Used welding machinery for sale (30)

Year of construction: 2007, condition: used, dimensions 1.900 x 2.131 x 3.023 ,, weight of the machine ca. ca. 2.200 kg In our assessment, the heating element welding machine is in good used condition. Technical Specifications: Fodozbvnxspfx Aidjgd Compressed Air: - Max. operating pressure: 6 bar - Compressed air consumption: 0.2 Nm³/cycle at 5 bar Heating Mirror: - 2x12 WALTOW heating cartridges, Ø12.5 x 400 mm, 1000 Watts, 230 Volts - 2x PT100 thermocouples - Heat-up time to 350°C: approx. 50 min Vacuum Pump: - BECKER vacuum pump, Model VT 4.16, 550 Watts Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes and errors in technical data and specifications, as well as prior sale!

Condition: like new (used), Year of construction: 2021, operating hours: 300 h, 3x VE20 Microbond SCI 3x New The parts have been in operation for approximately 200-300 hours. Fgsdpfx Aisr Rdd Nodod The MICROBOND CSI system, consisting of a feed unit, control system, and high-performance generator, guarantees consistent welding quality. Robust yet highly precise mechanics enable constant gap control thanks to the patented MicrogapControl gap control system. The MICROBOND control system controls and visualizes this continuous joining process. Constant amplitude output and high continuous sound power enable process speeds of up to 800 m/min.

Year of construction: 2020, condition: ready for operation (used), A Schirmacher high-frequency sliding-table welding machine is available. Table dimensions X/Y: 750mm/550mm, max. pressing force: 20kN, generator output: 10kW, operating frequency: 27.12MHz, control system: Siemens. Documentation available. An on-site inspection is possible. Fgjdozh Niujpfx Aidjd

Condition: as good as new (ex-display), PFAFF 8320 - 111/101 long-arm version with table Fgodpexa D Hrsfx Aidsd

Year of construction: 1999, condition: excellent (used), working width: 620 mm, machine/vehicle number: SE 01510 A10, Heating Element Welding Machine HP60/40 by BRANSON The drive is hydraulic, supported by positioning and control systems. The machine is equipped with its own vacuum pump. Only a few operating hours (approx. 6,800 hours). Usable heating element area: width 600 mm x depth 400 mm Max. workpiece dimensions: - Max. width: 620 mm - Max. depth: 420 mm - Max. upper height: 350 mm - Max. lower height: 350 mm (Combinations of part heights possible, depending on contour) - Max. processing temperature for contact method: 400°C The modular frame design allows for easy conversion and retrofitting. The side doors and the front door in the welding area can be easily opened (for rapid retooling). The automatic safety lift door ensures a high level of operator safety. The temperature control units on the operator panel have actual/target displays. The control device is a Siemens PLC HMI. The machine is controlled by a Siemens PLC (S7-300 controller). Heating elements are equipped with temperature sensors for temperature regulation and serve as safety cut-offs in case of overheating. The pin systems in the tool mounting surfaces ensure reproducible positioning. Advantages of heating element welding technology: - Reliable welding of workpieces with low or varying wall thicknesses. - Low scrap rate due to dimensionally accurate and repeatable welds. - Precise time, temperature, and force control enable welding of sensitive parts. Fedpfx Aijykvdlsdegd - Virtually all thermoplastics can be welded with this process. - Different thermoplastic types can be joined (compatibility needs to be verified). Technical data of the machine: - Power supply: 3 x 400 V AC + N + PE - Power: 25 kVA - Rated current: 20 A - Required cable cross-section: 5 cables, each 6 mm² - Required pneumatic connection: 6 bar Machine dimensions: - Machine width: approx. 1.22 m - Machine width with operator panel: approx. 1.8 m - Machine depth: approx. 2.1 m - Machine depth with operator panel: approx. 2.6 m - Machine height: approx. 2.4 m - Machine height with raised safety door: approx. 2.85 m (open door) Machine weight: approx. 2.2 t

Condition: refurbished (used), Year of construction: 2009, operating hours: 200 h, functionality: fully functional, machine/vehicle number: P.TE 1-350, total width: 700 mm, total length: 900 mm, total height: 600 mm, warranty duration: 12 months, length of welding knife: 500 mm, width of welding knife: 10 mm, High frequency welding machine THF producer, reviewed by Cebb HF Technology in 2026 35cm of arm 1,5KW of power Welding electrode 500x10mm or 250x20mm Possibility of welding with small additional shaped electrodes Fgjdpfx Aoy Nkiboidjd Dimensions 700x900xH600 to be placed on top of a table original plexiglass shielding 12 months warranty

Year of construction: 2009, condition: excellent (used), functionality: fully functional, machine/vehicle number: 579-130-09, Printed with 1S1C by Meca Tecno srl, Italy. The machine can be tested. In very good condition. Fjdpszfgigofx Aidogd Regularly maintained. Please contact us for more information.

Condition: excellent (used), For sale: Professional KLN Ultraschall / MECASONIC OMEGA 3 MCA ultrasonic welding machine – an industrial system for precision joining of plastics. The device is designed for use in: - Serial production - Automotive industry - Electronics and medical sectors - Welding plastic components (e.g. housings, blisters) ⚙️ Specification: Manufacturer: KLN Ultraschall (Crest Group) / MECASONIC Model: OMEGA 3 MCA Type: Ultrasonic welding system Year of tooling production: 2011 Control: MCA digital control panel Cycle counter: approx. 23,000 Two-hand safety start system (operator safety) Fgedpfxsyzui Ao Aidsd Industrial power supply 📦 Included in the set: - Complete welding unit - MECASONIC MCA controller - Work table with tooling (mould / fixture – "Blister") - Pneumatic installation (visible in the photos) - Cabling 📊 Condition: - Used device - Visually in very good condition - Normal signs of use (as seen in the photos) - Machine powers up – control panel operates - No complete production testing performed 📄 Additional information: - Cycle counter visible on display - Safety instructions (DE) on the housing - Robust industrial construction ✅ Advantages: - High welding precision - Fast process (ultrasonic) - Reliable industrial technology - Ready for integration or standalone operation - Reputable manufacturers (KLN / MECASONIC) 🚚 Shipping: - Pallet shipping - Personal collection possible - International shipping available

Year of construction: 2021, operating hours: 227 h, condition: excellent (used), functionality: fully functional, The HF machine was used for welding PVC tarpaulins. Maximum welding area: 4 cm x 100 cm. Fedpszbb Tmofx Aidogd Current welding stamp sizes: 2 cm x 100 cm and 2 cm x 50 cm, in use since 02/2022.

Year of construction: 2015, condition: excellent (used), Mecasonic MCS2 CAB ultrasonic welding system Fgsdevvw Ekepfx Aidsd - Very good condition - Year of manufacture: 2015 - 3 units available - CE declaration of conformity given - Condition: Incoterms EXW CH-4528 Zuchwil - Loading options available

Year of construction: 2023, condition: used, We offer this used Weber Ultrasonics Saphir Digital Manual Station ultrasonic welding machine, year of manufacture 2023. Approximately 92,500 units have been produced with this machine. Sonotrode TR35Ti Frequency: 35 kHz Fodpfxjyimqwj Aidjgd Power: 1000 W 230V AC Stroke measurement system: 26.88 mm Minimum force: 34 N Maximum force: 500 N Low Level: 0 N Low Offset: 0 N If you have any questions or require further information, please feel free to send us a message or call us.

Year of construction: 2015, condition: used, functionality: fully functional, The pneumatic butt welding device, type Sv‑63P, is equipped with a robust vertical frame that includes vertical clamping jaws and a sliding movable plate. Clamping is achieved via tandem cylinders, while the support plate on the static side is isolated from the base frame, which also carries the movable carriages. These carriages are connected to a horizontal cylinder for compressing the workpiece. The carriage movement is limited in both directions—both for compressing and opening—while the distance between the clamping jaws can be adjusted according to the cross-section or diameter of the workpiece. Clamping with the set jaw distance is controlled using foot switches. An additional control cabinet with switches and push-buttons allows for single or simultaneous clamping and supports both manual and automatic welding operations. After welding, the clamping jaws lift, and the carriages return to their initial positions. The welding parameters are set using a controller mounted on the side of the device. The welding voltage is regulated by thyristors, and the power transformer is fully encapsulated and water-cooled, connected to the contact jaws via laminated conductors. Inside the device, a power board with a thyristor and a main control board ensure smooth operation. On the device cover, a compressed air maintenance unit with a pressure regulator is installed to adjust the clamping force. The main switch to activate the unit is located on the controller for setting the welding parameters. Fjdpeyqr Sxsfx Aidegd

Year of construction: 2013, condition: excellent (used), Ultrasonic welding system Manufacturer: KLN Stock number: Year of manufacture: 2013 or 2009 Type: PXO number P600031440 MXO number M60413293 Equipment: the system consists of two stations, Individual sale possible Price: EUR 5,000 per station Fjdpfx Aisvxppaodsgd Price including 19% VAT: EUR 5,950 per station

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: DC, input voltage: 400 V, total height: 2,890 mm, total width: 2,440 mm, total length: 2,890 mm, Mobile Welding Station 10ft for PE/PP Pipes incl. HÜRNER CNC 500 (SST Series) Weather-Independent Butt Fusion Welding at Industrial Standards Fgodeyzn Ifepfx Aided Stop building makeshift welding tents on site. This compact 10-foot welding station (SST 10 / 500) is a self-contained, ready-to-use production cell for demanding PE/PP pipeline construction. Plastic weld seams do not tolerate drafts or moisture—this container guarantees consistent, standard-compliant environmental conditions and complete documentation. Your advantages in pipe handling: The bottleneck on site is the handling. This station is uncompromisingly designed for ergonomic efficiency. Pipe sections are passed directly through the container using the 800x800 mm end-side pipe doors (with integrated brush seals). The built-in 1,000 kg lifting table, mobile pipe lifters, and an electric chain hoist make handling pipes up to OD 450 mm an efficient one-person job. Plug & Play: Connect power and start welding. Technical Data (SST 10 / 500): Container: 10" High Cube, Double Door, One Way (incl. chequer plate steel floor) Welding machine: HÜRNER CNC 500 ECO 2.0 USB & Bluetooth data management Working range: OD 200 to OD 450 mm (including reduction inserts) Lifting technology: Electric lifting table (1,000 kg), electric chain hoist with trolley/manual trolley (3m lift) Pipe handling: 2x universal mobile lifters (up to DN500), 2x pipe doors (800x800 mm) Power supply: 32A & 16A CEE (400V), 3x 16A Schuko (250V IP54), RCD 63A Lighting: 2x LED floodlights (24,000 lm, 5000 K), 2x LED moisture-proof fittings Condition: Fully prepared for welding (CE), incl. DGUV inspection & 2x thick coat paint (color of your choice) (Note: Supplied without power generator) Available configurations in this series: This listing refers to version SST 10 / 500. We manufacture these stations in four standardized performance classes to suit your project: SST 10 / 355: 10-foot container, suitable up to OD 355 mm SST 10 / 500: 10-foot container, suitable up to OD 450 mm (offered model) SST 20 / 355: 20-foot container (extended work area), suitable up to OD 355 mm SST 20 / 500: 20-foot container (extended work area), suitable up to OD 450 mm Custom modifications are available on request. Contact us for a detailed quotation.

Condition: good (used), functionality: fully functional, Ultrasonic welding unit BRANSON, model 8.200 Fsdoylpqbjpfx Aidjgd

Year of construction: 2014, condition: ready for operation (used), An ultrasonic welding system with nine Telsonic Ultrasonic, cabin, nine generators and documentation is available. Control system: Siemens SIMATIC PANEL. On-site inspection is possible. Fodpjuy T Nqofx Aidsgd

Year of construction: 2018, condition: ready for operation (used), Number of heating cartridges: 24, heating cartridge average and length: 12.5mm/200mm, power: 630W, 230V, including resistance thermometer type PT100, heating time to 350°: 40min. Dimensions X/Y/Z: 1900mm/2100mm/3040mm, weight: approx. 2200kg. Documentation available. Fgedpfx Aietp Nacjdsd

Year of construction: 2009, condition: ready for operation (used), Welding force: 2500N, table dimensions: 420x415mm, height adjustment: 250mm, stroke: 100mm, control: Telsonic MPS-4, connected load: 4000W, length: 459mm, width: 854mm, height: 1315mm, weight: 130kg. With SICK C4000 safety light curtains, cabin and documentation. On-site inspection is possible. Fjdpfx Aeuy T I Hjidjgd

Year of construction: 2010, condition: ready for operation (used), An ultrasonic welding system with two Telsonic TSP-3000-1P, cabin, generators and documentation is available. Welding force: 2500N, table dimensions: 420x415mm, height adjustment: 250mm, stroke: 100mm, control: Siemens SIMATIC PANEL, length: 762mm, width: 854mm, height: 1316mm, weight: 130kg. On-site inspection is possible. Fgjdsuy T Ndspfx Aided

Year of construction: 2018, condition: ready for operation (used), Three almost identical CNC plastic pipe butt welding machines (mirror welding machines) Hürner are available. Years of construction: 2x 2016 and 1x 2018, working range OD: 40mm-160mm, power: 2.85kW, reduction inserts: 40/50/63/75/90/110/125/140, weight: approx. 80kg. Documentation available. On-site inspection is possible. Fgedpoviv Azefx Aided

Year of construction: 2025, condition: new, functionality: fully functional, High frequency generator Schirmacher HS25000 The HF generator is used to generate a high-frequency electromagnetic field, which in a connected HF production device can be used to - Heat and weld thermoplastic plastics, - Dry paper products, textiles, wood and similar materials, - Heat plastic granulates, rubber and other materials. Technical data Operating frequency: 27,12 MHz Output power: 25 kW Power supply: 3 x 400V, 50Hz, Rated power 46 kVA Control: Generator: SPS Siemens S7 / Control electronics: SE68 Triode: RS3026 CL, alternatively ITL 12-1 Anode voltage: Full load 9,1kV, no load 10,4 kV Anode current: Full load 3.800 mA, no load 800 mA dimensions (WxDxH): 1.200 x 1.200 x 2.000mm Commerical infromation Condition: new machine, from delivery stock – zero operating hours Manufacturer: Heinz Schirmacher GmbH, Trittau Fgodpfx Aiex U Trpedsd Availability: Available from stock, more than one unit in inventory Warranty: Available upon request Machine highlights Fast commissioning through modular design – flexible integration into various production processes and adaptation to different tools. Highly precise control – exact power delivery and consistently high welding quality. Highly dynamic HF regulation prevents extremely rapid flashovers in the welding process. Electrode protection – integrated into the generator to safeguard both machine and tool. Automation-ready – suitable for use in automated manufacturing processes with the capability to integrate into existing systems. Visits possible by arrangement.

Year of construction: 1995, condition: good (used), welding machine Branson HP 25/15-1, year: 1995 , price: 4.900 €, contact: Mr. Rainer Eckerle Fgsdpodzngfsfx Aided

Condition: ready for operation (used), There are two identical machines available, including documentation. Fodpfx Asm Rg R Aoidjgd

Year of construction: 2008, condition: ready for operation (used), Stroke: 100mm, max. electrode distance: 230mm, electrode distance: 20kN, controls: Siemens S7-1500, with documentation, was hardly used. Fsdpfx Aiolp N Eyodogd

Year of construction: 2007, condition: used, welding machine KVT MT 01-HAT SO, with Rotary table, year: 2007 - 0 working hours, price: 8.800 €, contact: Mr. Rainer Eckerle Fsdpfx Aocquugeidjgd