Used blow molding machines for sale (29)

Condition: used, Uniloy UR110 16 Head Reciprocating Screw Blow Moulding Machines (2x 2012) With Ancillary Equipment Each with: Uniloy Milacron RTM 4 trimmer (2012) Uniloy Milacron leakage control 5x Moretto hopper loaders Crodpfx Ahexn N Abe Uei 2x Moretto FC400PB filter units Shared between Uniloy blow moulders 3x Beccaria TV 2500 granule mixer dryer, 2,500L capacity Maguire WSB-940T gravimetric blender Moretto TLC 05S3 manifold Moretto VTS1120W60 side channel suction unit Tria BM90-42 granulator with acoustic enclosure (2014) Demag pillar jib crane

Condition: excellent (used), Year of construction: 2013, operating hours: 200 h, functionality: fully functional, screw diameter: 65 mm, overall weight: 9,000 kg, clamping force: 785 kN, total width: 1,800 mm, total length: 4,500 mm, total height: 3,000 mm, power: 0.045 kW (0.06 HP), We offer for sale a slightly used injection blow moulding machine in excellent condition. It is connected and fully operational for demonstration purposes. We can also offer several ready-made molds for canisters and lamp shades. The machine is designed for use with PMMA, PC, PP, and PE resins. Crsdpfxothk Rzo Ah Uei

Condition: used, Year of construction: 1995, SIDEL SBO10- blowing machine SBO10 is intended to manufacture PET bottles. Its production rate can be up to 10.000 bottles per hourdepending on the capacity. As first step, the operator puts the preform bin, via trans pallet or forklift, in the hoisting and tipping unit (SAMETO brand) and the preforms inserts in the hopper. After that, the elevator transfers the preforms to the horizontal elevator, the unscrambler and the final gravity guide (infeed rails).The below schematic diagram describes the general process of SBO10 machine: which consists of: 1. Preform infeed rails 2. Preform infeed wheel 3. Infrared oven 4. Preform transfer wheel 5. Blow wheel 6. Bottle transfer wheel 7. Bottle evacuation GENERAL Presentation 1. Infeed of cold preforms Cold preforms are inserted by an inclined ramp. They are hung by the neck and are guided by two rails between which they are lowered by gravity. 2. Preform heating linear oven The preforms, grasped in the spindles at the neck, are turned 180 degrees so that they are head down and are made to rotate as they pass in front of infrared lamps. The linear oven has 10 heating modules. Each oven module has 8 infrared lamps. Ath oven exit, an infrared camera reads the preform temperature so as the automatic regulation of all the areas coming under its control. 3. Hot preform transfer wheel A transfer wheel with 6 arms conveys the hot preforms through the blowing moulds when they leave the oven. 4. Preform ejection An ejection system is mounted after the preform transfer wheel, in case of a non correct temperature of a preform. 5. Blow wheel Preforms are put in the mould for which opening and closing are assured by a system of connecting rods operated by a cam. The mould is locked by a mechanical device. Blow nozzle guides the stretching rod, which ensures longitudinal orientation. A set of cameras synchronizes the whole process. The moulds are controlled for temperature by chilled water circulation. 6. Bottle transfer wheel A transfer wheel with 6 arms picks up the bottles in the moulds to evacuate them from the blowing wheel. 7. Bottle ejection An ejection system is mounted after the bottle transfer wheel. It is completed by a set of photocells. If the bottle is not correct, it is ejected. 8. Bottle outfeed wheel. An outfeed wheel with 8 notches receives the bottles comes from the transfer arms and puts them down on a belt. They are held by guides. The bottle outfeed can be linked to a conveyor system. - Hoisting and tipping unit (1996) - Hopper (1995) - Elevator (1995) - Orienting rollers (1995) - Unscrambler (1995) - Gravity rails (1995) - linear oven (1995) - Blow wheel with 10 moulds (1995) - Bottle outfeed wheel (1995) - Operator control panel (1995) - Electrical cabinets (1995) 12. Chiller (1998) Energy and fluid consumption 1. Electricity Max supplied power: 216kW Average consumption: 120 to 160 kW/h according to item Voltage: 380 (3phase) Frequency: 50/60 Hz Crsdoxlm Nyjpfx Ah Uei 2. Compressed air Supplied power: from 7 to 35 bar Control air pressure: 7 bar flow: 60 to 125 Nm3/h according to item Air quality: dry air, deoiled and filtered to 0,1 ppm Spherical base pressure: up to 25bar flow: 170 to 830 Nm3/h Free standing base pressure: up to 35 bars flow: 235 to 1.100 Nm3/h 3. Chilled water temperature: 10 to 12 celsium degrees pressure: 5 to 6 bars flow: up to 9 m3/h calories to be removed: up to 22.000 Kcal/hour Max supplied power: 216kW Voltage: 380 (3phas...

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. High Pressure compressor - KAESER Booster N 753 - G 13 bar / 40 bar" 4. Air Dryer 5. Receiver tank - Low pressure - MAX 16Bar Credsquuvrepfx Ah Uoi 6. Receiver tank - High pressure - MAX 45Bar

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, screw diameter: 90 mm, overall weight: 11,000 kg, total width: 3,200 mm, total length: 5,200 mm, total height: 2,200 mm, HDPE, PE extrusion blow molding machine (canisters, bottles). 4 units for sale. Compressors, chiller, and grinders are included with the machines. Crjdjxhg N Eepfx Ah Uji

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: Credpfsuiq Dhex Ah Uoi • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: ready for operation (used), A 13-layer blown film line Kuhne for the production of biaxially oriented high-barrier films is available. Film thickness range: 20µm-80µm, max. film width: 1400mm, max. output capacity: 400kg/h, extruders: 13 units, max. die head pressure: 500bar, flex ring die: 250mm/300mm, calibration tools: 200mm/225mm/250mm/280mm/300mm, yield: 80%-90%. Laminating films: sealing layer thickness: 25µm-35µm, printing layer thickness: 25µm-45µm. Monofilms: shrink lid thickness: 23µm-28µm, AF lid film thickness: 25µm-45µm, top and bottom film thickness: 75µm, balloon film thickness: 25µm-31µm. Documentation available. An on-site inspection is possible. Crsdpfx Ahew R Dh Ej Uoi

Condition: used, Semi-automatic PET bottle blowing machine Manufacturer: FERENC Type: F-1400 Manufacture date: 2006 Capacity: about 800 pcs / h Number of molds in the machine: 2 Codpfx Ajugu E Roh Usri Furnace dimensions: - length: 900 mm - width: 900 mm - height: 1200 mm Blower dimensions: - length: 1800 mm - width: 750 mm - height: 2000 mm Weight of the set: 1200 kg Technical condition: used machine

Condition: used, Year of construction: 2007, This is a Sidel SBO 4 blow moulder, it’s designed to receive preforms of 38 mm neck size caps and blow mould the bottles . The speed of the machine is at 6,000 bottles per hour on 2 litre round bottles . The year of manufacture is 2007 and the condition is very good. The is delivered with the pre forms hopper and elevator. Csdpfx Aow S Icish Uori Capacity: 6000 b/h Volumes: 250-500-1000-2000 ml Neck Size of preforms: 38 mm Format: Round bottles Air consumption: 11 bar Controls: SIEMENS SIMATIC MULTI TOUCH PANNEL Available: Immediately

Condition: ready for operation (used), overhauled and ready for production Crsdjxa Abbspfx Ah Usi

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Cjdpfx Ahjg Ailcj Ujri Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: good (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 2.065.0, clamping force: 200 kN, New digital control from BBM. Two sets of extruder heads (see attached pictures). Credew Dcybspfx Ah Uei

Condition: ready for operation (used), Year of construction: 2008, A SIG Corpoplast blow molding machine is available. Output: 21600 bottles/h, bottle formats: 500ml/750ml/1000ml/1500ml, max. blowing air pressure: 40bar, dimensions X/Y/Z: approx. 7000mm/4300mm/3100mm, weight: approx. 20000kg. Including preform feeder Transver AG, year of construction: 2008, silo, elevator, sorting and chute. Documentation available. On-site inspection is possible. Crodpfx Ahet Eu Azs Uei

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Credpewa Rhrefx Ah Uji Installed power: 150 kW Includes 1.5 L molds Preform feeder Technical condition: used machine, starts up, program is functional

Condition: used, functionality: fully functional, The SMF COMBI 400 is an automatic blow molder designed for the efficient and high quality production of PET bottles. This machine combines advanced technologies to offer continuous, accurate operation with minimal manual intervention, ideal for bottling plants requiring flexibility and performance. ADVANTAGES OF HS AND COMBI SERIES: • Low energy consumption • Modular construction • Silent work • Space saving, compact design • Easy change- overo f bottle size and types of neckrings • Advanced PLC control system with user friendly interface • Built-in memory of the PLC saves parameter sets required to produce different bottle sizes. • Pyrometric temperature measurement – Power Wizard KEY BENEFITS • Proven system working in hard environmental conditions • Powerful heading unit with precise controller and convenient adjusting mechanism • Minimum transfer space for the air distribution system • Simple, robust and durable operation MAIN PARAMETERS Blowing air quantity (25 BAR): 3.46 m3/h Crsdpfxswny Eio Ah Usi Mold material: FORTAL

Condition: new, new blow mold 2L & 3L for sale Cjdpjw Tcqksfx Ah Uori

Condition: good (used), Production capacity of up to 4000 b/h (depending on the format) For formats between 0,25lts up to 3lts Composed by: • Oven for heating the preforms composed of 6 heating modules with 8 infrared lamps each • Preform transfer Wheel Crodpfxswcggvj Ah Usi • Two-stage compressed air blowing body, low pressure pre-blowing and subsequent high pressure blowing. • Bottle transfer Wheel • Delivered with pallet turner. DOCUMENTATION AVAILABLE

Condition: reconditioned (used), Year of construction: 2012, SB 3000.5E linear blow molding machine, including: New modular heating system, Preform feeder, easy and quick mold change system, electric stretching system, touch screen panel, smooth performance adjustment, cracked bottle elimination function Single-nest machine prepared for blowing 5-liter bottles. The machine after a major renovation at Dynaplast, all operating components were replaced and the drive of the bottle ejection basket was changed, instead of the angular gear, a belt transmission with a servo drive was used, which allows for smoother operation of the component. The preform is also stretched using a belt transmission and driven by a servo drive, which allows for smooth speed adjustment from the operator panel, (we can smoothly adjust the speed of the stretching rods) The price given is for the machine without the mold visible in the photos, it is possible to resell the visible 5L mold Crjdpfxot Uap Ss Ah Usi

Condition: ready for operation (used), Year of construction: 2004, Two injection blow molding machines for hollow body production are available. 1) Injection blow molding machine Kautex KB 15.10, year of manufacture: 1984, overhaul: 2005, stations: 1, nozzle diameter: 80mm, clamping force: approx. 250kN, opening stroke: 300mm/800mm, max. mold thickness: 2x160mm, max. mold dimensions X/Y: 950mm/600mm, control: Siemens S7, operating hours: approx. 96432h. 2) Injection blow molding machine Kautex KB 50/13-S, year of manufacture: 1983, overhaul: 2003, nozzle diameter: approx. 80mm, clamping force: approx. 410kN, plate dimensions X/Y: 700mm/900mm, mold thickness: 2x320mm, opening stroke: 600mm/1300mm, control: Siemens S7. Documentation available. On-site inspection is possible. Crjdpfxewligwe Ah Uji

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 240, power: 60 kW (81.58 HP), Equipment: documentation/manual, Complete pellet plant consisting of wood grinder, sawdust pulverizer, pellet powder storage silos, pellet pressing machine plus conveyor belts, pellet collection silos and weighing system for bags or big bags. Complete plant with all automations Crjdpfx Ahjwiik Rs Uji

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes Cjdpfx Ahev Iflpe Usri 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: used, Year of construction: 2006, Semi-automatic PET bottle machine - ZENTRONIK ZR-7 1. Heating oven for heating PET preforms 2. Semi-automatic machine for the production of PET bottles Mould: two-cavity for 5.0 liter bottles Efficiency: approx. 800 bph Cjdpfx Ahswnzdao Uori Technical condition: used, functional

Condition: reconditioned (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: SB 8015, SB 8000 linear blow molding machine, serial number 8015, year of production 2006 with a nominal capacity of 7200 bph (approx. 6000 bph with a 2.0l bottle), Machine after general renovation, in very good technical condition, all operating components replaced. The machine set includes: Preform feeder, easy and quick mold change system, electric stretching system, mechanical lifting system, powered by electric motors for a closing system with pressure compensation, 6-inch touch panel, smooth regulation of capacity in the range of 5000-7400 bph, function of eliminating deformed molds and cracked bottles. Csdet T Txqopfx Ah Ujri The machine is adapted to the PCO 1810 preform, it is possible to retool the machine for another preform. The machine is sold without blow molds, we can make molds according to the customer's design adapted to our machine.

Condition: ready for operation (used), Year of construction: 2001, A complete 5-layer coextrusion blown film line with 5 extruders and all peripheral equipment is available. Total line dimensions X/Y/Z: 14m/22m/11m, blow head: Kiefel Worms FSBK 500 with IBC, die diameter: 500mm, film width range: 700mm-2000mm, haul-off width: 2000mm, winding width: 2000mm, line speed: 120m/min, melting capacity: 500kg/h, total power requirement: approx. 300kW. 1) Double winder Wintech, winding width: 2000mm, film thickness range: 35µm-150µm, max. roll diameter: 1000mm, max. roll weight: 1900kg, core inner diameter: 152mm/6inch. 2) Extruder Kiefel Worms 70.29D, power: 89kW, screw: 5-zone barrier screw, speed: 125rpm, renewed: 2010. 3) Adhesive extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 4) Center extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone core progressive screw, speed: 175rpm. 5) Adhesion promoting extruder Kiefel Worms 50.25D for the outer layer, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 6) Kiefel Worms 80.25D outer layer extruder, power: 125kW, screw: 5-zone barrier screw, speed: 150rpm. 7) Reinhold SRK 200/9.6 film calibrating device. The entire line is controlled by a Plast Control system. Further components: integrated width measurement, C-scan for profile measurement, web center control, corona pre-treatment, film pre-draw. Including a replacement FSBK 5-layer blow head with IBC, replacement rollers, annular gap blower with filter, suction units, crane and external system terminal. Documentation available. On-site inspection is possible. Csdpfxsv T An So Ah Ueri

Condition: excellent (used), Year of construction: 2003, PET bottle blowing machine Manufacturer: KRONES Model: CONTIFORM K781 Crodpovddkvofx Ah Uei Efficiency: 12,000 bph Includes 1.5 L and 0.5 L bottle molds Power: 150 kW Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Set dimensions (blow mold + preform feeder): 1100 x 340 cm, h: 450 cm Blow mold dimensions: 500 x 340 cm, h: 250 cm Feeder dimensions: 600 x 250 cm, h: 450 cm Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Year of production: 2003 Technical documentation of machine operation Very good condition