2004, operating hours: 96,194 h, clamping force: 2,000 kN, screw diameter: 40 mm, injection weight: 216 g, This Engel ES650H/200W-200HL-2F was manufactured in 2004. It features a clamping force of 2000 kN and platen dimensions of 920 x 760 mm. The machine includes a two-component system with screw diameters of 40 mm and 25 mm, and a robot system ERC 23/1-E for enhanced automation. Ideal for precision in hydraulic injection moulding. Contact us for more information about this machine. • Configuration: 2K (two-component injection molding machine) • Clamping unit: • Platen dimensions (H x V): 920 x 760 mm • Mold installation height (min): 500 mm • Opening stroke: 750 mm • Max. daylight (platen distance): 1150 mm • Max. mold weight: 3000 kg (1500 kg per side) • Ejector stroke: 150 mm • Ejector force: 80 kN • Core pulls: 3 (ejector side) • Centering ring diameter (ejector side): 200 mm • Injection unit 1 (Primary - 650H): • Screw diameter: 40 mm • Injection pressure: 1946 bar • Shot volume (swept): 251 ccm • Shot weight (PS): 216 g • Screw speed: 290 rpm • L/D ratio: 20 • Nozzle radius: 15 mm • Injection unit 2 (Secondary - 200W): • Screw diameter: 25 mm • Injection pressure: 2089 bar • Shot volume (swept): 69 ccm • Shot weight (PS): 60 g • Screw speed: 480 rpm • L/D ratio: 24 • Interfaces/Control: Printer interface; process control available Gedpfsyfrb Nex Abrjin Additional equipment • Robot system: ERC 23/1-E linear robot • X-axis stroke: 500 mm • Y-axis stroke: 1000 mm • Z-axis stroke: 1600 mm • Hot runner control: 16-zone

Condition: ready for operation (used), Year of construction: 2004, operating hours: 91,810 h, clamping force: 2,500 kN, screw diameter: 60 mm, injection weight: 579 g, This DEMAG ET250/630-840 Concept was manufactured in 2004. It features a clamping force of 2500 kN and a locking force of 2750 kN. The machine includes a Wittmann linear robot and supports a maximum mold weight of 3300 kg. It's equipped with a screw diameter of 60 mm and offers a shot volume of 636 ccm. Consider the opportunity to buy this DEMAG ET250/630-840 Concept hydraulic injection moulding machine. Contact us for more information about this machine. • Locking force: 2750 kN • Tie bar spacing (H x V): 630 x 630 mm • Platen dimensions (H x V): 950 x 950 mm • Mold height: 330–830 mm • Opening stroke: 675 mm • Max daylight (distance between platens): 1505 mm • Mold weight capacity: fixed side 1100 kg, moving side 2200 kg (total 3300 kg) • Ejector: • Stroke: 200 mm • Force: 80 kN • Centering ring diameter: 200 mm • Pneumatic ejector: yes • Core pulls: 2 on moving side (AS) • Injection unit: Gijdeyfq Alopfx Abrsn • Unit size: 840 • L/D: 20 • Shot volume: 636 cm³ • Injection pressure: 1351 bar • Plasticizing rate (PS): 74 g/s • Screw speed: 326 rpm • Nozzle radius: 15 mm; nozzle bore: 3 mm • Max dosing stroke: 225 mm • Note: Second injection unit listed with no data → single-component machine • Interfaces/controls: • Printer interface: yes • Process control/SPC: yes Additional equipment • Robot/handling: Wittmann W633-961 linear robot • Stroke: Y (vertical) 1600 mm, X 900 mm, Z 2500 mm • Hot runner control: 9 zones • Mold sensing: Kistler pressure (p=1) / temperature (t=0) system • Valve gate control: hydraulic (pneumatic not equipped)

Condition: good (used), Year of construction: 1994, Ref. no.: 17540 Hersteller: ARBURG Type: 270 C 500-100 RUNHOUR Only 100 Year of construction: 1994 Clamping unit Clamping force: 50 ton Opening stroke: 350 mm Distance between tie bars: 270 X 270 mm Mould height min.: 200 mm Platen size (h x v): 405 X405 mm Injection unit Screw diameter: 25 mm Injection volume: 67 cm³ Shot weight: 61 g Injection pressure: 2500 bar Gedpfsyiz U Tox Abrein Measurements and weight Dimensions: 3,3 X 1,5 X 2,0 m Machine weight: 2400 kg

Condition: good (used), Year of construction: 1989, Pressing area 2550 x 1350 mm Number of press cylinders #6 Total pressing force 140 t Opening width approx. 400 mm Operating voltage: 3 x 400 V + N, 50 Hz. Total connected load approx. 26 kW Space requirement (L x W x H) approx.: 3400 x 1600 x 2000 mm Weight: approx. 5500 kg Hydraulic hot plate press Down-piston design Electric hot platens Godpfx Abowd N Rmersin Pressing pressure continuously adjustable via pressure switch Hydraulic pump Central control panel with all operating and Digital temperature display for both hot platens Press cycle counter Safety ripcord Rack compensation Main switch Note for used machines: • Errors in technical specifications and subject to prior sale. • Subject to change without notice. • Prices quoted are for pickup from the location - free shipping! • The machines have been cleaned and functionally tested. • All machines are sold as seen, without any warranty. The buyer is free to inspect the machines on site. • Special agreements are only possible in writing. (We will only respond to inquiries if you provide your address and telephone number!)

Condition: ready for operation (used), Year of construction: 2012, operating hours: 73,437 h, clamping force: 1,600 kN, screw diameter: 45 mm, total height: 2,095 mm, overall weight: 8,700 kg, product length (max.): 5,155 mm, This Engel VICTORY 650/160 tech was manufactured in 2012. It features a tie-bar-less design, enhancing flexibility and accessibility for various mould sizes, with a clamping force of 1600 kN and a screw diameter of 45 mm. It's equipped with a robot, ensuring efficient automation. If you are looking to get high-quality injection moulding capabilities, consider the Engel VICTORY 650/160 tech machine we have for sale. Contact us for more information about this machine. • Operating hours: 73,437 h • Condition: Excellent • Status: In production • Maximum injection volume: 318 cm³ • Minimum mould height: 292 mm • Maximum mould height: 900 mm • Platen opening stroke: 609 mm • Platen dimensions: 750 × 750 mm • Tie-bar distance: Tie-bar-less design • Motor power: 22 kW • Heater power: 13.35 kW • Number of electrical connection pins: 16 • Injection nozzle radius (tip): R35 • Centering ring diameter: 125 mm • Number of cores: 0 • Number of heating zones: 0 Gisdpfx Asx Nr Huobrjn Additional equipment • Equipped with robot: Yes • Robot interface: Euromap 67

Year of construction: 2006, condition: ready for operation (used), An injection molding machine used in a cleanroom with a laminar flow module Max Patek and diverter is available. Clamping force: 500kN, screw diameter: 30mm, max. ejector stroke: 125mm, mold installation height: 200mm, tie bar spacing: 320mm, max. shot volume: 77g, platen spacing: 550mm, flow module air capacity: 450m³/h, operating hours: approx. 62000h. Without temperature control units and hopper dryer. The machine shows paint flaking, and the hydraulic hoses should be replaced. Documentation available. An on-site inspection is possible. Giodsykbgfspfx Abren

Condition: ready for operation (used), Design: vertical press with four columns. Gjdstty Nkjpfx Abrsin The vertical press platen is driven by an electric motor, the lower platen can be pulled out with the tool. -Dimensions: 2100x1600x3000mm -plate size: 950x1120mm -Electrical data: 380V; 43A; 22kW

Condition: excellent (used), Year of construction: 2022, operating hours: 2,100 h, 1x Arburg 320C 500-170 Golden Edition with Integral Picker Year of manufacture: 05/2022 Operating hours: 2,100 A total of 3 machines are available! 1x Year: 2020 2x Year: 2022 Equipment: - CG series - 320 C 500 - 170 - Complete 35 mm wear-resistant thermoplastic cylinder - Standard screw coupling, square coupling geometry - Selogica direct control system - Hydraulic system with 2 variable displacement pumps - Anniversary model GOLDEN EDITION - Thermoplastic processing Gisdpfxjyi Axms Abron - Open nozzle 35 mm - Nozzle tip radius 35 - Heating band for open nozzle - Central clamping platen set 320, Ø 125 mm - Pneumatic maintenance unit with 1 pressure regulator (1x1000 l/min) - Electric connection for blow-off device 1 on machine base - Blow-off device 2 with 3/2 valve on machine base - Selector unit, longitudinal mounting including connection - Mold clamping while safety guard is open - Programmable conveyor belt in the machine base, longitudinal - Preparation for INTEGRALPICKER V - Robot interface (according to EUROMAP 67), 50-pin - Socket combination 1CEE, 1 Schuko protected by 30mA residual-current circuit breaker type B - Basic Connectivity for additional "Connected Services" - Serial printer interface USB - CompactFlash interface for data record storage - Operator authorization with chip card according to EUROMAP 65 - Parallel connection for heating band nozzle tip or adapter - Freely configurable page for "start-up parameters" - Coloring device interface - Shut-off valve for cooling water inlet - Cooling water filter 100 µm supplied separately - 3 manually adjustable free cooling circuits - GOLDEN Automation Package with IP-V - Regulated machine cooling circuits - aXw Control Setup Bundle - aXw Control Start-Stop Bundle - ARBURG Remote Service (ARS) - Productivity package - Initial setup by ARBURG service - CD with operating instructions and spare parts list - Signage language German (DE) - Without granulate container 50 L - Without heating band for nozzle tip - Elastic machine mounting on vibration-damping mounts - Ejector plate connection safety - Quick-release coupling for ejector - Water-cooled control cabinet - Hydraulic ejector - Open-top safety device - Standard equipment packages - Machine equipped with INTEGRALPICKER - New ARBURG color scheme 5625-S356/XX-B-Z150 Centered in moving mold clamping plate 150 mm instead of 125 mm

Condition: excellent (used), Year of construction: 2007, Arburg 320C 500-100 (2007) Clamping force: 50 t Screw diameter: 25 mm Opening stroke 350 mm Mould height : 200 mm Distance between tie bars V: 320 mm Distance between tie bars H: 320 mm Mould clamping platens: 446x446 Injection pressure : 2240 Injection flow : 124 cm3 Ejector stroke : 125 mm Ejector force: 30 kN Net weight : 2080 kg Type: Horizontal Drive: Hydraulic Selogica CF card reader Gedpou Dmgqefx Abrsin machine tested English language

Condition: excellent (used), Year of construction: 2004, Clamping force: 25/35 tons Opening stroke: 200 mm Mould height: 150-300 mm Clamping platen daylight: 350-500 mm Tie bar daylight: 221 mm Mould clamping plattens (b x h) : 342 x 250 mm Ejector stroke: 60 mm Screw diameter: 25 mm Screw stroke: 100 mm Injection volume: 70 cm3 Shot weight: 59 g Injection pressure: 1040 bar Working hours: 34.748 Gedpfxeuykh Ds Abrjin

Condition: excellent (used), Year of construction: 2004, Arburg 520 TV 1300-350 (2004) Clamping Unit: 1. Clamping Force: 1,000 kN (100 tonnes) 2. Opening Force: 115 / 300 kN 3. Opening Stroke: 300 mm 4. Maximum Distance Between Platens: 600 mm 5. Minimum Mould Installation Height: 300 mm 6. Tie Bar Spacing: 1,300 mm 7. Maximum Weight of Movable Mould Half: 500 kg 8. Ejector Force: 45 / 175 kN 9. Ejector Stroke: 150 mm Injection Unit: Gjdpfxjwp E E Rj Abrein Screw Diameter: 40 mm Injection Volume: 230 cm³ Injection Pressure: 1,670 bar

Condition: ready for operation (used), Year of construction: 2016, operating hours: 37,049 h, clamping force: 4,000 kN, overall weight: 21,000 kg, This Arburg 820 S 4000 - 2100 was manufactured in 2016. It features a clamping force of 4000 kN, a screw diameter of 60-100 mm, and a shot weight up to 1860 g. The machine is equipped with a SEPRO SR AXESS 30 S3 robot and has a hydraulic pump drive power of 55 kW. Ideal for precision in plastic injection molding. Contact us for more information about this machine. Clamping unit • Locking force (max.): 150 kN • Opening force (max.): 100 kN / increased: 800 kN • Opening stroke (max.): 700 mm • Mold height (min.): 350 mm • Distance between platens (max.): 1050–1550 mm • Clear tie bar distance: 820 × 820 mm • Mold mounting platens (W × H): 1171 × 1171 mm • Mold half weight (max.): 4500 kg • Ejector force (max.): 100 kN • Ejector stroke (max.): 250 mmHydraulics / drive / miscellaneous • Hydraulic pump drive power: 55 kW • Installed total power: • 4000-2100: 88.9 kW • 4000-3200: 96.2 kW Giedpfoydpvbox Abren • Color: Plastic-coated structure (light gray / mint green / rapeseed yellow) • Control cabinets: Safety regulation DIN EN 60204 • Socket combination: 1 Schuko + 1 Cekon • Injection unit power supply: 1 × 16 AInjection unit • Effective screw length (L/D): 23/20/17.5 | 70/80/90 | 23/20/18 • Screw diameter (mm): 60/65/70 | 80/90/100 | 60/65/70 • Theoretical shot volume (max., cm³): 792/1078/1407 | 2513/3462/4240 | 1132/1608/2036 • Shot weight (max., g PS): 293/384/1826 | 1255/1469/1860 | 820/1167/1477 • Injection pressure (max., bar): 2500/2000/1530 | 2500/1500/1200 | 2500/2000/1530 • Injection flow rate (max., cm³/s): 294/362/400 | 812/1030/1250 | 312/396/440 • Injection flow rate with accumulator (max., cm³/s): 354/450/502 | 1188/1552/1964 | 375/475/528 • Back pressure positive/negative (max., bar): 350/50 | 350/50 | 350/50 • Screw circumferential speed (max., m/s): 0.38 | 0.28 | 0.28 • Screw torque (max., Nm): 2057/2247/2247 | 6757/80 | 2057/2247/2247 • Nozzle contact force (max.): 110 kN • Nozzle stroke (max.): 600 mm • Heating zones / heating capacity: 6 × 4500 + 3300 | 6 × 5500 + 4300 • Installed nozzle heating: 1000 W | 1250 WDimensions and weights (base machine) • Clearance length: 490 mm • Electrical connection (fuse protection) motor + heating: 250 A • Electrical connection (fuse protection) motor: 125 A • Electrical connection (fuse protection) heating: 50 / 63 A Additional equipment • SEPRO SR AXESS 30 S3 robot (2008)

Condition: excellent (used), Year of construction: 2015, Equipment: documentation/manual, Clamping force: 100 t Opening max: 500 mm Mould heigh: 250 mm Platen size: 590x600mm Distance between tie bars V: 420 mm Distance between tie bars H: 420 mm Giodpfeyg Eu Sox Abren Type: Horizontal Drive: Hydraulic Screw diameter: 30 mm Injection weight: 103 g Injection volume: 115 cm3 Injection pressure: 2755 extra equipment: 1. 2 hydraulic core pull circuits on moving platen (proportional valves) 2. Additional connections for 2 core pulls on fixed platen 3. Pneumatic core pull (2 circuits) on moving platen 4. 4-zone cooling water flow controller with temperature display 5. Compressed air blow valves on fixed and moving platens (programmable) 6. Integrated hot runner control, 8 zones 7. Interfaces for external nozzle heating bands 8. Interface for integrated temperature control units (up to 6 circuits) 9. Interface for mould temperature monitoring (2 circuits) 10. EUROMAP 67 for automation equipment

Condition: ready for operation (used), Year of construction: 2011, clamping force: 4,200 kN, screw diameter: 80 mm, injection weight: 1,464 g, total height: 2,500 mm, overall weight: 25,500 kg, controller manufacturer: KRAUSS MAFFEI, controller model: MC5, product length (max.): 7,300 mm, This Krauss Maffei 420-3000 CX was manufactured in 2011. A robust hydraulic injection molding machine from Germany, it features a clamping force of 4200 kN and a screw diameter of 80 mm. It supports a shot weight for PS of 1464 g and an injection rate of 478 cm³/s. Ideal for high-volume production with its 1200 cycles/h dry cycle rate. Contact us for more information about this machine. • Electrical data: • Power supply: 400 V / 3N~ / 50 Hz • Installed heating power: 36 kW • Rated pump motor power: 75 kW • Number of barrel heating zones: 7 • Performance and control: • Dry cycles (Euromap 6): 1,200 cycles/h • Control system/version: MC5 3.3 • Machine color: grey / white / blue • Clamping unit: • Mold opening force: 249.6 kN • Distance between tie bars: 800 × 800 mm Gedpfx Abeydnp Horjin • Moving platen force (open/close): 124.7 / 102.4 kN • Platen dimensions: 1270 × 1200 mm • Mold opening stroke: 1020 mm • Minimum mold height: 380 mm • Ejector stroke: 250 mm • Platen opening stroke: 1400 mm • Injection unit: • Nozzle tip radius: 15 mm • Nozzle orifice diameter: 6 mm • Injection pressure: 1856 bar • Injection volume: 1608 cm³ • Injection rate: 478 cm³/s

Condition: ready for operation (used), Year of construction: 2007, clamping force: 5,000 kN, overall weight: 26,400 kg, This 3-axis Arburg Allrounder 920S 5000-3200 hydraulic injection moulding machine was manufactured in 2007. It features a maximum clamping force of 5,000 kN, a screw diameter range of 70 to 90 mm, and a maximum shot weight up to 1,860 g. Consider the opportunity to buy this Arburg Allrounder 920S hydraulic injection moulding machine. Contact us for more information about this machine. • Maximum mold opening force: 150 kN • Enhanced opening force: 100 / 1,000 kN • Opening stroke: up to 900 mm • Mold height: min. 400 – max. 1,050 mm • Distance between platens: 1,300 – 1,950 mm • Tie-bar spacing (H × V): 920 × 920 mm • Platen size (W × H): 1,280 × 1,280 mm • Movable platen weight (half): max. 8,000 kg • Ejector force: max. 800 kN • Ejector stroke: max. 250 mm Hydraulics / Drive • Hydraulic pump motor power: 75 kW • Dry cycle time (opening stroke 5): 4.5–6.44 s • Installed total power: 96 kW • Color: Structural light gray / mint green / red-yellow • Control cabinet safety standard: DIN EN 60204 • Socket combination: 1 × Schuko, 1 × CEE Injection Unit • Screw diameters: 70 / 80 / 90 mm • Effective screw length (L/D): 23 / 20 / 18 • Maximum shot volume: 1,232 / 1,608 / 2,036 cm³ • Maximum shot weight (PS): 1,125 / 1,469 / 1,860 g • Plasticizing capacity (PS): 185 / 215 / 250 kg/h • Maximum injection pressure: 2,500 / 2,000 / 1,580 bar • Injection rate: Godpfeydnigsx Abrsin • Without accumulator: 290 / 380 / 482 cm³/s • With accumulator: 1,188 / 1,552 / 1,964 cm³/s • Holding pressure: max. 350 / 200 bar • Screw speed: 47 / 54 / 61 rpm • Screw torque: 3,500 Nm • Nozzle contact force: max. 110 kN • Nozzle stroke: max. 675 mm • Installed barrel heating power: 6 × 5,500 + 4,300 W • Installed nozzle heating power: 1,100 W • Oil fill volume: 590 liters • Motor + heating fuse rating: 200 A • Motor fuse: 125125 A • Heating fuse: 63 A

Condition: ready for operation (used), Year of construction: 2022, clamping force: 3,430 kN, screw diameter: 60 mm, total height: 2,397 mm, overall weight: 21,000 kg, product length (max.): 8,073 mm, This Toyo Si-350-6S JH750E-PACK was manufactured in 2022. It features a clamping force of 3430 kN, screw diameter of 60 mm, and an injection speed of 300 mm/s. With a total installed power of 85.6 kW and dimensions of 8073 × 1930 × 2397 mm, it represents a robust choice for precision molding. Contact us for more information about this machine. • Installed heating power: 27.5 kW • Total installed power: 85.6 kW • Control system: SYSTEM 800 • Interfaces: Euromap 67, Euromap 73Clamping unit: • Distance between tie bars: 810 × 810 mm • Platen dimensions: 1050 × 1050 mm • Opening stroke: 700 mm • Mold height (min / max): 300 / 770 mm • Ejector stroke: 150 mm • Ejector force: 60.0 kNInjection unit: • Injection speed: 300 mm/s • Injection pressure: 220 MPa • Holding pressure: 200 MPa • Theoretical injection volume: 763 cm³ • Injection rate: 848 cm³/s Gsdpfx Aboydnbporjin • PS injection capacity: 210 kg/h • Screw speed: 0–350 rpm • Injection stroke: 270 mm • Nozzle contact force: 39.0 kN

Condition: repair required (used), Year of construction: 1990, Technical details Clamping unit Clamping force: 850 kN Max. mould opening force: 37 kN Size of mould platens (W x H): 490 mm x 490 mm Distance between tie bars (W x H): 320 mm x 320 mm Mould opening stroke: 375 mm Minimum mould height: 250 mm Max daylight: 625 mm Gedpfx Asyhbvbsbrein Screw diameter: 45 mm Shot weight, PS: 214 g Injection rate: 180 ccm/s Injection stroke: 150 mm Screw speed: 52 m/sec Nominal capacity of pump motor: 15 kW Installed heating capacity: 5.5 kW Additional information The machine will not start due to a program error! Currently not operational!!

Condition: good (used), Year of construction: 2001, functionality: fully functional, Equipment: documentation/manual, • Clamping Force: 80 tons (800 kN) • Screw Diameter: 35 mm • Shot Weight (PS): 165 grams • Tie Bar Spacing (H × V): 420 mm × 420 mm • Opening Stroke (Max): 450 mm • Minimum Mould Height: 250 mm • Maximum Daylight (Platen Distance): 700 mm • Control System: Selogica • Power Consumption: 29.9 kW • Machine Dimensions (L × W × H): 5,200 mm × 1,600 mm × 2,200 mm • Machine Weight: 3,800 kg Gjdpfx Abewgamksroin Euromap

Condition: excellent (used), Year of construction: 2020, operating hours: 4,800 h, 1x Arburg 320C 500-170 Golden Edition with Integralpicker Year of manufacture: 11/2020 Operating hours: 4,800 A total of 3 machines available! 1x Year: 2020 2x Year: 2022 Equipment: CG series 320 C 500 - 170 Thermoplastic cylinder complete, 35 mm, wear-resistant Standard screw coupling, two-flat coupling geometry Selogica direct control system Hydraulic system with 2 variable displacement pumps Anniversary model GOLDEN EDITION Thermoplastic processing Open nozzle 35 mm Nozzle tip for open nozzle Heating band for open nozzle Clamping platen set 320 central Ø 125 mm Electrical connection for blow-off device 1 on machine frame Selector unit, longitudinal installation including connection Programmable conveyor belt in machine frame, longitudinal Preparation for INTEGRALPICKER V Robot system interface (according to EUROMAP 67), 50-pin Basic Connectivity for additional "Connected Services" Printer interface, serial USB CompactFlash interface for data storage Operation authorization with chip card according to EUROMAP 65 Parallel connection for heating band nozzle tip or adapter Freely configurable page for "start-up parameters" Color dosing unit interface Shut-off valve for cooling water inlet Cooling water filter 100 µm included 3 manual-adjustable free cooling circuits GOLDEN Automation Package with IP-V Regulated machine cooling circuits aXw Control Setup Bundle aXw Control Start-Stop Bundle ARBURG Remote Service (ARS) Productivity package Gisdpfx Aoyibayobrsn Initial commissioning by ARBURG service Instruction and training on the machine at customer's site CD operating manual and spare parts list Label language German (DE) Without granulate container 50 L Without heating band for nozzle tip Flexible machine mounting on anti-vibration elements Connection for ejector plate safety Quick-release coupling for ejector Water-cooled control cabinet Socket distributor: 1 CEE, 1 Schuko Hydraulic ejector Safety guard open at the top Standard equipment packages Machine equipped with INTEGRALPICKER New ARBURG color scheme