Used Thermoform for sale (174)

Condition: excellent (used), Year of construction: 1992, operating hours: 41,685 h, Technical specifications: Rated power, kW: 11,3 Mold area, mm: 475 x 250 Max. film width, mm: 495 Min. film width, mm: 150 Max. feed length, mm: 280 Min. feed length, mm: 50 Max. drawing depth/negative, mm: 100 Number of cycles/min.-max.: 48 Consumption of air/cycle at 6 bar: 100 Nl (net-pressurized air) Heat energy to be dissipated: Nwodpfx Agoq A Um Rozsr with top heating ca. 10 260 KJ/h with top and bottom heating ca.: 17 715 KJ/h Special equipment: Hollow floor facility available Control cabinet: included

Year of construction: 2001, condition: ready for operation (used), HEK GmbH VGO 200 S Heating cabinet Dimensions (approx.): Nwodpog Hzqbofx Agzjr Width: 1035 mm Depth: 800 mm + 210 mm tube Height: 820

Condition: as good as new (ex-display), machine/vehicle number: 1966190, Heating table HT3110 Nodpfxe T Sv Sj Agzswr For tempering thermoplastic materials such as mineral plastics, acrylics, etc. to the required processing temperatures. Torsion-resistant base frame consisting of welded steel profiles. Movable on four rollers. Upper folding frame at the rear side rotatably mounted in a solid spherical bearing. Two aluminium heating plates black anodized maximum operating temperature 180 C. Temperature control by means of electronic controller in separate switch cabinet in the base of the table. The swivel movement is actuated by pneumatic cylinders located on the side. Four adjusting screws on the side for setting the material thickness.

Condition: good (used), 8 head sauce depositing system to sit over Multivac thermoformer. Has been dosing sauces and gravies into pouches on Multivac machine. Bought new in 2019 and the factory closed shortly afterwards due to COVID Nwedpfoq Dagmsx Agzsr

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm vice 285 mm turning speed range: 36/72 m/min dimensions of saw-band 2950x27x0,9 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 485 kg dimensions of the machine ca. 1700 x 1000 x 1800 mm Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Semi-automatic function: At the start of the cycle: - Vice closes and motor starts – Saw head lowers for the cut – Motor switches off – Saw head rises – Vise opens. Semi-automatic dynamic system (manual lowering of the saw band bow up to to the desired position and cycle start via the manual button.) Some features: New centralized control console on an articulated arm to allow the operator can be easily switched from any working position. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed Nwedpefg E H Sofx Agzor * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Large work surface with turntable on roller bearings, measuring 265 mm preloaded thrust bearing, mounted. Double belt speed (36/72 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base frame with pull-out coolant tray. Electric coolant pump for cooling and lubricating the saw band. Preparation for installing the minimum blade lubrication kit (Optional), in addition to the conventional standard lubrication Emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: new, The Zerma ZCS Shredder integrates leading shredder and granulator technology into a single compact unit. With the development of the shredder and granulator combination, ZERMA has successfully continued the expansion of its product portfolio. By combining the proven design and high torque of the single shaft shredder with an extremely effective granulator, ZERMA can deliver a reliable and compact pre-shredding system. The shredder and the granulator are driven individually, which contributes to better control of the whole process. To increase the efficiency, ZERMA Smart Drive System is used to constantly control the load and adjust the amperage accordingly, resulting in reduced power consumption. The ZERMA ZCS can be used in any application where predictable quality in size reduction and granulation is required. Typical applications include, but are not limited to, the following: Injection Molding Thermoforming Blow molding Recycling Njdpfoghgd Ssx Agzowr Extrusion Waste

Year of construction: 1988, condition: excellent (used), machine/vehicle number: 3284, (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Nwsdpfxjhbu E Hj Agzjr Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe reliable guarantee for precision. OPTIMUM PUNCHING ACCURACY EVEN DURING MAXIMUM OUTPUT Cam controlled function sequence guarantees absolute precision with every cycle.

Condition: ready for operation (used), Technical characteristics membrane press type VPI3713 3740 x 1290 mm press area vacuum pump 140 m3 / h max pressure 9t / m² 1.25 kW thermoforming furnace type GETP 3714 heating zone 3700 x 1380 mm temperature 180 ° electric hotplate Nodst N Auyspfx Agzewr working height 1000 mm Power and Motors Overall dimensions

Year of construction: 1990, condition: refurbished (used), functionality: fully functional, machine/vehicle number: 647-230, Lid Punching machine without tools Type Hamba 647-230 foil width - 230 mm very good condition - with used embossing calender for worm structure - Power connection: 220/380V - three phases - Additional punching tools available - e.g. 1x 2-fold tool - diameter 80.50mm Nwodpfonr Ex Tsx Agzer 2x 2-fold tool - diameter 75.50mm 1x 2-fold tool - diameter 59.54mm 1x 2-fold tool - diameter 93.80x120.90mm

Condition: reconditioned (used), > Completely overhauled and newly painted. Nwjdpfjfua H Asx Agzor

Condition: new, cutting diameter 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: round 260 mm Nwjdofg E H Ujpfx Agzer capacity 45 degrees: square 250 x 250 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 170 x 170 mm capacity 60 degrees: round 180 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3320 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Some features: New centralized switch console on an articulated arm. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Turntable (on roller bearings of 420 mm with preloaded thrust bearings assembled). Double belt speed (40/80 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base designed to completely contain the coolant, even with maximum angle cuts. The coolant pan (provided with an electric pump for lubrication and Cooling of the saw band) and the chip drawer (can be replaced by a Chip conveyor to be replaced - see special accessories) are in the base frame built-in. Preparation for installing the minimum blade lubrication kit (Optional, in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Adjustable length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: new, MEP SHARK 282 SXI evo [Semi-automatic] All MEP models on request ! Motor power 1,5/1,8 kW Bank opening 285 mm belt dimensions 2950x27x0,9 mm Weight 485 Kg Speed 36/72 m/min. cutting surface 0° 250 / 220x220 / 280x220 cutting surface 45° right 230 / 200x200 / 220x200 Cutting area 45° left 200 / 170x170 / 200x140 Cutting area 60° right 120 / 80x80 / 140x80 Cutting area 60° left Description Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO with semi-automatic-dynamic manual function, has MEP-28 control for miter cuts from 45° right to 60° left. Semi-automatic function: At cycle start occurs: - Vise closes and motor starts - Saw head lowers for cut - Motor shuts off - Saw head raises - Vise opens. Semi-automatic dynamic system (manual lowering of the saw band to the desired position and cycle start via the manual button). Some features: New centralized control panel on articulated arm to allow the operator to easily switch from any working position. Control panel with low voltage: Membrane keypad in polyester with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in user language). * Alarms (description of alarm causes) * Status of inputs and outputs * Counting of the cuts * Time used for the performed cut Nwedpfx Agjcgbq Iozer * Current consumption of the saw band motor * Saw band tension * Saw band speed * Numerical display of the head position. Switch handle IP55 of the manual 24 V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for particular applications. New hydraulic control unit of the latest generation, highly efficient and with low energy consumption. Large work surface with turntable mounted on roller bearings, of 265 mm with preloaded thrust bearing. Double speed of the belt (36/72 m/min.) with control. Provided for the inclusion of an electronic inverter for the continuous regulation of the band speed from 20 to 90 m/min. Stroke of the saw bow programmable directly from the control panel, for adaptation to the material to be cut. Clamping device laterally movable to the left and right, with quick-action vice. Manually operated band tension control with display on the screen by means of electronic converter. Base frame with extendable coolant tray. Electric coolant pump for cooling and lubrication of the saw band. Preparation for the installation of the minimum lubrication kit of the saw band (optional), in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is designed for lift truck transport. Length stop for cuts of the same length material support arm with roller, for fixing the loading platform Bimetal saw band for solid and profiled material. Tools and instructions for use in the user's language. For further technical data, please refer to the attached PDF document.

Condition: excellent (used), Year of construction: 2000, machine/vehicle number: 403, THERMO FORMING MACHINE TFT IMC 5030 (WITH TOOLS) Equipment / Additional information: unwinding: Roll recording: easy Max roll diameter: mm 1000 Settlement: automatically Thermoforming machine: Maximum tool dimensions: mm 520x330 Pos. Molding height max .: 15 mm Neg. Molding height max .: 120 mm Sheet width: mm 150/760 Movement Step: mm 50/330 Max HIPS film thickness: 1.8 mm Hub of the sub-table: 150 mm Clamping force: 7500 Kg Inst power top heater: 18.8 Kw Inst power under heater: 14.1 Kw Idle clock speed: per minute 40th power main drive motor: 2.2 Kw Engine power. Film feed: 0.75 Kw Air operating pressure: Kg / cm2 7 Water consumption at 12 °: 1t / 1` approx.30 Air consump. at 7 kg / cm2: 1t / cycle 125 Installed power: Kw 50 9xTool: Article no. // Tool no. // Cavities // Description / Product: 3599 // 457 // 10 // Vending machine cup capacity/capacity/contenance=223ml 593 // 460 // 8 // Coffee-to-go / thermo mug / thermo cup Filling capacity / Capacity / Contenance=300ml / 12 oz 509 // 452 // 6 // Ice cream cup: filled to the brim=140ml / Filling capacity with headspace 6mm: 120 ml 591 // 459 // 10 // Thermo mug ⌀ 81/180ml 740 // - // - // Standard cup with sealing edge ⌀ 75-120ml 3589 // 458 // 12 // Coffee-to-go / thermo mug / thermo cup: Filling capacity / Capacity / Contenance=80ml Njdpjn D Ew Iefx Agzjwr 595 // 456 // 10 // Vending cup / Gobelet pour automate: Filling capacity / Capacity / Contenance=150ml 210 // - // - // Baking case / technical part / plate or tray 8000 // 455 // - // Granule cup 180 ml / technical part with flat sealing edge

Year of construction: 2013, operating hours: 1,234 h, condition: refurbished (used), functionality: fully functional, machine/vehicle number: o, TECHNICAL DATA – MAGIC SKIN 5035 Power supply: 240 V – 1 Ph Required power: 3.5 kW Overall machine dimensions (L x W x H): 1860 x 1000 x 1350 mm Working table height: 1020 mm Weight: 150 kg Njdpfx Ajxcv U Hsgzewr Maximum carton size: 495 x 345 mm Maximum product height: 100 mm Air consumption: – Performance: two cycles / min Notes: Technical modifications reserved. Performance depends on operator and type of packaging.

Year of construction: 2021, condition: ready for operation (used), A semi-automatic vacuum skin packaging machine (tray sealer) Sealed Air for Darfresh skin packaging is available. Packaging capacity: 15/min, cycle performance: 1.5 cycles/min, film width: 562mm, max. product dimensions X/Y/Z: 670mm/470mm/50mm, tray length range: 135mm-700mm, tray width range: 120mm-520mm, tray height range: 5mm-50mm. Machine dimensions X/Y/Z: approx. 1050mm/1650mm/1250mm, weight: approx. 500kg. Documentation available. An on-site inspection is possible. Nwodpfx Aoxaphbogzor

Condition: reconditioned (used), > Small moulding machine with the format 350x250x90. > For skinning and blistering of small batches. Nwjdpfx Aofugz Ujgzor > As a sample machine for every company. > Optionally also with upper punch. > Further details on request. > Completely overhauled and newly painted

Condition: good (used), Year of construction: 2013, Cabinplant MHW 40-24 Multihead Weigher and Cabinplant Depositor/Distributor Machine functions: - Product is fed to infeed system, consisting of an elevator; - The elevator is controlled by the infeed sensor of the multihead weigher; - The multihead weighing machine discharges weighed out portions to Distributor / Depositor; - Distributor / Depositor distributes portions, orientates the product and dumps finished portions into a thermoforming machine or traysealer; This line consist of the following equipment:  - SS Stair; - Infeed conveyor belt; - SS Platform; - Cabinplant MHW 40-24 Multihead Weigher; - Cabinplant Depositor / Distributor; Njdpewyu Trjfx Agzswr Cabinplant MHW 40-24 Multihead Weigher Manufacturer: Cabinplant Model: MHW 40-24 Year: 2013 Capacity: 150-500 gram Weighings/min.: Up to 120 Pan Size: 4 liter Number of pans: 24 Machine Dimensions LxWxH: 2.200x2.125x2.500 mm Machine Weight: 1.100 kg. Multihead Weigher is fully checked and serviced by Cabinplant Cabinplant Depositor / Distributor Manufacturer: Cabinplant Model: Sausage Depositor Year: 2014 Capacity: 150-500 gram Weighings/min.: Up to 120 Filling Capacity: 2x5 movable pitch

Condition: new, MEP COBRA 352 SX evo [Semi-automatic] Article number CB352SX motor power 1,5/2,2 kW belt opening 180 mm belt dimensions 350x32x3,4 Weight 285 Kg Speed 1700/3400 1/min. Cutting surface 0° 120 / 105 / 180x70 Cutting surface 45° right 120 / 100 / 135x60 Cutting surface 45° left Cutting surface 60° right Cutting surface 60° left Description Semi-automatic circular saw for sawing of solid and hollow aluminum materials and light alloys with electro-welded carbide tooth wheel. Basic equipment: -Machine for miter cuts from 45° right to 45° left. -Alignment along the vertical gives the possibility of sawing operations with head inclined between 0° and 45° left. -* MEP represents the latest generation of controls designed for semi-automatic machines with single axis microprocessors. -CHARACTERISTICS: At the start of the cycle: - Vise closes and motor starts - Saw head lowers for cut - Motor stops - Saw head raises - Vise opens. -New - Display with 16 characters x 2 lines for displaying the following technical parameters: + number of executed cuts + cutting time + ammeter + display of over 100 diagnostic messages and warnings. -New - Display and entry of the alarm and error messages with the possibility of displaying the incidents that have occurred. Electrical equipment: -New - Low voltage control panel: membrane polyester keypad with thermoformed and highlighted push buttons and actuation control signal. -Saw blade stroke programmable directly from the control panel, to adapt to the cutting material. Njdpschkv Isfx Agzewr -Ball bearing mounted rotary table to ensure easy and accurate rotation. -Clamping system consisting of two face vices that can be freely arranged along the longitudinal axis of the parts. -Adjustable mechanical stops for quick positioning of the head in the angular positions at 0° and 45° right and left. -Swarf extractor with preparation for OPTIONAL extraction system. -Automatic saw blade lubrication system, operating only at the start of the cut. -Machine is supplied without saw blade. -Preparation for the installation of the minimal lubrication kit of the saw blade (OPTIONAL), besides the conventional standard lubrication with emulsion oil. -Tool and instruction manual with spare parts list. For further technical data, please refer to the attached PDF document. Catalog 2nd page !

Condition: excellent (used), Year of construction: 1999, operating hours: 80,188 h, machine/vehicle number: 322, Max. film width 700-800 mm Equipment / Additional information: -GREINER STACKING / Transfer device R3 (Ref. No.: 95002.24) // M. No.: 00020 // Age: 1998 Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp Nwjdeq Nn Hcspfx Agzer The following tools were used on the machine: 8-way WZ-Ø95 and 15-way WZ-Ø73 and 15-way WZ-Ø86 Packaging was produced especially for the dairy industry. The cycles are 18-25 strokes - depending on the cup weight.

Condition: reconditioned (used), > Cut-off saw TS 100 c, with conveyor belt, suction belt, extraction, adjustable treadmill and saw blade. > 4 hold-down devices, new wheels and new bearings. > Machine completely overhauled and new painted. > Passage width of 600mm > Further details on request. Nodefua Dropfx Agzowr

Condition: excellent (used), Year of construction: 1998, machine/vehicle number: 00020, Type: Transfer device R3 Equipment / Additional information: Air pressure: min 6 bar The maximum size of the stacking basket is 530x300mm. Nsdpsupi Aqsfx Agzewr

Condition: reconditioned (used), > completely overhauled and newly painted > Passage width 900mm Njdpfx Agsfuaztozjwr > roller table

Condition: reconditioned (used), > Top heating with pilot radiator control > Single radiators of the top heating > 2 cooling fans D05 > Automatic preblow and demoulding > Documentation and plans in German > Max. forming area 1210 x 500 > Longitudinal and cross cutter with 6 quick-change squeezing knives > Euro hole punching device (can be retrofitted at extra charge) Nsdefua Huopfx Agzewr > completely overhauled

Condition: reconditioned (used), > Skin machine and blister machine with longitudinal and cross cutter, Euro perforation. > Completely overhauled and newly painted SB 74c-10 with steel strip punch and residual material take-up. New conveyor belt. > Size 770 x 505mm. > On request also as c-9 or with upper punch. Nodsfua S Sopfx Agzswr

Condition: reconditioned (used), > completely overhauled and newly painted > Passage width 600mm > roller table Nedpfxjfua Axs Agzowr