Condition: new, Year of construction: 2025, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability, is equipped with an automatic blade tension sensor. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 260 x 140 Ffodpeudi Unjfx Agdst 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Condition: used, Year of construction: 1997, saw band length: 4,150 mm, - Vertical bandsaw with double-sided mitre capability - Hydraulic feed through the cut - Hydraulic material clamping - Minimum quantity lubrication system - Digital mitre angle display ELGO Fjdox Saurepfx Agdsft - Including roller conveyor (partially driven) before and after the saw

Condition: used, Year of construction: 2007, Small panel saw Behringer LPS 60 T, year 2007, available from early 2026. Ffedpfx Agex H Rulodst

Condition: good (used), Year of construction: 1987, Saw blade Ø: 400 mm Cutting range round: 130 mm Ffsdpfx Aox Ir Rwjgdot Rectangular: 305 x 40 mm Mitre cut at 45° round: 130 mm Rectangular: 245 x 40 mm 2 cutting speeds via pole-switchable motor: 9 and 18 m/min Feed rate hydraulically steplessly adjustable: 0 - 1000 mm/min Saw drive: 380 V, 1.7/2.6 kW Weight approx.: 800 kg Space requirement without roller conveyor: 1100 x 1000 x 1900 mm

Condition: new, Year of construction: 2025, Machine type: Bandsaw - semi-automatic Band dimensions: 3055 x 27 x 0.9 mm Cutting capacity (rectangular): 200 x 350 mm Cutting capacity (round): 260 mm Cutting speed: 18 - 87 m/min Main drive motor power: 1.5 kW Weight: approx. 460 kg Dimensions (W x D x H): approx. 1700 x 1200 x 1600 mm Standard equipment: - Infinitely variable cutting speed control via control panel with display - Raising/lowering via control panel (hydraulic) - Manual vice, quick-clamping and lengthwise adjustable - Material stop - Emergency stop on control panel - Brush for band cleaning - Coolant tank: 17 litres - Manual in English Options: - 2 pieces of standard 2-meter roller conveyor without measuring scale - 1 band saw blade 3,055 x 27 x 0.9 mm Ffodpfox Narljx Agdot

Condition: good (used), Year of construction: 1995, functionality: fully functional, For sale: Emmegi TU/4 double head cutting-off machine, year 1995. A reliable and simple two-head saw for cutting aluminium and PVC profiles. Ideal for window & door manufacturers and general profile fabrication. Fodpoxz R Npjfx Agdoft Specifications Double head mitre saw Blade diameter approx. 350 mm (Ø300–400 mm) Cutting angles 90° and 45° Cutting length approx. 3–4 m Pneumatic horizontal clamps Motor power ~1.5–2.2 kW per head Bobmt Dtyexz R Npo Aolb Spindle speed approx. 3000 rpm Weight approx. 500–600 kg 400 V / 6–8 bar Machine is in working condition and ready for use. Please verify the accuracy of the machine specifications with the seller.

Condition: new, Year of construction: 2025, Professional, very powerful and efficient band saw for metal with 45° swivel arm. The perfect solution for ironwork, production and craft workshops. Unparalleled for many years, the design and solid construction make it a perfect solution. Machine description Professional, very powerful and efficient metal band saw with 45° swivel arm, CORMAK BS 712 SW is based on refined solutions making it unrivaled in its class. Arm made of shaped spheroidal cast iron ensures rigidity during operation and absorbs all vibrations. Control panel is located on the arm of the cutter. It features high efficiency and simple handling. Provides cutting in vertical plane and in the plane perpendicular to the axis of the cut material, or at any angle in 45° – 90° range. Element cut can be fed manually or by any feeding device. The feed during cutting is gravitational on the principle of oil flow in a two-chamber hydraulic cylinder. Suitable speed of arm lowering is obtained thanks to the valve controlling oil flow between hydraulic cylinder chambers. Rugged, stable and refined construction as well as the arm made of uniform cast iron provide high rigidity and stability while cutting, ensuring accuracy and long-term reliability. The design of the 20 mm saw blade used in the machine makes it possible to cut large quantities of elements. Required band linear velocity is obtained by changing the ratio on the belt pulley between the worm gear and the driving motor. Technical data Motor power 1.1 kW Band speeds 22/33/45/65 m/min Power supply 400V Band dimensions 2360×20×0.9 mm Cutting range 45°L – 45°R Weight 145 kg Dimensions 1280x575x1140 mm Angle 0°.....Ø 205.....215×205.....205×205 45° L.....Ø 150.....100×200.....130×130 45° R.....Ø 140.....140×90.....90×90 The price is a net price. Price does not include shipping costs. Fedpfx Ajw U Skvjgdoft For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, CORMAK BS530H Metal Band Saw – A Professional Tool for Cutting Pipes and Profiles The CORMAK BS530H metal band saw is an efficient semi-automatic bandsaw designed for precise cutting of steel elements, pipes, and profiles at various angles. Its solid cast-iron construction, reinforced blade guidance system, and advanced hydraulics make it ideal for serial production and demanding industrial environments. The integrated control panel allows a single operator to manage all functions, significantly reducing operation time and improving workplace ergonomics. Key Advantages of the Machine Semi-automatic operation – hydraulic arm lifting/lowering and vise control via control panel. Worm gearbox with bronze components ensures smooth, vibration-free, and precise operation. Stepless cutting speed adjustment from 20 to 70 m/min – suitable for various materials. Carbide and ball-bearing blade guides for durability and precise blade tracking. Quick-release vise, manually or hydraulically controlled, adjustable left/right. Miter cutting range from -45° to +60° with precise angle scale reading. Heavy-duty cast-iron frame ensures cutting stability and long machine life. Hydraulic feed rate control with adjustable return height of the saw arm. Construction and Technology The BS530H model features a reinforced drive system and industrial-grade hydraulics, ensuring reliable performance under intensive use. The massive frame construction minimizes vibration and ensures consistent cutting performance. An ergonomic control panel allows full process control from one location. The coolant system, integrated into the base, efficiently removes heat and debris, protecting the blade from overheating. Cutting Precision and Efficiency With stepless speed control, manual or semi-automatic operation modes, and a dial gauge blade tension meter, the BS530H delivers repeatable, high-quality cuts, even in long production runs. A material support roller and arm lock after the cutting cycle enhance operational safety and efficiency. Applications The CORMAK BS530H is dedicated to industrial production facilities, metalworking shops, and companies performing serial cutting of profiles, pipes, and solid steel sections. It’s ideal for serial manufacturing, prefabrication, and component preparation for welding or further processing. Standard Equipment Control console with semi-automatic functions Hydraulic vise Blade cleaning brush Coolant system with pump Front material roller Dial gauge blade tension meter CE certificate and technical documentation (DTR) Technical Specifications: Parameter Value Working height 965 mm Cutting speed 20 – 70 m/min Blade dimensions 3770 × 34 × 1.1 mm Coolant system power 0.1 kW Total power 3.0 kW Power supply voltage 400 V Dimensions (W × D × H) 2200 × 1400 × 2050 mm Weight 730 kg Fodpfxsw U Svle Agdoft

Condition: new, Year of construction: 2025, The CORMAK H - 280 SA column band saw is a highly efficient machine for cutting bars, pipes and profiles made of steel, cast iron and non-ferrous metals in an automatic cycle. The solid body and strong frame of the saw, combined with the column construction, provide excellent rigidity and an exceptional level of stability during the cutting process of even the most difficult metals to machine. The cutter is equipped with a PLC controller and an easy-to-use touch screen. Automatic band saw work on manual and automatic modes. Manual mode allows you to perform all activities manually from the machine's desktop. Automatic mode - after switching on the machine, the entire cutting cycle, i.e. fixing the cut detail in the vice, its shift to a specific dimension to the cutting tape, leaving the arm to cut and its raising to the desired height after finished cutting takes place without the operator's operation. Cutting parameters, such as the number of pieces of cut details, their dimensions, the speed of the cutting band, the speed of the arm's descent, are set on the control panel. The device automatically stops when the series is cut, the cutting band breaks or another failure identified by the cutter's control system is detected. The body of the machine is a cast iron set on a rigid, spatial plate structure of the casing. Inside the housing there are: a hydraulic unit, a coolant tank with a pump and a chip feeder. The drive of the cutting band based on an inverter-controlled motor ensures smooth regulation in a large range of speeds. The hydraulically forced lowering of the arm is regulated in a wide range by a precise throttle valve. The fast feed system allows you to shorten the time of cutting individual elements. Hydraulic material feeding system ensures a fully automatic working cycle of the machine. The controller equipped with an LCD display allows you to program the operation of the saw, signals the end of the material, communicates errors and informs about the number of cut sections after the programmed time. The maximum material feed length in one stroke is 500 mm with an accuracy of +/- 0.2 mm per stroke. Innovativeness and production of CORMAK semi-automatic and automatic series cutters according to norms and standards compliant with ISO:90001 and ISO:140001 certificates, guarantee safety, quality and product reliability. The use of motors licensed by a well-known and respected manufacturer on the global market, one of the world's leaders, ABB, guarantees long and trouble-free operation. Technical data Cut range Ø280 or 280 x 280 Band saw blade 3505 x 27 x 0.9mm Cut speeds 40/60/80 m/min. Engine 3kW Hydraulic power pack 0.75kW Coolant pump 0.09kW Feeder pitch 500mm Load capacity 1500 kg Dimensions 1750x1900x1550mm Weight 1100 kg Max. cutting range angle 0º ø280 280 × 280 Standard equipment work in automatic cycle arm position memory function built-in hydraulic unit vise position memory function change cutting speed motorized belt cleaning brush cooling system Ffjdeiz S Nyspfx Agdot bi-metal band saw CE Declaration of Conformity Manual in Polish and English For more information visit our web page

Condition: new, Year of construction: 2025, CORMAK HBS320 band saw for metal provides cutting at any angle from -45° to + 60°. The element cut can be fed manually or by any feeding device. The feed during cutting is gravitational on the principle of oil flow in a two-chamber hydraulic cylinder. Band saw perfect for cutting tubes, profiles and other materials. Machine characteristics CORMAK HBS320 band saw for metal provides cutting at any angle from -45° to + 60°. The element cut can be fed manually or by any feeding device. The feed during cutting is gravitational on the principle of oil flow in a two-chamber hydraulic cylinder. Band saw perfect for cutting tubes, profiles and other materials. Operator starts the machine by pressing the START button and sets cutting speed. After the cycle is finished the machine automatically stops and the operator lifts the arm to the starting position. The band saw arm is made of massive, uniform cast iron, and together with 27 mm wide cutting band enables high quantity cutting of structural steel, stainless steel and tools. The vice is located in an adjustable bed and equipped with a quick clamp. Blade guides are equipped with a ball bearings system and cemented carbides, ensuring excellent cutting precision and straight cut. It has a huge impact on the band guiding, its durability, accuracy and cutting quality. The carbide guiding drastically reduces the wear of both the machine and the blade. The base is enclosed, constituting a rigid welded body of steel sheets. A separate flood coolant container with an electropump is inside. The shape of the base upper part constitutes a tank for flood coolant draining and chips produced during cutting. Cast iron workbench is attached to the base, with a double-sided swivel arm and a control panel. The feed speed is controlled by the control panel. There are 2 cutting band speeds: 44 and 88 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Ø max 260 mm /perpendicular cutting H×B max 320×160 mm /perpendicular cutting Power supply - 3–phase, 400V Total power - 1,5 kW Arm lowering control - hydraulic cylinder Ffsdpfx Agji D Dgwjdot Band dimensions - 2740×27×0.9 mm Band speed - 44 / 88 m/min Vice base height - 920 mm Dimensions - 1400×880×1550 mm Weight - 280 kg Cutting parameters Angle 0º ---- ø260 320×160 255×255 45º R ø210 210×200 210×210 60º R ø135 135×130 130×130 45º L ø160 220×130 160×160 The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, The CORMAK H-350SA column band saw is a high-performance machine for cutting solid workpieces and profiles in an automatic cycle. Robust body and sturdy saw frame in combination with the column structure ensure excellent rigidity and exceptional stability during cutting even the most difficult-to-cut metals. The cutting-off machine is equipped with PLC control and an easy-to-use touch screen. The undoubted advantage of Ffodswdunwepfx Agdjt The unquestionable advantage of this model is its swivel head which allows cutting in the following ranges 0°- 60° - in automatic cycle as well as semi-automatic - infinitely adjustable angle. angle adjustment. Manual and Automatic mode: The cutting-off machine allows both manual operations from the machine control panel in manual mode and an automatic cutting cycle in automatic mode, eliminating the need for constant operator assistance. Vise top pressure: The cutting machine is adapted to package cutting Automatic Cutting Cycle: In automatic mode, the entire cutting process, including clamping the workpiece, moving it to the specified dimension, lowering the cutting arm and raising it after the cut is completed, is carried out without operator intervention. Panel Controlled Parameters: Cutting parameters such as number of pieces, workpiece dimensions, belt speed, and more, are set and controlled via a control panel with an easy-to-use touchscreen. Robust Construction: The machine body is made of cast iron set on a rigid, space-age slab chassis structure for exceptional rigidity and stability. Cutting belt drive: A powerful three-speed motor, hydraulic belt tension and cooling system and cleaning brush contribute to precise and efficient cutting. Safety System: If the cutting belt breaks, the machine stops automatically, increasing operator safety. Hydraulic Material Feeding System: This system allows the machine to cycle fully automatically, with precise setting of the material feed length. Innovation and ISO Standards: Cormak provides innovative solutions and production in accordance with ISO:90001 and ISO:140001, which demonstrates the high quality, safety and reliability of the product. Technical data: Cutting range Ø350 or 350 x 350 Belt 4515 x 34 x 1.1 mm Cutting speeds 27/45/69 m/min. Total power 4.8kW Hydraulic power pack 0.75kW Coolant pump 0,04kW Belt tensioning hydraulic Feeder stroke 500 mm Load capacity 1500 kg Table height 700 mm Dimensions 2800 x 2200 x 1700 mm Weight 1500kg

Condition: new, Year of construction: 2025, Semi-automatic CORMAK S440R band saw. Its arm is made of uniform cast iron and, together with a 34 mm wide cutting band, it enables cutting various profiles and shapes. The band saw uses a vice and a hydraulically raised and lowered arm. Machine features Semi-automatic band saws, after being switched, do the whole cutting cycle automatically, i.e. clamp the cut material in the hydraulic vice, switch on the cutting band, lower the cutting arm (adjustable speed), stop the machine after cutting, raise the arm up (adjustable arm height) and switch the hydraulic vice off. Machine's arm is made of uniform cast iron and, together with a 34 mm wide cutting band, it enables cutting various profiles and shapes. The band saw uses a vice and a hydraulically raised and lowered arm. Technical data Minimum cutting diameter Ø 5 mm Ffedpfoi Dx R Njx Agdjt Minimum material length in vice 30 mm Vice base from ground distance 780 mm Cutting band dimensions 5200×34×1.1 mm Total power 4.4 kW Band speed 20/90 m/min Dimensions (L×W×H) 2500×1900×1450 mm Weight 1100 kg Max. cutting range [mm] Angle 0º ø450 620×440 610×440 450×450 45º R ø440 500×190 360×440 420×420 45º L ø440 510×180 460×390 390×390 60º R ø330 330×170 170×440 300×300 60º L ø350 350×170 330×310 310×310 Standard equipment PLC controller Semi-automatic operating cycle Control console on a separate component Control panel with an LCD display Built-in hydraulic unit Hydraulic control of arm motion (up – down) with possibility of smooth lowering speed control Arm position memory function (arm returns to a defined height after cutting) Hydraulically controlled vice's jaws (long stroke cylinder with position memory) Cutting at angles of L/R 60o – 45o – 0o – 45o – 60o Digitally displayed set cutting angle Smooth band speed adjustability (inverter) Powered brush for cleaning the band Cooling system Bi-metal saw blade EC Declaration of Conformity User manual For more information please visit our web page or contact us.

Condition: new, Year of construction: 2025, Powerful, reliable and modern semi-automatic band saw for metal with automatic arm raising and lowering. The arm is rotational in both ways. The machine is fantastic for ironworking, e.g. cutting tubes and profiles. Product features CORMAK S-200RH band saw is by default equipped with automatic arm lowering and raising as well as with a precise arm height regulator. Due to an automatic hydraulic damper, the manual handling of the machine has been simplified to feed and clamping the cut material in a vice. The arm made of uniform iron casting, together with a refined, solid and stable construction, ensure S-200R's exceptional rigidity, resulting in failure-free handling and high cutting precision. The innovativeness and production of semi-automatic and automatic series "CORMAK-PREMIUM LINE" band saws, compliant with the norms and standards consistent with ISO:910001 and ISO:140001 certificates, warrant safety, quality and reliability of the product. M3V motors from ABB, a renowned worldwide manufacturer, warrant long-term reliability. As an official and the only representative on the Polish market, we assure that the product is original and provide professional, customised warranty and post-warranty services. Technical data Type - semi-automatic Arm raising and lowering - hydraulic with smooth arm lowering control Band speed - 36/70 mm/min Angled cutting - left to 45°, right to 60° Vice - hydraulic Minimum cutting diameter - Ø 5 mm Minimum material length in vice - 30 mm Vice base height - 780 mm Cutting band dimensions - 27×0.9×2910 mm Total power - 2.1 kW Dimensions (LxWxH) - 1600×800×1400 mm Weight - 530 kg Angle Ffsdpfx Agoi D D A Sedst 0º -----ø250 320×240 240×240 45º L ø200 220×120 190×190 45º P ø220 235×120 210×210 60º P ø110 155×110 100×100 Default equipment Control panel on separate component Built-in hydraulic unit Hydraulic control of arm motion (up – down) with possibility of smooth lowering speed control Arm position memory function (arm returns to a defined height after cutting) Cutting at angles of L/R 45° - 0° - 45° - 60° Brush for cleaning band Cooling system Bi-metal band saw EC Declaration of Conformity User manual The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, CORMAK H-50/70 is a highly efficient column band saw for semi-automatic cutting of steel profiles, cast iron and non-ferrous metals. Its column design ensures rigidity during cutting, and employment of a completely different arm guiding technology than in pivot band saws provides cutting time reduction and accuracy increase. Machine description CORMAK H-50/70 is a highly efficient column band saw for semi-automatic cutting of steel profiles, cast iron and non-ferrous metals. Its column design ensures rigidity during cutting, and employment of a completely different arm guiding technology than in pivot band saws provides cutting time reduction and accuracy increase. Ffjdpfx Agsizi T Eodjt CORMAK H-50/70 semi-automatic band saws, after being switched on, do the whole cutting cycle automatically, i.e. clamp the cut material in the hydraulic vice, switch on the cutting band, lower the cutting arm (adjustable speed), stop the machine after cutting, raise the arm up (adjustable arm height) and switch the hydraulic vice off. Manual handling of the machine is simplified to feeding material towards the bumper. Solid uniform cast iron arm along with the refined, stable design ensure that CORMAK H-50/70 is rigid and reliable, providing very precise cutting. Hydraulic band tension provides optimum cutting. In the case of band breakage the machine stops automatically. Precise guiding of the band is ensured by guides with bearings and cemented carbide inserts. The innovativeness and production of semi-automatic and automatic series "CORMAK-PREMIUM LINE" band saws, compliant with the norms and standards consistent with ISO:910001 and ISO:140001 certificates, warrant safety, quality and reliability of the product. M3V motors from ABB, a renowned worldwide manufacturer, warrant long-term reliability. Technical data Type Semi-automatic Arm raising and lowering Hydraulic, with stepless lowering adjustment Band speed 26/41/66 m/min Vice Hydraulic Cutting band dimensions 41×1.3×6430 mm Total power 8 kW Dimensions 3200×1100×2100 mm Weight 2900 kg Maximum cutting range [mm] Angle 0º ø500 500×700 Default equipment Control panel at the front of the machine Semi-automatic work Built-in hydraulic unit Arm position memory function Brush for cleaning the band Hydraulic band tension Semi-automatic work Hydraulic band tension Cooling system Bi-metal cutting band EC declaration of conformity User manual

Condition: new, Year of construction: 2025, The CORMAK H - 260SA column band saw is a highly efficient machine for cutting bars, pipes and profiles made of steel, cast iron and non-ferrous metals in an automatic cycle. The solid body and strong frame of the saw, combined with the column construction, provide excellent rigidity and an exceptional level of stability during the cutting process of even the most difficult metals to machine. The cutter is equipped with a PLC controller and an easy-to-use touch screen. Automatic band saw work on manual and automatic modes. Fsdpfoiz S I Hjx Agdsft Manual mode allows you to perform all activities manually from the machine's desktop. Automatic mode - after switching on the machine, the entire cutting cycle, i.e. fixing the cut detail in the vice, its shift to a specific dimension to the cutting tape, leaving the arm to cut and its raising to the desired height after finished cutting takes place without the operator's operation. Cutting parameters, such as the number of pieces of cut details, their dimensions, the speed of the cutting band, the speed of the arm's descent, are set on the control panel. The device automatically stops when the series is cut, the cutting band breaks or another failure identified by the cutter's control system is detected. The body of the machine is a cast iron set on a rigid, spatial plate structure of the casing. Inside the housing there are: a hydraulic unit, a coolant tank with a pump and a chip feeder. The drive of the cutting band based on an inverter-controlled motor ensures smooth regulation in a large range of speeds. The hydraulically forced lowering of the arm is regulated in a wide range by a precise throttle valve. The fast feed system allows you to shorten the time of cutting individual elements. Hydraulic material feeding system ensures a fully automatic working cycle of the machine. The controller equipped with an LCD display allows you to program the operation of the saw, signals the end of the material, communicates errors and informs about the number of cut sections after the programmed time. The maximum material feed length in one stroke is 500 mm with an accuracy of +/- 0.2 mm per stroke. Innovativeness and production of CORMAK semi-automatic and automatic series cutters according to norms and standards compliant with ISO:90001 and ISO:140001 certificates, guarantee safety, quality and product reliability. The use of motors licensed by a well-known and respected manufacturer on the global market, one of the world's leaders, ABB, guarantees long and trouble-free operation. Technical data Cut range Ø260 or 260 x 260 Tape 3150 x 27 x 0.9mm Cut speeds 40/60/80m/min Engine 2.2kW Hydraulic power pack 0.75kW Coolant pump 0.09kW Feeder stroke 500mm Load capacity 1500 kg Dimensions 1600 x 1800 x 1550mm Weight 1000 kg Max. cutting range angle 0º ø260 260 × 260 Standard equipment work in automatic cycle arm position memory function built-in hydraulic unit vise position memory function change cutting speed motorized belt cleaning brush cooling system bi-metal band saw CE Declaration of Conformity Manual in Polish and English For more information visit our web page

Condition: new, Year of construction: 2025, The CORMAK HBS260 band saw for cutting pipes, profiles and bars is widely used in all locksmith workshops where precision, quality and cutting speed are important. The model is equipped with a 0-60° swiveling arm. The frame design ensures accurate and quiet operation. It has a removable filing tray for easy cleaning! Machine characteristics A horizontal metal band cutter with a swiveling arm allows cutting in a plane perpendicular to the axis of the material being cut and at any angle ranging from 0 to 60°. The material to be cut can be fed manually or with any mechanical device, and the tool feed is automatic. The tape guides are equipped with special carbide plates and bearings. This has a huge impact on the belt guidance, its life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and saw blade. The machine is equipped with an efficient cooling pump with a closed coolant circuit. The cutter's arm made of uniform cast iron together with the 27 mm wide cutting band used in this cutter allows it to fully perform multi-series cuts of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The saw blade guides are equipped with hard metal plates - sintered carbides and a rolling bearing system. It is the CENTRED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The shape of the upper part of the base constitutes a bathtub for draining coolant and catching chips generated while cutting the material. A cast iron work table with a swivel arm and a control panel on a separate arm is attached to the base. In the cutting process, the main cutting movement is the movement of the cutting band and the falling feed of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic actuator. The feed speed is regulated on the cutter's control panel. We can choose from two cutting band speeds: 35 and 70 m/min. In the lower position of the arm (after cutting the material), the cutting belt drive is turned off automatically. Safety is ensured by the cutting band covers and micro switches that stop the engine after the cutting cycle is completed or any of the covers are opened. Additional protection consists in automatic shutdown of the cutter in the event of the cutting band breaking. Cutting band size [mm] 2520 x 27 x 0.9 Tape tension mechanical (manual) Belt speeds [m/min] 35, 70 Adjustable arm drop stepless - hydraulic actuator Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame tilt [°] 0-60 Fjdpfx Agoudi Uzodoft Power supply 3 phases 400V Main engine power [kW] 1.1/1.5 Cooling pump motor power [kW] 0.05 Dimensions with base [cm] 150x80x140 Weight [kg] gross/net - 210 / 180 kg Additionally 2 M42 saw blades 5L Emulsol ZW580 magnetic chip collector

Condition: new, Year of construction: 2025, Cormak S200R Manual band saw for cutting in large industrial facilities. Features high accuracy metal cutting, even at 45º/60º. Machine features CORMAK S-200R MANUAL band saw with EC declaration, provides cutting metal at any angle from -45° to + 60°. The element cut can be fed manually or by any feeding device. The feed during cutting is gravitational on the principle of oil flow in a two-chamber hydraulic cylinder. Appropriate arm lowering speed is ensured by a valve controlling oil flow between the chambers. Operator starts the machine by pressing the START button and sets cutting speed. After the cycle is finished the machine automatically stops and the operator lifts the arm to the starting position. Material is fed manually. This model is used in both low and high quantity production, and due to its solid construction allows for cutting various materials, including stainless steel, tool steel and profiles. The machine provides cutting at an angle due to rotary arm. The band saw arm is made of uniform cast iron, and together with 27 mm wide cutting band enables high quantity cutting of various materials. The vice is located in an adjustable bed and equipped with a quick clamp. Blade guides are equipped with a ball bearings system and cemented carbides, ensuring excellent cutting precision and straight cut. The arm is equipped with an automatic blade tension sensor, at a 25° angle, thus increasing blade's durability. There is a blade cleaning brush attached to the bottom of the arm. Machine drive is transmitted through a worm drive filled with gear oil. The machine is equipped with a three-phase motor with double winding and two cutting speeds. The motor is thermally protected. Two cutting band speeds: 35 and 70 m/min. The construction: the arm, the vice and the rotating table are iron castings. Closed cooling system. The machine is equipped with a bumper with a ruler for setting the length of material cut. The base of the machine is a rigid cuboid made of steel sheets in which a fluid container with a flood coolant pump is located. Safety during cutting ensures an electrical system that meets all EC requirements. The machine is equipped with a limit switch which stops the machine after a cutting process is finished, an emergency button, and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened Technical data Type gravitational Arm raising and lowering gravitational with stepless arm lowering adjustment Band speed 36/70 m/min Cutting at an angle from 45° left up to 60° right Vice manual Minimum cutting diameter Ø 5 mm Minimum material length in vice 30 mm Vice base height 890 mm Cutting band dimensions 27×0.9×2910 mm Total power 2.1 kW Dimensions (LxWxH) 1600×800×1400 mm Weight 500 kg Max. cutting range [mm] Angle 0º ø250 320×240 240×240 45º L ø200 220×120 190×190 Fodpfx Agjfy Ttiodjft 45º P ø220 235×120 210×210 60º P ø110 155×110 100×100 For more information please visit our web page or contact us

Condition: new, Year of construction: 2025, functionality: fully functional, Band saw for metal with optimal cutting range, commonly used in carpentry, production and craft facilities. Machine description CORMAK BS 128HDRC band saw for metal with optimal cutting range, designed for professional craftsmen, distinguished by efficiency and easy handling. Arm swivelling in both directions is a very big advantage in angled cutting. Despite small dimensions, its big weight (103 kg) makes it very stable and vibration-free during cutting larger materials. Element cut can be fed manually or via feeding machines. Feed during cutting is gravitational, with oil flow in a two-chamber hydraulic cylinder. Arm lowering control is ensured by a valve controlling oil flow between chambers of cylinder. Straight cut is achieved by a set of bearings guiding the band. Machines are equipped with a limiting switch and ON/OFF switch compliant with IP54. Swivelling saw frame for double bevelling within -45o - + 60o. Technical data Cutting band size 1640×13×0.65 mm Cutting speed 23/34/54 m/min Power 0,55 kW/230V Arm lowering control stepless, through hydraulic cylinder Cutting range -45° - + 60° Dimensions 942×442×548 mm Weight 103 kg Maximum cutting range [mm] Angle 0°.....ø125 mm.....100×150 mm....100×100 mm -45°.....ø90 mm.....90×75 mm.....90×90 mm +45°.....ø90 mm.....90×75 mm.....90×90 mm +60°.....ø55 mm.....55×55 mm.....55×55 mm Fodpfx Agswq A Dysdoft Default equipment 3rd generation hydraulic cylinder Table for vertical cuts Quick-clamping vice Coolant system Workpiece limiter - bumper Automatic limiting switches Modern thermal engine protection Mobile base with four wheels User manual The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, The CORMAK HBS260 band saw for cutting pipes, profiles and bars is widely used in all locksmith workshops where precision, quality and cutting speed are important. The model is equipped with a 0-60° swiveling arm. The frame design ensures accurate and quiet operation. It has a removable filing tray for easy cleaning! Machine characteristics A horizontal metal band cutter with a swiveling arm allows cutting in a plane perpendicular to the axis of the material being cut and at any angle ranging from 0 to 60°. The material to be cut can be fed manually or with any mechanical device, and the tool feed is automatic. The tape guides are equipped with special carbide plates and bearings. This has a huge impact on the belt guidance, its life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and saw blade. The machine is equipped with an efficient cooling pump with a closed coolant circuit. The cutter's arm made of uniform cast iron together with the 27 mm wide cutting band used in this cutter allows it to fully perform multi-series cuts of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The saw blade guides are equipped with hard metal plates - sintered carbides and a rolling bearing system. It is the CENTRED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. Fedpfx Agjmrnk Ejdjft The shape of the upper part of the base constitutes a bathtub for draining coolant and catching chips generated while cutting the material. A cast iron work table with a swivel arm and a control panel on a separate arm is attached to the base. In the cutting process, the main cutting movement is the movement of the cutting band and the falling feed of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic actuator. The feed speed is regulated on the cutter's control panel. We can choose from two cutting band speeds: 35 and 70 m/min. In the lower position of the arm (after cutting the material), the cutting belt drive is turned off automatically. Safety is ensured by the cutting band covers and micro switches that stop the engine after the cutting cycle is completed or any of the covers are opened. Additional protection consists in automatic shutdown of the cutter in the event of the cutting band breaking. Cutting band size [mm] 2520 x 27 x 0.9 Tape tension mechanical (manual) Belt speeds [m/min] 35, 70 Adjustable arm drop stepless - hydraulic actuator Vice base height [mm] 860 Saw wheel diameter [mm] 300 Saw frame tilt [°] 0-60 Power supply 3 phases 400V Main engine power [kW] 1.1/1.5 Cooling pump motor power [kW] 0.05 Dimensions with base [cm] 150x80x140 Weight [kg] gross/net - 210 / 180 kg *Please note that machine is sold without CEE connector by default, since there are many different types of it. If you would like to receive it with the machine, please write it to the seller before making a purchase/during order proceeding. The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, functionality: fully functional, CORMAK C33 column band saw is an incredibly efficient machine in automatic cutting of tubes, steel and cast iron profiles as well as non-ferrous metals. Rugged body and strong frame of the saw ensure great rigidity and stability during cutting even the toughest metals. Technical data Type automatic column Arm raising and lowering hydraulic with smooth control Band speed 20–100 m/min Steady and feeding vice hydraulic Minimum cutting diameter Ø 5 mm Minimum material length in vice 30 mm Ffodperh Epkefx Agdot Vice base height 780 mm Cutting band 34×1.1×4115 mm Main motor power 4.4 kW Hydraulic unit power 1.5 kW Coolant fluid pump power 0.75 kW Dimensions (L×W×H) 2300×1780×1650 mm Weight 1900 kg Max. cutting range Angle round square 0º ø300 300×400 Default equipment Automatic cycle operation Touchscreen LCD control panel Programming numbers and lengths of cut details Possibility of storing 5 various cutting macros Electronic display of band speed Arm position memory function Built-in hydraulic unit Vice position storage function Smooth cutting speed adjustment (motor with an inverter) Powered brush for cleaning the band Cooling system Bi-metal saw blade EC Declaration of Conformity User manual For more information visit our web page

Condition: new, Year of construction: 2025, CORMAK HR500SA is an advanced automatic band saw designed for cutting solid materials, pipes and steel profiles with large cross-sections. Thanks to its two-column design and reinforced frame, the machine provides the highest stability, precision and repeatability of cutting - even in continuous operation. Technical data: automatic band saw HR500SA Cutting range Ø500 mm or 650 x 500 mm Band dimensions 6600 x 41 x 1.3 mm Band speeds 27 / 45 / 69 m/min Total power 6.5 kW Band tensioning manual Feeder stroke 500 mm Table height 715 mm Fjdpei Ab Dlofx Agdoft Load capacity 3000 kg Dimensions (L x W x H) 3200 x 3050 x 2115 mm Weight 3200 kg Standard equipment touch control panel with settings memory, automatic work cycle, top package pressure, hydraulic material feeding system, three-speed cutting gear, cooling system and cleaning brush, bimetallic cutting band, declaration of conformity CE, DTR instruction.

Condition: new, Year of construction: 2025, A strong, big band saw for metals with a swivel arm, enabling cutting in the plane perpendicular to the axis of the cut material and at any angle from -45° (left) to + 60° (right). Band saws are perfect for cutting tubes, profiles and other materials. Fjdpsi D Ddisfx Agdoft Product features Material cut can be fed manually or by any feeding device, with automatic tool feed. Appropriate cutting speed (band speed) is obtained through a change on a control panel. Rigid construction arm is made of profiled cast iron. The drive from the electric motor directed to the cutting band driving wheel is transmitted by a motor with worm drive. The cutting band is tensioned on two cast iron wheels with a manual tightener and guided by adjustable rolling and linear carbide guides. The base is enclosed, constituting a rigid welded body of steel sheets. A separate flood coolant container with an electropump is inside. The shape of the base upper part constitutes a tank for flood coolant draining and chips produced during cutting. Cast iron workbench is attached to the base, with a -45° to + 60° swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds: 36 and 72 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Cutting band size - 2720×27×0.9 mm Band tension - mechanical (manual) Band speed - 36, 72 m/min Arm lowering control - stepless – hydraulic cylinder Vice base height - 765 mm Minimum material length in vice - 100 mm Power supply - 3-phase, 400 V Total power - S1 100%: 1.5; S6 40%: 2.1 Cooling pump motor power - 0.025 kW Weight - 370 kg Warranty - 12 months User manual - yes CE declaration - yes Angle 0° --- ø250 310×210 240×240 45° R ø200 200×140 180×180 45° L ø165 185×145 160×160 60° R ø120 120×95 100×100 The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, Band saw for metal with optimal cutting range, commonly used in carpentry, production and craft facilities. Machine description CORMAK BS 128HDRC band saw for metal with optimal cutting range, designed for professional craftsmen, distinguished by efficiency and easy handling. Arm swivelling in both directions is a very big advantage in angled cutting. Despite small dimensions, its big weight (103 kg) makes it very stable and vibration-free during cutting larger materials. Element cut can be fed manually or via feeding machines. Feed during cutting is gravitational, with oil flow in a two-chamber hydraulic cylinder. Arm lowering control is ensured by a valve controlling oil flow between chambers of cylinder. Straight cut is achieved by a set of bearings guiding the band. Machines are equipped with a limiting switch and ON/OFF switch compliant with IP54. Swivelling saw frame for double bevelling within -45o - + 60o. Technical data Cutting band size 1640×13×0.65 mm Cutting speed 23/34/54 m/min Power 0,55 kW/230V Arm lowering control stepless, through hydraulic cylinder Cutting range -45° - + 60° Dimensions 942×442×548 mm Weight 103 kg Maximum cutting range [mm] Ffjdpfx Ajmrp Tljgdjt Angle 0°.....ø125 mm.....100×150 mm....100×100 mm -45°.....ø90 mm.....90×75 mm.....90×90 mm +45°.....ø90 mm.....90×75 mm.....90×90 mm +60°.....ø55 mm.....55×55 mm.....55×55 mm Default equipment 3rd generation hydraulic cylinder Table for vertical cuts Quick-clamping vice Coolant system Workpiece limiter - bumper Automatic limiting switches Modern thermal engine protection Mobile base with four wheels User manual The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website. The price is a net price. Price does not include shipping costs. For more information, please contact us by phone or e-mail. We invite you to familiarize yourself with the offer on our website.

Condition: new, Year of construction: 2025, Powerful Band Saw equipped with a movable arm that can rotate from -45° to +60°, a portable vice with quick-locking mechanism, a strain gauge for band tension, and a hydraulically adjustable arm with smooth regulation. Additionally, it features an ergonomically designed control panel, ensuring safety and comfort during operation. The maximum cutting width is 490 mm. Key Features of the Band Saw: The band tensioning wheel is equipped with a dial strain gauge that indicates the proper band tension, ensuring optimal results and blade durability. The saw frame is rigid, made of cast iron, and resistant to twisting. High-quality drive wheels are mounted inside, on which the cutting band is mounted. The control panel is ergonomic, with clearly placed buttons such as the main switch, start, stop, cooling, and band speed control buttons (slow/fast). Additionally, the panel features an emergency stop button that complies with the latest EU safety standards. The panel column contains hydraulic actuator controls, enabling precise regulation of the arm's descent speed and turning it on/off. The drive is stable, thanks to high-quality hardened and ground gears. The powerful motor is appropriately matched to the sizes of the materials being cut. The band’s guidance is reliable due to bearings in the guides that can be adjusted according to the width of the material being cut. The saw is equipped with a mechanism for automatic shut-off when the arm is lowered. The vice is solid and securely holds workpieces. A limiter for cutting workpieces is included in the set. The hydraulic actuator is reinforced, allowing precise adjustment of the arm's lowering speed using a potentiometer. The saw arm can rotate from -45° to +60°, with the lifting force adjusted using a spring. An efficient cooling system is built into the base of the saw. Workpieces can be quickly clamped in the vice. The vice can be adjusted on both sides, enabling cutting at different angles. The set includes a coolant tank with a pump. The saw’s solid body is made of cast iron, ensuring stability during cutting. The band saw's arm can be locked. The base is rigid, allowing operation at a height of approximately 95 cm, which is standard with the saw. Additional Advantages of the Band Saw: Other features include band speed regulation (35/70 m/min), quick-lock vice, movable saw arm from -45° to +60° with a scale reading, a fully functional device with an excellent price-to-quality ratio, a solid construction ensuring precise, quiet, and vibration-free operation, infinitely adjustable hydraulic arm lowering, durable carbide roller guides, reinforced worm gear with bronze components, automatic end switch, and a liquid cooling system as standard equipment. Technical Specifications: Working height: 870 mm Fjdpfsv R Tgtjx Agdoft Cutting speed: 35/70 m/min Band saw dimensions: 3770 x 34 x 1.1 mm Band saw width: 34 mm Cooling system pump power: 0.1 kW Total power: 2.8 kW Voltage: 400V Dimensions (width x depth x height): 2200 x 1400 x 1500 mm Weight: 630 kg

Condition: new, Year of construction: 2025, The CORMAK BS 260G band saws, due to being equipped with a hydraulic cylinder, a cooling and an arm swivelling up to 60°, together with blades from renowned German Röntgen company, are used commonly in ironworking where precision, quality and cutting speed are important. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or by any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Machine's arm is made of profiled CAST IRON. Control panel is located by the arm. The drive from the electric motor directed to the cutting band driving wheel is transmitted by a motor with worm drive. The cutting band is tensioned on two cast iron wheels with a manual tightener and guided by adjustable rolling and linear set of carbide guides. A separate flood coolant container with an electropump is inside. The arm lowering speed (the cutting speed) is adjusted with a hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 36 and 72 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Cutting band saw dimensions 2455×27×0.9 mm Band tension mechanical (manual) Band speed 36, 72 m/min Feed speed 0–50 m/min (stepless feed) Arm lowering control Ffjdjvuf S Nspfx Agdjt stepless – hydraulic cylinder Vice base height 900 mm Power supply 3-phase 400V Motor power 1.1 kW Weight 216 kg Warranty 12 months Manual yes CE declaration yes Angle 0º ø230 260×150 225×225 45º ø165 180×130 165×165 60º ø105 100×90 110×110 *Please note that machine is sold without CEE connector by default, since there are many different types of it. If you would like to receive it with the machine, please write it to the seller before making a purchase/during order proceeding.