Used Screw Jacks for sale (6,656)

Year of construction: 2018, condition: used, Screw compressor Manufacturer: Renner Type: RS132D Year of manufacture: 2018 Technical data - Main drive motor: direct drive of the compressor stages via a shaft coupling - Oil filter / thermostat unit: regulates the cooling of the compressor oil and filters it - Oil-injected compressor stage: compressed air generation - Suction regulator: regulates the amount of air drawn in by the compressor - Control cabinet: controls and regulates the compressor system - Suction air filter: filters the air drawn in - Radial fans: generate cooling air for the oil and compressed air coolers - Compressed air outlet: connection point for an external compressed air network - Minimum pressure retaining valve: maintains a minimum system pressure for oil supply, separates network / system pressure - Fine oil separator with oil suction line, sight glasses, and check valve: oil separation via air-oil filter cartridges, return of separated oil from the compressed air - Safety valve: relieves pressure in case of overpressure - Oil filler plug with oil level monitoring: electronic oil level monitoring - Oil drain: drains the oil reservoir - Compressed air / oil combined cooler: cools the compressed air and the compressor oil - Control system: RENNERtronic - Integrated standby heater Compressor - Counterclockwise rotation (without gearbox) / Clockwise rotation (with gearbox) Suction regulator The suction regulator is mounted directly on the screw compressor. It regulates the volume flow of air drawn in by the screw compressor through the suction filter. Operating principle of the suction regulator: The suction regulator has only one main valve. This valve operates as a stepless control valve as well as a tightly closing shut-off valve. In full-load operation, the suction cross-section is fully open with minimal pressure drop. In part-load operation, the suction cross-section is automatically regulated by limiting the stroke and adjusted to the actual air requirement. When the system is stopped, this valve quickly and automatically closes the entire suction cross-section completely. The multiple functions of the regulator are initiated by only one control unit. Minimum pressure retaining valve The minimum pressure valve is located at the compressed air inlet of the air aftercooler. Dksdpfjzu Aibjx Ap Ieu It performs two functions: 1) As a pressure retaining valve, it prevents the pressure from dropping below a minimum overpressure of 4.5 bar when there is no back pressure. This pressure is necessary to ensure the oil supply to the compressor. At the same time, this minimum overpressure is required for good oil separation. 2) As a check valve, it prevents the backflow of compressed air from the compressed air network or the pressure vessel into the compressor system. This allows the separator vessel to be completely relieved when the system is shut down. The valve operates automatically. Adjustment of the minimum pressure valve may only be carried out by personnel authorized by the manufacturer! Suction air filter The suction air filter is installed in the housing and connected to the suction regulator via a ventilation hose. The micro-dry filter with a fineness of 10 μm is used to filter the suction air. The filter can be cleaned several times before it needs to be replaced. Use only original replacement filters! Pressure transmitter The pressure transmitter, used in all systems with electronic control (RENNERtronic / -Plus), is connected to the compressed air outlet (network press

Condition: used, Year of construction: 2002, PROD. KAESER Dkodpfx Aoz Dhlkop Ieu TYPE BSD72 S/N 1001 YEAR 2002 POWER (kW) 37 CAPACITY (m3/min) 6.20 PRESSURE (bar) 11 HOURS (RUNNING/TOTAL) FREQUENCY CONVERTER no BUILT-IN DRYER no HEAT EXCHANGER no COOLED (AIR/WATER) air ON TANK no DOCUMENTS no

Condition: new, PROD. ATLASCOPCO TYPE G11FF S/N ITJ1078585 YEAR 2026 POWER (kW) 11 CAPACITY (m3/min) 1.51 PRESSURE (bar) 9.75 HOURS (RUNNING/TOTAL) 0 INVERTER no BUILT-IN DRYER yes, R513a 0.5kg HEAT EXCHANGER no COOLED BY (AIR/WATER) air WITH TANK yes, 500 L DOCUMENTS yes Dedpfx Ajz Diquep Ieku CONNECTION 1 NEW/USED NEW

Condition: excellent (used), Year of construction: 2009, PROD. KAESER TYPE ASD47 S/N 1150 YEAR 2009 POWER (kW) 25 CAPACITY (m3/min) 1.07-5.27 PRESSURE (bar) 8.5 HOURS (RUNNING/TOTAL) 67466/78928 FREQUENCY CONVERTER yes BUILT-IN DRYER no Dkjdpfoz Dg Haox Ap Iju HEAT EXCHANGER no COOLED BY (AIR/WATER) air ON TANK no DOCUMENTS no CONNECTION 1 1/4 NEW/USED USED

Condition: used, Year of construction: 2006, functionality: fully functional, cooling capacity: 57 kW (77.50 HP), Trane CHHP0L1TKE0N057A refrigeration compressor several units for sale/ ct1968 Dodsubakujpfx Ap Ioku Manufacturer: Trane Type: CHHP0L1TKE0N057A Refrigerant: Freon Refrigerant type: R134A Power: 57kW, 400V, 50Hz, 3 phases Dimensions: 1000x630x570mm Several pieces, for sale from stock

Condition: excellent (used), functionality: fully functional, Year of construction: 2023, operating hours: 200 h, machine/vehicle number: 230608, 4. Main Extruder Type: CWT95-Plus co-rotating twin-screw extruder; L/D 48 Machine Description: *IE5 AC 250 kW motor *Gearbox: Precise balancing principle applied to increase torque level; High safety factor design; Latest steel alloy material for gears, applied with special heat treatment and manufactured to a high level of precision; Imported NSK bearings and sealing rings; Special lubrication system combined with immersion and forced lubrication solutions; Latest generation plate heat exchanger configured for optimal cooling; Input/output rotation speed: 1480/600 rpm; Torque: 2x1990 N.M Oil pump: 1.5 kW With heat exchanger, flow meter, oil pressure gauge *Power Transmission: Compomac safety clutch torque limiter from Italy, with speed sensor *Extrusion Line: Screw diameter: 93 mm, L/D: 48:1; Maximum screw speed: 600 rpm; Screw configuration: modular structure, torque transmission via splines; Screw material: W6Mo5Cr4V2, surface hardness HRC58～64; Barrel configuration: modular structure, each barrel with a length of 4L/D; The inner surface of the linear material is made of α101, surface hardness is HRC62-64; Barrel No.1: Feeder for all possible components, No. 4 and No. 6 with a side feed port and a venting port. No. 8, 9, 11 with a suction port for degassing. The screw profile will be determined based on the requirement. *2 side feeders for lateral feeding *1 set of degassing adapted to the needs Liquid ring pump, 1m3 water tank, gas and vapor recovery system *Electrical Cabinet Enclosure: Rittal Heat Exchanger: Apex Variable Frequency Drives: ABB PLC: Siemens Dkjdpezxxifsfx Ap Iju Components: Schneider Electric *Spare Parts One set of screw and barrel elements and one set of shafts will be delivered with the machine.

Condition: new, functionality: fully functional, XTS56 - 24D Twin Screw Extruder • Water Cooled 130kW AC Motor and Drive. – Low Noise Dkodpfx Asw Snlwep Iju

Condition: new, Screw compressor AGRE Model Sonetteo 7.5+ 10 Compact screw compressor unit including refrigerant dryer and compressed air tank, 270 liters. Belt-driven. Space-saving. Economical. Easy operation thanks to the Infologic² Basic control system. Efficient compression stage. Perfect solution for industrial and craft businesses. Convincing compressed air quality. Refrigerant dryer installed. Dedpfx Aohun Tzep Ijku Detailed features: Compression concept: Oil-lubricated screw compressor Cooling: Air-cooled, efficient cooling system Drive: Efficient IE3 motor, belt drive Control: Fixed speed Control system: Infologic² Basic control unit Refrigerant dryer: Installed, refrigerant R513A Tank: 270 liters, horizontal, painted, 11 bar Motor power: 5.5 kW Pressure: 10 bar Delivery rate: 780 liters/min Including time-controlled condensate drain Dimensions L x W x H = 1500 x 1350 x 600 mm

Condition: new, Year of construction: 2026, functionality: fully functional, overall weight: 400 kg, total length: 1,800 mm, total width: 700 mm, total height: 1,700 mm, power: 15 kW (20.39 HP), operating pressure: 16 bar, pressure (min.): 6 bar, pressure (max.): 16 bar, noise level: 62 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, Highly efficient screw compressor with 15 kW / 16 bar specifically designed for the high demands of laser cutting, providing clean compressed air (also available with 22 kW) complete 4-in-1 unit frequency-controlled servo motor 500-liter pressure tank refrigerant dryer fine filter new machine, delivery time approximately 1 week We would be happy to demonstrate the machine to you at our facility. highly efficient, permanent magnet servo motor frequency-controlled / load-dependent for clean and dry compressed air suitable for laser applications with animated color display single-stage screw unit Dkedpfxoyll Ene Ap Iou air-cooled durable and low-maintenance optional: also available with an additional adsorption dryer Sales are exclusively to commercial customers. Delivery / consultation / sales only in Germany / Austria. technical data (approx.): length: 1.75 m, height: 1.75 m, width: 0.72 m weight: approx. 420 kg pressure: 16 bar flow rate: approx. 1.7 m³/min at 10 bar (1.2 m³/min at 16 bar) noise level: 62 ± 2 dB(A)

Condition: used, Year of construction: 2017, feed pressure / bar liter capacity / l Dodpfxexy S H Tj Ap Ieku Air consumption / m³/h

Year of construction: 2003, condition: refurbished (used), Stock-No. 2086 twin-screw compounding extruder BERSTORFF type ZE 60 A - UT screw size 2 x 64 mm - 32 LD Capacity 800 kg/h depening material specifications Drive from 197 kW up to 350 kW possible , optional by appoinment L/D 34 - 40 LD , by appointment > due to your material formula needs drive up to 230 kW - 350 kw optional against add.price 1x venting port new control board optional - equipment against additional price: screen-pack-changer pelletizing material feeding , loss-in-weight gravimetrci blenders pellet-classifier and more Please inform which equipment you need for a detailled quotation, thank you. Dsdpfec Rukwsx Ap Ieku All ex stock available

Year of construction: 2004, condition: reconditioned (used), Stock-No. 2054 1used, partly overhauled and functionally tested Single-screw extruder AlphaTec A-ES 75.28 Dkodpfjiyya Asx Ap Iou Screw –Ø 75 mm- 28 LD main drive 75 kW- AC Screw speed up to 80 r.p.m. - adjustable 1x venting port with vacuum-pump cylinder barrel heating apporx. 30 kW installed 3x additional temperature controller for down-stream equipment Control board overhauled You´re welcome for inspection visit in our stock Wuppertal-Germany More extruders available

Condition: like new (used), Year of construction: 2021, functionality: fully functional, Equipment: documentation/manual, refrigerant dryer, type plate available, We offer for sale a screw compressor with an integrated condensation dryer, type Aircraft / Fini A-K-Max 7.5-10-270 K (IE3), manufactured in 2021 by Aircraft. It is manufactured and marked according to CE standards (European conformity). The compressor has been used sparingly and regularly serviced, with documented operating history, including Czech operating and maintenance manuals. Technical parameters: Capacity: 1050 l/min, Maximum pressure: 10 bar, Tank size: 270 l, Dimensions: L: 1200, W: 680, H: 1540 mm, Weight: 280 kg, Electric motor power: 7.5 kW, Voltage: 400 V, Sound pressure level Lp 62 dB. The compressor is in very good technical condition and is ready for immediate use. It can be viewed at our warehouse in Přerov. Dkjdezy Spzopfx Ap Iju

Condition: used, Assorted lot of progressing cavity pumps from various manufacturers (Netzsch, Bornemann, Seepex, etc.), mostly in working condition – but some are not. These pumps were removed from service during ongoing operations. Dedeilu Uqepfx Ap Ioku To be sold only as a lot.

Condition: used, Machine: Discharge Screw, Screw Conveyor, TSF 315 Solid Body Screw, second-hand Manufacturer: Askania Mass: 495 kg Year of construction: 1996 Length: 5,20 m Ø auger: 350 mm Weight: 435 kg Dksderl Sv Sspfx Ap Iou Speed: motor 1400 rpm / gearbox 53 rpm Engine power consumption: 2.2 kW Gear oil: 1.8 l Material: Housing > galvanized steel, auger > mild steel / cover > stainless steel

Condition: used, Machine: screw conveyor, screw conveyor, hollow screw conveyor Length: 8.10 m Ø screw: 500 mm Dkedpfjrn T Urox Ap Iou Manufacturer: IEM Fördertechnik Type: Solid body screw conveyor, supported on both sides, without motor

Condition: used, Solid body auger: Steel with bearings on both sides Diameter: 330 mm Dkodpfx Aort T Alop Isu Housing: galvanized steel and painted sheet metal (hopper) Manufacturer: ROEDER Type: TS 315 Year of construction: 1992 Gearbox: SK 22-100 L/4 , 59 1/min max. 302 Nm Length: 3,40 m

Year of construction: 2014, operating hours: 30,000 h, condition: used, functionality: fully functional, machine/vehicle number: 20526471, Laboratory Twin Screw Extruder – Coperion ZSK 26 Mc18 (40 L/D) with a 26 mm screw diameter Featuring all the characteristics of the ZSK Mc18 series, this extruder is ideal for formulation development and compound sampling, as well as for manufacturing small compound batches of up to approximately 180 kg/h. Compared to the previous model ZSK 26 Mc, the new laboratory extruder enables throughput increases of up to 100%, owing to the torque having been increased to 15 Nm/cm³. The extruder is mobile and space-saving as the control cabinet is integrated into the machine’s base frame. Heating and cooling systems are installed and operational (plug & play). Machine No.: 20526471 Year of manufacture: 2012 Operating hours: approx. 30,000 h Dksdpfoyhd Dbsx Ap Iju Condition: Used, in operation Technical specifications: Extruder type: Twin screw extruder Model: ZSK 26 Mc18 Process length: 40 L/D Drive power: 36.9 kW Power supply: 3 × 400 V (−10 % / +6 %), 50 Hz ±2 % Barrel configuration: E-0-0-S-0-0-1-0-V-0 Output: approx. 150–200 kg/h, depending on formulation, raw material, and required product quality Applications: Highly filled compounds, masterbatch applications Suitable for processing: LLDPE, LDPE, HDPE, PP, PPR, PS, ABS, PET, and biopolymers Scope of delivery Gravimetric feeding system: - K-Tron gravimetric feeders - 1 × pellet feeder - 1 × powder feeder (twin screw design) Side feeding / degassing: - 1 × side feeder ZS-B25 - 1 × vacuum side degassing unit ZS-EG25 Vacuum system: Busch vacuum pump Plastex MI 0120 B 222 CNX6, specifically designed for PET applications. Please note: Vacuum pump is not included. Process monitoring: - Melt pressure sensor system - Melt temperature sensor system - PLC integration Pelletizing system (strand pelletizing): - Air dryer unit not included - Strand pelletizer SP50 - Water bath Peripheral equipment: - Bag emptying station for pellets - Conveying system to the feeders Spare parts: - Spare parts included, second screw set.

Condition: used, Year of construction: 2015, operating hours: 3,002 h, load capacity: 1,600 kg, lifting height: 220 mm, fuel type: electric, construction height: 1,250 mm, gearing type: automatic, overall weight: 430 kg, empty load weight: 289 kg, total length: 1,660 mm, color: silver, mileage: 3,002 km, first registration: 08/2015, suspension: other, number of seats: 1, driver cabin: other, wheelbase: 1,304 mm, emission class: none, fuel: electricity, The Still EXU 16 presents itself as a reliable and cost-effective solution for in-house material handling—designed for businesses that value efficiency, precision, and durability in equal measure. With its robust construction and proven electric technology, this device impresses with quiet, emission-free operation, making it ideal for daily use in warehouse and logistics environments. Dsdsymgvwepfx Ap Ioku The automatic controls provide particularly intuitive and comfortable handling, allowing even longer operating periods to be managed effortlessly. Thanks to its compact dimensions and well-thought-out design, the pallet truck can be maneuvered precisely even in confined spaces, while the solid build ensures stability and safety in every situation. With a lift height of 215 mm, it reliably meets the demands of modern local goods handling. The 3,002 operating hours attest to well-maintained use and highlight the vehicle’s readiness for immediate deployment. The initial registration in August 2015 further indicates that this is a mature and durable model which has proven itself in practical use. This electric pallet truck represents an economical investment in smooth processes, reduced operating costs, and sustainable efficiency—a decision that pays off for your business day after day. Sale only to commercial customers (agriculture, freelancers, small or large businesses) or export. Subject to prior sale and errors excepted.

Condition: used, Year of construction: 2015, operating hours: 2,848 h, load capacity: 1,600 kg, lifting height: 220 mm, fuel type: electric, construction height: 1,250 mm, gearing type: automatic, overall weight: 430 kg, empty load weight: 289 kg, total length: 1,660 mm, color: silver, mileage: 2,848 km, first registration: 08/2015, suspension: other, number of seats: 1, driver cabin: other, wheelbase: 1,304 mm, emission class: none, fuel: electricity, The Still EXU 16 stands for efficient material handling, reliable technology, and a thoughtfully designed construction that effortlessly meets the daily demands of warehouse operations. This model impresses with its combination of compact size and a powerful electric drive, ensuring quiet and emission-free operation at all times—ideal for modern working environments with high requirements for efficiency and sustainability. Dodpfeymgv Dex Ap Ioku The automatic drive system provides particularly pleasant and intuitive handling, allowing work processes to be completed quickly, safely, and without unnecessary interruptions. Especially in busy warehouse settings, this pallet truck demonstrates its strengths with precise control and a high degree of maneuverability. With a lift height of 215 mm, it is perfectly suited for fast and reliable pallet transport, helping to significantly accelerate logistics workflows. Thanks to its compact length of 1,660 mm and narrow width of 720 mm, the truck remains extremely agile and flexible even in confined spaces. The 1,304 mm wheelbase ensures stable and safe handling, even during intensive use. The 2,848 operating hours indicate a solid usage record and underline the ongoing high operational readiness of this proven machine. First registered in August 2015, this is a mature model that has proven its worth in everyday practice. This electric pallet truck is therefore a cost-effective investment for companies seeking to optimize their internal processes, reduce operating costs, and rely on long-lasting quality. By choosing the Still EXU 16, you are investing in a dependable piece of equipment that sustainably improves your material flow and delivers consistent performance every day. Sale to businesses only (agriculture, freelancers, small and large enterprises) or for export. Errors and prior sale excepted.

Condition: used, Year of construction: 2011, operating hours: 455 h, load capacity: 1,600 kg, fuel type: electric, gearing type: automatic, overall weight: 500 kg, empty load weight: 276 kg, color: silver, mileage: 455 km, first registration: 03/2011, suspension: other, number of seats: 1, driver cabin: other, emission class: none, fuel: electricity, The Still EXU 16 is a used low-lift truck, ideal for use in warehouses and industrial areas. The vehicle has an electric drive and was first registered in March 2011. With a mileage of 455 km and the same number of operating hours, it still demonstrates good operational readiness. Its chassis features a striking orange color, and the transmission is in automatic mode, ensuring ease of use. Dkedpfx Apswdyuvj Iou With a permissible total weight of 500 kg, the Still EXU 16 is designed to efficiently handle a variety of transport and stacking tasks. The vehicle has one previous owner and is in good used condition. The vehicle can be delivered within Germany for an additional charge, or it can be viewed on-site in Rohrbach (Palatinate). Viewings are possible Monday to Friday from 8:00 a.m. to 5:00 p.m. and Saturday from 9:00 a.m. to 2:00 p.m. A competent team is available by phone or email for further details and inquiries. Sale only to commercial customers (agriculture, freelancers, small and large businesses) or export. Errors and prior sale excepted.

Condition: good (used), Year of construction: 2005, operating hours: 50,000 h, functionality: fully functional, overall weight: 850 kg, Equipment: refrigerant dryer, Screw compressor, 22 kW, with built-in refrigerated dryer; disassembled but in good condition. Dkedpezb Drxjfx Ap Iju

Condition: good (used), Year of construction: 2002, functionality: fully functional, overall weight: 700 kg, The 30 kW screw compressor has been disassembled and is ready for shipment. Djdpfx Apezb Dq Io Ijku

Condition: excellent (used), Year of construction: 2020, S016059 PROD. ALUP TYPE SCK30 CE S/N ITJ370650 YEAR 2020 POWER (kW) 22 CAPACITY (m3/min) 3.22 m3/min PRESSURE (bar) 10 HOURS (RUNNING/TOTAL) 0 (new controller) Djdpfx Apoz A Tm Ds Ieku INVERTER NO BUILT-IN DRYER NO EXCHANGER NO COOLED (AIR/WATER) AIR ON TANK NO DOCUMENTS YES CONNECTION NEW/USED Used

Condition: new, Year of construction: 2012, functionality: fully functional, machine/vehicle number: SB306, Equipment: 3rd hydraulic function, Cold forming machine, 3 dies, 3 blow, Essebi model SB 306, new, 2012, never used + with Schwer+Kopka system. Technical specifications: Wire diameter (500N/mm2): 2-8 mm Cut-off length: 4-80 mm Die ejection length: 4-60 mm Forming power: 40 T Main motor power: 20 kW Max. speed (pieces per minute): 280 Bush cutting: 28 mm Die hole diameter: 50 mm Dkedpfx Asz A Umrsp Isu Punch diameter 1st: 32 mm Punch diameter 2nd: 38 mm Punch diameter 3rd: 42 mm Machine size: 350 x 200 x 200 cm Net weight: 7,000 kg