Used hydraulic presses double column / Four column presses for sale (310)

Condition: as good as new (ex-display), Year of construction: 2020, Hydraulic 400 to column press suitable for continuous shift operation, with these basic data: a) Closing speed 100 - 450 mm/sec. b) Opening speed 50 - 250 mm/sec ( adjustable via touch screen ) c) Pressing speed 5 - 60 mm/sec ( adjustable via touch screen ) d) Piston accumulator with approx. 4 nitrogen bottles e) Table size (clamping surface) 2700 x 1700mm ( seen from the front, between the columns ) f) Total table size 3400 x 1700mm g) 28 T-slots according to customer requirements h) Table, ram and press head are annealed stress-free. i) column diameter 250 mm j) slide size 3400 x 1700mm (clamping surface 2700 x 1700mm ) k) Total size of the machine approx. 3900 x 2200 ( at the bottom ) x 5700 mm height l) Oil temperature monitoring ( adjustable via touch screen ) m) Automatic lubrication ( adjustable via touch screen ) n) Free positioning of the ram ( adjustable via touch screen ) o) KEYENCE light barriers 14 mm on front and rear side p) Circuit oil cooling ( adjustable via touch screen ) q) Pressure holding valve 0 to 600 sec. ( adjustable via touch screen ) r) Table top size 3400 x 1700mm, plane milled s) Laterally monitored doors, 1200mm high, 1000mm wide t) RITTAL control cabinet, 2200 mm wide, up to 20 m from the press u) Pressure setting from 50 to 400 tons ( adjustable via touch screen ) v) Travel limitation optionally via pressure or position w) Programming mode, set-up mode, single stroke + continuous stroke (adjustable via rotary switch ) x) Swivelling control panel with 15 inch touch screen monitor y) Two-hand operation on both sides z) Prepared for automatic material feed ( SIEMENS S 7 1500 ) aa) Machine body primed and painted bb) assembly, commissioning, instruction against separate charge The hydraulics of the presses we offer are completely based on BOSCH-REXROTH/Parker/HAWE components. In the switch cabinet only components are used (SIEMENS) which are easily available in Germany. The safety technology comes completely from SICK except for the light barriers. The control system is supplied by SIEMENS. ( S 7 1500 ) as well as the touch screen monitor with 15 inch. The SIEMENS remote maintenance unit SECOME -Ethernet is included in the scope of delivery. SPECIAL FEATURE: the design chosen by us with two press cylinders and the piston accumulator make it possible to supply the full power with a main motor of 90 kW. Below under 1.3 the technical details Technical data Press design Press design Column press Thermally neutral 80 - 120 °C Number of operating sides 2 sides Forces Pressing force max. 4,000 kN Free ripping force max. 600 kN Pressure build-up time Closed tool steel to steel Max. 2 sec. Dimensions - intended minimum tool height 600 mm Max. Opening width 1600 mm Stroke and min. opening 1000/600 mm Table height above floor 820 mm Height above floor (headroom) approx. 5700 mm Hall height min. 7000 mm Parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.17 mm/m Weight Total weight of the press without operating materials approx. 52 To Speeds ( see attached cycle diagram ) Fast closing 100 - 450 Psdpfx Agjg Iihwezoha mm/s Pressing speed At F max.

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. Psdpfsg Rn Efex Agzoha All statements without guarantee. Without transport costs.

Condition: used, Year of construction: 1952, Type of machine: Psdpfxjwxw H Es Agzoha Down-stroking press Manufacturer: SACK&KIESSELBACH Model: EP500 Year of construction: 1952 Pressing force: 500 t Clear gap: 450 mm Location: In Germany

Condition: excellent (used), Year of construction: 2004, Manufacturer: MULLER WEINGARDEN Model: G2-1400/630 Year: 2005 Condition: Used Stock Number: 0362 CONDITION: EXCELLENT Press Force: 1,400 t Slide Stroke: 1,500 mm Slide Working Speed: 40 to 127 mm/s Approach Speed: 700/850 mm/s Table Dimensions: 3,500 x 2,500 mm Pedpjw Hdpcofx Agzsha Front Opening: 3,500 mm Lower Blank Holder Cushion Force: 400 t Lower Blank Holder Cushion Stroke: 300 mm Side Opening: 2,400 mm Lateral Movable Table: Present (side) Press Force (Secondary): 630 t Press Slide Stroke: 1,300 mm Press Table Size: 3,350 x 2,130 mm Front Opening (Press): 3,350 mm Press Slide Working Speed: 12 to 20 strokes per minute Side Opening (Press): Lateral opening present

Condition: used, Year of construction: 1970, pressure 1000 t distance between columns 5000 mm stroke 500 mm Height of centres 400 mm Overall size 6000 x 2500 mm Weight 1000 kg Phjdpfx Agewwl R Aszea Distance between centres 3500 mm weight of the machine ca. 220 t

Condition: reconditioned (used), Year of construction: 1985, functionality: fully functional, press power: max. 630 to. daylight: max. 375 mm stroke: max. 275 mm Phodpfx Agegwv S Ujzoa weight: 4.500 Kg.

Condition: like new (used), Year of construction: 2019, pressure:400 t Phjdpfxofh Izme Agzea stroke:900 mm Table dimensions:1200 x 1200 mm Deep-Drawing Pillow:150 t travel away deep-drawing pillow:280 mm Daylight Opening:1100 mm

Condition: used, Year of construction: 1991, pressure 400 t stroke 300 mm table surface area 1200 x 700 mm ram surface 1200 x 700 mm dayligth 500 mm adjustment of stroke 300 mm return capacity 348 kN capacity of ejector 100 kN Phjdpjtqqlcjfx Agzja ejector stroke 100 mm control SIEMENS Simatic S 5 total power requirement 65 kW weight of the machine ca. 28 t dimensions of machine L x W x H 4,4 x 2,75 x 4,0 m = Frame press Accessories: tool changing table - with cutting shock absorption damping force 4000 kN damping stroke 5 mm spindle adjustment 200 m

Condition: good (used), Year of construction: 1971, pressing force: 630 t, Manufacturer: Sack & Kiesselbach Model: EP 630 Mode of operation: oil-hydraulic Table height: 1175 mm Pedpfxowxw Amo Agzoha Stroke: 305 mm Tool installation height: 317 mm Rapid approach descending speed: 6.9 mm/s Pressing speed: 0.3 mm/s Return speed: 6.3 mm/s Drive power: 11 kW Electrics: 550 V / 60 Hz Information without guarantee.

Condition: used, Year of construction: 1984, pressure 500 t passage width 750 mm stroke 120 mm total power requirement 57 kW Phjdpfx Ast Hwpyegzoa weight of the machine ca. 16 t dimensions of the machine ca. m

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-250E/NC, pressing force: 250 t, table width: 2,500 mm, table length: 1,150 mm, Equipment: documentation/manual, safety light barrier, HYDRAULIC FOUR-COLUMN PRESS FOR DEEP DRAWING APPLICATIONS TECHNICAL DATA Press force / Main cylinder 250 t Blankholder force 50 t Motor power 11 kW Ram stroke 500 mm Approach speed 80 mm/s Working speed 7 mm/s Return speed 105 mm/s Column diameter 150 mm Maximum pressure 260 bar Usable table area 2,500 x 1,150 mm Column clearance 2,500 x 700 mm Maximum open height 1,000 mm Blankholder (cushion) size 950 x 750 mm Working height 1,100 mm Overall height 3,650 mm Weight 15,000 kg The hydraulic four-column press MV-250E/NC belongs to the M/NC series and is specially designed for high precision and capacity, particularly in deep drawing operations. Outfitted with upper and lower tables made from C45E steel, featuring DIN-650 T-slots to ensure minimal friction during vertical movement of the upper table. This is facilitated by maintenance-free bi-metal bushings and perfect parallelism by means of four chrome-plated and precision-ground cylindrical columns. The press features an optimized hydraulic system operating at pressures below 290 bar, ensuring long service life and reliable performance. It complies with all essential safety and health requirements in accordance with CE regulations. STRUCTURE AND TABLES • Consists of three fully welded blocks, manufactured exclusively from S355JR steel. Podpfxjwkuchj Agzsha • Stabilized and machined after welding to ensure perfect parallelism and precision. • Designed and calculated using finite element analysis software. • The lower table is equipped with a 50-ton hydraulic cushion, usable area 950 x 750 mm, and three front supports for tooling outside the press. • Integrated SIEMENS KTP-400 NC for controlling ram stroke, speed changes, and cushion control. • Includes a SIEMENS S7 PLC, permitting storage and programming of up to 99 settings. CYLINDER AND HYDRAULIC UNIT • Single-acting cylinder with honed sleeve, chrome-plated piston, and wear-resistant guides. • Complete hydraulic unit installed on the top of the press. • Hydraulic unit comprises a low-noise Denison hydraulic pump and an air-oil cooler. • Includes: - Decompression system - Solenoid operated pressure valves - Pre-fill valves - Communication valve - Check valve - Pressure relief valve - Safety catch valve ELECTRICAL INSTALLATION AND SAFETY • Features a SIEMENS SIMATIC S7 1200 safety PLC and a 4-inch KTP-400 touchscreen on the control panel. Enables programming of semi-automatic and automatic modes, power, stroke, and dwell time. Offers storage for up to 99 recipes; each recipe is fully programmable for the above parameters. • The electrical control panel features a selector switch for mode selection: manual “setup” or automatic “production” cycle. • Machine operation via electric low-voltage foot pedals. • Safety features include category IV light curtains in the front working area, two fixed side guards, and a rear safety guard with a magnetic interlock detector.

Condition: good (used), Year of construction: 1970, pressure 80 t passage width 350 mm stroke 600 mm table dimension - longitudinal 400 mm dimensions of the machine ca. 1400 x 1050 x 2350 m Phedevwgqrspfx Agzea

Condition: used, Year of construction: 2021, functionality: fully functional, pressing force: 500 t, Hydraulic 500 T Gantry Straightening Press with tool clamping device and parallel support for the bending blade a) Idle and pressing speed up to 17 mm/sec b) Opening speed up to 44 mm/sec c) Table size 2000 x 850 mm Phedpfowgakvex Agzoa d) Open height 1500 mm e) Overall size approx. LWH 1500 x 3000 x 4300 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) Table with grid design i) Remote control j) Pressure adjustment from 80 T to 500 T via rotary dial k) Table moves hydraulically outward 700 mm for loading l) Cylinder moves left and right via racks m) Machine body powder-coated or double-coated n) T-slots according to customer requirements o) Cylinder induction-hardened p) Assembly, commissioning, and instruction are charged separately. Press type: GANTRY PRESS Thermally neutral 80 – 120 °C Number of operating sides: 3 Forces Max. press force: 5,000 kN Max. free tear-off force: 800 kN Pressure build-up time: Closed tool, steel on steel: Max. 3 seconds Dimensions Max. opening width: 1,500 mm Stroke and min. opening: 1,300 mm/200 mm Table height above floor: approx. 850 mm Height above floor (overhead height): approx. 4,300 mm Hall height: min. 5,000 mm Deflection Determined at max. closing force with 70% occupancy: < = 1.2 mm/m Weight Total weight of the press without operating materials and table top: approx. 25 t Speeds Quick closing with 17 mm sec. Pressing speed at F max.

Condition: used, Year of construction: 1982, pressure 40 t distance between columns 695 bzw. 215 mm stroke 100 mm table surface area 650 x 440 mm ram surface 580 x 285 mm dayligth 400 mm total power requirement 15 kW weight of the machine ca. t dimensions of machine L x W x H 1,63 x 1,05 x 2,61 m - with die cushion - with light bareer make SICK Phsdpotqqq Rsfx Agzea

Condition: excellent (used), Year of construction: 2015, With a view to optimized and energy-saving drives in the vehicle industry, significantly higher demands are placed on the components of the drive system. Higher power transmission and higher torques combined with smaller size are the challenges. This development has increased the demand for cold-formed splines. With the Vertical Splines Press (VSP) Sack & Kiesselbach provides the customer with a solution that offers technological and also logistical advantages compared to conventional technologies (such as roller burnishing or broaching). The relatively small and very user-friendly press can be configured both manually and as an automated system. In addition to the splines press, the customer can also obtain the appropriate die system and process technology from a single source. 1 used Vertical Splines Press make Sack & Kiesselbach type VSP 50/30 Year 2015 Technical data: Pressing force 500KN Phedpfx Aogtty Tsgzja ram stroke 450 mm Closing speed 200 mm/s pressing speed 5,5 mm/s opening speed 120 mm/s table dimension 500 x 400 mm installation height 1000mm width between columns 530 mm splines cylinder speed 3-9,5 mm/s Dimensions height 2900 mm width 3100 mm depth 1400 mm Drive power 8 KW Special equipment Digital measuring system Splines tool for internal splines

Condition: used, Year of construction: 1987, pressure 125 t distance between columns 1050 mm Phedpfxjt Hwuio Agzea stroke 250 mm total power requirement 40 kW weight of the machine ca. 8,5 t dimensions of the machine ca. m

Condition: used, Year of construction: 2021, functionality: fully functional, total height: 7,000 mm, total width: 4,750 mm, total length: 6,000 mm, pressing force: 1,000 t, reverse speed: 60 mm/s, The MV-1000E/NC-SINCRO hydraulic press is custom-designed for the adjustment of progressive dies. It features a tilting upper table and a movable lower table made of C45E steel, machined with DIN-650 T-slots to ensure minimal friction in the vertical movement of the upper table. This is achieved through the installation of maintenance-free bimetallic bushings and perfect parallelism ensured by four high-mechanical-resistance cylindrical columns of 300 mm in diameter, chrome-plated and rectified. STRUCTURE AND TABLES • Features a structure made from oxy-cut steel divided into three electro-welded monoblocks, exclusively manufactured from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed with finite element software. • Cylindrical columns with a diameter of 300 mm, high mechanical resistance, rectified, and chrome-plated to maintain a low friction and wear coefficient. • Upper table with T-slots and anti-fall safety system. • Useful table surface: 4,750 x 2,250 mm. • Structure designed to support 600 TN of concentrated force on 1/3 of its surface. • Lower table designed to support up to 50 TN in displacement, supported by bronze guides with graphite load and mechanical positioning centers for precise table positioning. CYLINDER AND HYDRAULIC GROUP • 6 single-acting cylinders with lapped sleeves, chrome-plated pistons, and anti-wear guides. • Four 50 TN hydraulic compensators located at the ends of the lower table. • 800-liter hydraulic group with a silent Denison pump, automatic disconnection of the fast approach pre-filling speed, and equipped with a decompression system in working speed. Phjdpfjwpgwnox Agzsa • Proportional pressure system and optical gauges for displacement control on the upper table, with a synchro-electronic system for compensating off-center or unbalanced forces. • Hydraulic group cooling system with an independent air-oil radiator unit. • All M series hydraulic presses include a lateral pressure switch to adjust the most suitable pressure setting for each type of work. • Glycerin manometer with tonnage reading. ELECTRICAL INSTALLATION AND SAFETY • Includes a SIEMENS safety PLC model SIMATIC S7 1200 and a 12” touchscreen. Allows programming of semi-automatic and automatic operating modes, power, travel, and upper table dwell time. Capable of storing 300 recipes, with each recipe able to program all the above values. • Low voltage operation via two-hand pushbutton. • Anti-fall safety system with hydraulic safety jaws. • Level IV photoelectric barriers installed at the front and rear. • Lateral protections with opening and safety microswitches. TECHNICAL SPECIFICATIONS Power tn 125 - 1000 Opening Force tn 100 Powered Speeds 1 Engine Power kW 75 Fast Pre-Fill Speed mm/s 100 Variable Working Speed mm/s 12-4 Return Speed mm/s 60 Guide Diameter mm 300 Maximum Pressure Bar 290 Useful Table Area mm 4.750 x 2.200 Lower Table Displacement mm 2.200 Vertical Travel of Upper Table mm 800 Between Columns mm 5.000 x 1.490 Total Front mm 6.000 Total Side mm 4.750 Total Height mm 7.000 Weight kg 150.000

Condition: good (used), 1 used single-sided press Make: SACK & KIESSELBACH, Psdpfsul U Svex Agzsha year of construction: 1962,74 serial number 31900 Pressing force 630 t, stroke 310 mm Installation height 320 mm Working height 1200 mm Drive power 10 KW

Condition: used, Year of construction: 1985, pressure 63 t passage width 1350 mm stroke 300 mm Phsdpfxet Hwxuo Agzja total power requirement 16 kW weight of the machine ca. 10 t dimensions of the machine ca. 2,0 x 1,8 x 3,4 m

Condition: used, Year of construction: 2020, functionality: unexamined, total height: 6,400 mm, total width: 4,500 mm, total length: 3,800 mm, operating speed: 110 mm/s, reverse speed: 180 mm/s, distance table to ram: 1,500 mm, We are offering here a new build of the machine shown. The machine was put into operation in 2020 and can be inspected by the customer. Technical data: Press force T 800 Opening force T 80 Motor power KW 55/75 + 55/75 Piston stroke 1000mm Rapid pre-fill speed mm/s 110 Working speed mm/s 6 Return speed mm/s 180 Guide diameter mm 250 Max pressure Bar 250 Useful table area mm 3,500 x 2,000 Lower table displacement mm 2000 Between columns mm 2,000 Open height mm 1500 Total front mm 3800 Total side mm 4500 Total height mm 6400 Weight kg 134,600 The MV-800E/NC-SINCRO press was specially developed for the adjustment and testing of molds, dies, and stamps. The 4 columns with 250 mm diameter made of C45E steel were specially manufactured for high stress. It features an optimized hydraulic system with a pressure of up to 250 bar, ensuring long service life and reliability. It meets all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLE • A structure that withstands 600 T concentrated force on 1/3 of its surface. • Lower table with T-slots. • Upper table with T-slots. • Usable table surface: 3,000 x 2,000 mm. CYLINDER AND HYDRAULIC UNIT • Two double-acting hydraulic cylinders with 400 T each. • Single-stage hydraulic unit with automatic shutoff of pre-fill speed and independent operation, equipped with a decompression system and proportional pressure pre-fill valves. Equipped with digital potentiometers on the upper table for displacement control and an electronic synchronization system to compensate for off-center or unbalanced forces. • The press is equipped with a side pressure switch to regulate the most suitable pressure setting for each specific task. • Glycerin manometer with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Electrical installation for operation with 1 or 2 speeds of the main cylinder feed. • The press has a manual cycle and an automatic cycle (activated via a test button selector): • The manual cycle allows the execution of all movements (step by step) of the press at slow speed. • The automatic cycle allows the press to perform a complete production cycle. • Electrical safety system for the upper table fall protection system. Phedpswlrv Uofx Agzoa • Lower table with hydraulic removal and physical stops. • The machine features a control panel with a touchscreen display for entering operating and calibration data. • 2 optical barriers of 1,000 mm with safety level IV installed at the front and rear. • Electrical components from Siemens are manufactured according to applicable CE regulations and laws in protection class IP55. • Electrical and hydraulic functions are redundant and self-controlled. Includes an additional safety block and self-monitoring devices for operation and safety. Includes inspection and certification of correct operation and safety distance for light barriers. • Safety is ensured by a laser and area protection with light barriers of level IV.

Condition: like new (used), functionality: fully functional, machine/vehicle number: FDL-150-100E/NC, total length: 1,200 mm, pressing force: 150 t, table width: 800 mm, working height: 600 mm, clearance between the columns: 1,250 mm, Equipment: documentation/manual, safety light barrier, DOUBLE-COLUMN HYDRAULIC PRESS WITH TWO SIDE CYLINDERS FOR PRE-PRESSING AND PRESSING OF ROTORS AND STATORS, AND A CENTRAL CYLINDER FOR ROTOR SHAFT EXTRACTION, AS WELL AS FOR SHAFT EXTRACTION IN CASE OF REPAIR It features an extendable table for stacking and handling rtors and stators. It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of a rigid fixed bench welded structure made exclusively from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Mechanically movable grooved table measuring 1200 x 800 mm with a stroke of 1,200 mm, equipped with a worm gear reducer and a 0.5 HP electric motor with brake. • Central drill on the table with a diameter of 250 mm and a maximum depth of 550 mm. • Useful lifting capacity of the table for moving 4 tons. • Movement speed of 30 mm/sec. • Front interior width of 1250 mm (space between columns). • Working height of 600 mm. MAIN CYLINDERS: 150 TN • Two 75-ton hydraulic cylinders (150 tons total), with a stroke of 1200 mm connected by a plate with a central hole of 250 mm in diameter. • Maximum useful height of the cylinder plate: 1,440 mm. • Minimum useful height of the cylinder plate: 200 mm. ABSTRACTION CYLINDER • One 100-ton central cylinder with a stroke of 1200 mm. • Designed to accommodate an abstraction clamp, end of the rod threaded to M 35.150 x 40 mm length. • Maximum useful height of the abstraction cylinder: 1600 mm from the root of the rod thread. • Minimum useful height of the abstraction cylinder: 400 mm from the root of the rod thread. HYDRAULIC GROUP • Two-speed hydraulic group with 5.5 HP power “Siemens Motor”, with automatic disconnection of high speed and independent speeds. Maximum pressure: 250 bar. • Pressure regulation system using proportional valves. • Air-oil cooler. • Temperature sensor. • Hydraulic group located on the right side. ELECTRICAL INSTALLATION AND SAFETY • Equipped with a SIEMENS mod. SIMATIC S7 1200 safety PLC and a 12” HMI touchscreen mod. MTP with 99 memory slots allowing adjustment of pre-pressing power, pressing, calendering, and stroke of the pressing and extraction cylinders, as well as the holding times during processes. • Electrical and hydraulic maneuvers are redundant and self-controlled. They include an additional safety block and self-control devices for operation and safety. Includes verification and certification of correct operation and safety distance for photoelectric cells. • The electrical panel includes a selector for choosing the type of work in manual, semi-automatic, or automatic position and a selector for high-speed or low-speed operation. Phodpjwpg Awofx Agzja • Operation is performed via a two-hand low-voltage electrical pushbutton. • All installed electrical materials are Siemens, including relays, contactors, main motor, etc. • Ready for Industry 4.0. • To ensure safety, it includes category IV photoelectric barriers located in the front work area, two fixed side guards, and a practicable rear guard with a magnetic disconnection detector.

Condition: used, Year of construction: 2024, functionality: fully functional, total height: 2,675 mm, table height: 900 mm, total width: 1,075 mm, total length: 1,525 mm, pressing force: 100 t, table width: 700 mm, table length: 500 mm, overall weight: 2,540 kg, reverse speed: 60 mm/s, distance between side stands: 800 mm, stroke length: 250 mm, Equipment: safety light barrier, RIGID FRAME HYDRAULIC PRESSES We have engineered the motorized rigid frame hydraulic presses of the R/NC series in six different capacities ranging from 80 to 500 tons. Specially designed for stamping, die-cutting, and drawing operations. The latest generation R series hydraulic presses have evolved into highly versatile machines, including the capability to integrate seamlessly into automatic production lines. They operate at a hydraulic pressure below 320 BAR to ensure maximum durability of the entire hydraulic system. The R/NC series drawing and stamping presses feature an electro-welded frame made exclusively from S355JR steel, stabilized and precision-machined after welding for perfect parallelism and accuracy. The frame design and strength are optimized using finite element analysis software, ensuring our high standards of precision and quality are always maintained. Both the upper and lower tables are made from precision-machined C45E steel and feature DIN-650 T-slots. The upper table maintains perfect parallelism by means of four lateral cylindrical guides with maintenance-free, anti-friction bimetallic bushings. The double-acting cylinder features a lapped barrel, a chrome-plated piston, and maintenance-free wear guides. The hydraulic unit is motorized, offering two speeds with automatic disengagement of the rapid speed, and includes a cylinder decompression valve. Standard features include a SIEMENS SIMATIC S7 1200 safety PLC and a 4” MTP-400 touchscreen positioned above the electric foot pedal control. This setup allows for programming of semi-automatic and automatic operating modes, power, stroke, and dwell time of the upper cylinder. Up to 99 recipes can be stored, with full parameter settings for each recipe. The electrical control panel includes a selector switch for manual/automatic operation, and a key switch for maintenance tasks. All electric and hydraulic controls are redundant and self-monitored, with an additional safety block and safety self-monitoring features. The machine includes verification and certification of correct operation, as well as the safety distance of the light curtains. Safety features include type 4 PLe photoelectric light curtains at the front working area, two fixed side guards, and a rear access guard equipped with a magnetic disconnect sensor, polycarbonate windows, and LED interior lighting. Installation of a hydraulic cushion or ejector is supported. Compliant with all essential CE safety and health requirements. Supplied with an instruction manual. Phsdpfxewlgkme Agzja Technical Specifications: - Force: 100 t - Motor power: 13 kW - Working speed: 3–9 mm/s - Approach speed: 40 mm/s - Return speed: 60 mm/s - Maximum pressure: 319 bar (up to 320 bar) - Ram stroke: 250 mm - Guide diameter: 50 mm - Lower table: 700×500 mm - Upper table: 600×450 mm - Max. vertical opening: 500 mm - Front opening: 800 mm - Working height: 900 mm - Overall front width: 1,525 mm - Overall length: 1,075 mm - Overall height: 2,675 mm - Weight: 2,540 kg

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-600E/NC, pressing force: 600 t, table width: 990 mm, table length: 890 mm, operating speed: 5 mm/s, overall weight: 23,000 kg, reverse speed: 18 mm/s, Equipment: documentation/manual, safety light barrier, The MV-600E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for stamping, deep drawing, punching, and deburring tasks. Power tn 600 Motor Power 40 HP a 440 Vca / 60hz Working Speed mm/s 5 Approach Speed mm/s 15 Return Speed mm/s 18 Piston Stroke mm 1.015 mm - (40”) Guide Diameter mm 200 Table Usable Area mm 990 x 890 x 130 (39” x 35” x 5”) Between Columns mm 990 x 370 Vertical Clearance mm 1.625 - (64”) Working Height mm 990 - (39”) Lower Hydraulic Knockout Tn 80 Lower Knockout Stroke mm 406.4 - (16”) Upper Hydraulic Knockout Tn 80 Upper Knockout Stroke mm 406.4 - (16”) Total Frontal mm 1.850 Total Lateral mm 1.700 Total Height mm 4.500 Weight Kg. 23.000 Kg. approx. Equipped with a top and bottom table made of C45E steel, machined with DIN-650 slots, and a removable upper counter-table of 990 x 890 x 130 mm for die holders with “T” slots. We ensure minimal friction in the vertical movement of the top table through the installation of maintenance-free bimetallic bushings, with perfect parallelism achieved by four chromed and ground cylindrical columns. It uses an optimized hydraulic system with a pressure of 320 Bar, ensuring prolonged durability and reliability in its performance. Podewpggiepfx Agzsha It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of three electrowelded blocks made exclusively of S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Incorporates a SIEMENS SIMATIC S7 1200 PLC and a 7” HMI KTP-700 touch panel. This allows programming of the power, cylinder stroke, and speeds, with a storage capacity of 300 memories for different work cycles. CYLINDER AND HYDRAULIC GROUP • Double-acting cylinder with lapped sleeve, chromed piston, and maintenance-free anti-wear guides. • Motorized hydraulic group with two speeds and automatic disconnection of fast speed. High-pressure pump and 10-micron return filter. Includes cylinder decompression valve, directional valve, and safety valve. A pressure switch located on the side allows the most appropriate pressure setting for each type of work. • Glycerin manometer with reading in tons. ELECTRICAL INSTALLATION AND SAFETY • The electrical panel incorporates a selector to choose manual, semi-automatic, or automatic operation modes, and another selector for fast or slow speed operation. • Equipped with a PLC to internally assist with maneuvers and decompression time. • Operation is carried out using a low-voltage electric two-hand button panel. • Electrical and hydraulic maneuvers are redundant and self-controlled, incorporating an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of proper operation and safety distance for photocells. • For safety, category IV photoelectric barriers are incorporated in the front work area, two fixed side protections, and a movable protection with a magnetic disconnection detector at the rear. • Machine equipped with an IXON system for online communication in case of faults or reprogramming. • Ladder with upper walkway for repair access (scaffold).

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-300E/NC, total height: 3,500 mm, total width: 1,800 mm, total length: 2,300 mm, pressing force: 300 t, table width: 1,250 mm, table length: 1,250 mm, overall weight: 18,000 kg, pressure: 320 bar, Equipment: documentation/manual, safety light barrier, The MV-300E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for deep drawing, punching, and deburring tasks. Power tn 300 Motor Power kW 18 Piston Stroke mm 750 Approach Speed mm/s 110 Variable Working Speed mm/s 5-15 Return Speed mm/s 130 Guide Diameter mm 150 Maximum Pressure Bar 320 Table Usable Area mm 1.250 x 1.250 Between Columns mm 1.250 x 940 Vertical Clearance mm 1.000 Total Frontal mm 2.300 Total Lateral mm 1.800 Total Height mm 3.500 Weight kg 18.000 STRUCTURE AND TABLES Consists of three electrowelded blocks made exclusively of S355JR steel. Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. Calculated and designed using finite element software. The bottom table has a 50 Tn hydraulic cushion with a useful surface of 950 x 750 mm and three front consoles to support the die outside the press.Incorporates a SIEMENS KP-700 COMFORT NC for the regulation of the top table stroke, speed changes, and cushion regulation. CYLINDER AND HYDRAULIC GROUP 2 single-acting cylinders with lapped sleeves, chromed pistons, and maintenance-free anti-wear guides. 2 auxiliary double-acting cylinders for fast approach and return speeds. Variable speed motorized hydraulic group. Includes cylinder decompression valve. Silent hydraulic pump. All hydraulic presses of the M series include a pressure switch located on the side, allowing the most suitable pressure setting for each type of work to be regulated. Glycerin manometer with reading in tons. ELECTRICAL INSTALLATION AND SAFETY Incorporates a Siemens SIMATIC S7 1200 safety PLC and a 7” KTP-700 COMFORT touch screen located on the electrical panel. Allows programming of semi-automatic and automatic modes, power, stroke, and dwell time of the top cylinder and cushion. It has a storage capacity of 300 recipes, each recipe can program all the above values. Prepared for Industry 4.0. The electrical panel includes a selector that allows choosing the type of work to be performed in manual, semi-automatic, or automatic mode and a selector to choose operation in fast or slow speed. Electrical and hydraulic maneuvers are redundant and self-controlled. They incorporate an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of correct operation and safety distance for photocells. Pjdpewphhnsfx Agzeha Operation is carried out by low voltage electric pedal. For safety, they incorporate category IV photoelectric barriers located in the front working area, two fixed side guards, and a practicable guard with a magnetic disconnection detector located at the rear.

Condition: used, functionality: fully functional, pressing force: 150 t, pressure: 250 bar, Double-column hydraulic press equipped with two side cylinders connected by a platen for the pre-pressing and pressing of rotors and stators, and a central cylinder for the extraction of the mandrel and fitting of the rotor shaft, as well as shaft removal during repair operations. Features a retractable table for stacking and handling rotors and stators. MAIN CYLINDERS 150 t - 2 hydraulic cylinders of 75 t each, with a stroke of 750 mm, joined by a slotted platen with a central bore of 250 mm diameter. - Maximum usable height between cylinder platens: 1,300 mm. - Minimum usable height between cylinder platens: 550 mm. EXTRACTION CYLINDER - 1 central cylinder of 80 t, with a 1,200 mm stroke. - Prepared to fit an extraction clamp; rod end threaded M 35 x 1.50 pitch, 40 mm length. - Maximum usable height of extraction cylinder: 1,300 mm to the root of the rod thread. - Minimum usable height of extraction cylinder: 100 mm to the root of the rod thread. TABLE AND STRUCTURE - Mechanically movable slotted table, 1,200 x 800 mm, with a 600 mm stroke, fitted with a worm gear reducer and 0.5 HP electric motor with brake. - Central bore on the table: 250 mm diameter; max. depth 550 mm. - Effective lifting capacity of the table for movement: 4 t. - Table traverse speed: 2,600 mm/min. - Internal front width: 1,250 mm. - Working height: 600 mm. HYDRAULIC POWER UNIT - Two-speed hydraulic unit, 5.5 HP, with automatic disengagement of rapid speed and independent speeds. Maximum pressure: 250 bar. - Digital control for maximum force during pre-pressing, pressing, and fitting; digital tonnage display. Pressure adjustment system via proportional valves. Podpfxjxc Ekdj Agzjha - Selector for approach and measuring speeds.