Condition: new, Year of construction: 2025, functionality: fully functional, total length: 3,636 mm, total width: 2,300 mm, workpiece weight (max.): 200 kg, power: 2.2 kW (2.99 HP), temperature: 220 °C, heating capacity: 39 kW (53.03 HP), inner dimension length: 3,225 mm, inner dimension width: 1,400 mm, inner dimension height: 2,000 mm, workpiece height (max.): 1,600 mm, workpiece length (max.): 3,000 mm, volume flow: 4.5 m³/h, fuel: electricity, insulation material: Steinwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 1,200 mm, Powder coating booth open spray booth Dimensions of the powder booth Width 2,000 mm Depth 2,100 mm Height 2,200 mm Fan 1 fan 6000 m³/h Power 3 kW (electric motor) Filter 4 pcs. type filter cartridges (à ⌀325 x 600 [mm]) Electromagnetic valves 2 pcs. 1" "Turbo" Italy Absolute filter 1 pcs. pocket filter type Wagner "Prima Sprint" powder gun Mains standard 230 VAC Frequency 50 - 60 Hz Inlet compressed air 6-8 bar Outlet compressed air 0.05 - 5.5 Nm³/hour Powder combustion furnace Internal dimensions length 3,225 mm Internal width 1,400 mm Cjdpfjb Dxnwox Ah Uori Internal height 2,000 mm Insulation Rock wool 150 mm [75 kg/m³] Temperature Max. 220°C Fans 1 unit 4,500 m³/h Electric motors 1 pc. 1.5 kW, 1450 rpm, 3 F, 50 Hz Thermal output 39 kW Doors on both sides 2 manual, insulated with rock wool 150mm 70Kg/m³ Indirect heating via thermoblock, Heating chamber Tubular heat exchanger Burner* 1 electric heater Steel support for fastening conveyor technology IPE 80 *Choice of gas, oil or hybrid for an extra charge Manual conveyor technology Substructure Steel profiles IPE and SQ Bends 9040C 90 degrees, radius 600 mm 4 pcs. Rail system no. 9040 27m Roller units 9842 GLRHT 16 pcs. Connectors 9041 M 12 pcs. Fixing clamps 9047/100 16 pcs. Manual tongue switch 45 degrees 9401 AIYM 2 pcs. Load carrier L = 1000 mm 8 pcs.

Year of construction: 2019, condition: used, The EFD machine we are offering has a capacity of 2000 mm, but once the MF and HF adaptation boxes are installed, this travel is limited to approximately 1700 mm. It is equipped with a Siemens 840 D CNC (replaced 3 months ago), with 3 digitized axes: Z, Y (200 mm), and C, a double spindle with dual tailstock controlled separately, 1 MF adaptation box, and 1 HF adaptation box. The machine height is 4400 mm. The maximum workpiece weight on the main spindle is 600 kg. The maximum weight per piece on the double spindle is 50 kg. The converter is transistor-type, with a power output of 300 kW and equipped with three frequency ranges: 100 kHz at 200 kW, 3 kHz and 10 kHz at 300 kW. Parameter monitoring is integrated into the Siemens 840 D CNC. It will control: voltage, current, power, MF or HF frequency, quench flow rate by analog flowmeter, quench water temperature via PT 100 probe, with a color printer included. Optionally, a serial link is available, allowing program transfer to avoid dual programming for the CNC and the RTM 100. SUPPLIED EQUIPMENT: - 1 galvanic isolation mains transformer, 400 V three-phase + earth (for network disturbance protection and operator safety) - 1 SINAC P M/H transistor converter Power: 20 to 300 kW Frequency: 3 to 100 kHz - 1 medium frequency adaptation box with 55 VT 8 transformer Crjdpfjxc Exhjx Ah Uoi 1 capacitor bank for 3 kHz 1 capacitor bank for 10 kHz - 1 high frequency adaptation box without transformer 1 capacitor bank for 100 kHz - 1 manual selector switch for 3 and 10 kHz selection - 1 manual selector switch for 100 kHz or 3/10 kHz selection - 1 standard vertical traversing hardening machine, type HGL 2000, 3-AXIS, equipped with: - 1 SIEMENS 840 D controller (replaced 3 months ago) - 1 X-axis, vertical travel approx. 1500 mm depending on MF and HF adaptation boxes - 1 Y-axis, horizontal travel 200 mm - 1 C-axis spindle rotation, max workpiece weight 600 kg, max diameter 500 mm (according to inductor) - 1 double spindle with dual tailstock - 1 hydraulic circuit with analog flowmeter for quench water - 1 second hydraulic quench water circuit without flowmeter, solenoid valve controlled by program, no flowmeter supplied - 1 simple interface for high frequency inductor connection - 1 simple interface for medium frequency inductor connection - 1 operator access door - Integrated RTM 100 standard process monitoring system in the Siemens 840 D, with color printer - All necessary electrical interconnections for medium, high frequency, and low voltage - Complete documentation in French (user and operating manuals) This installation is highly versatile due to its wide frequency range (low, medium, and high), all provided by a single generator, making it rare on the market. The high power rating of 300 kW enables the processing of large or two workpieces simultaneously.

Condition: excellent (used), Year of construction: 2018, Automatic Galvanizing Barrel Plating Line GALWANOTECHNIKA (2018/2021) Technical Data Summary (Focus on Components and Capacity): ● Machine Type: Automatic Galvanizing Line, Barrel Type (Zn - Zinc Plating). ● Manufacturer: GALWANOTECHNIKA. ● Year of Manufacture: Main structure 2018, significant modernization 2021 (documented). ● Capacity: Approx. 220 tons/month (based on 3-shift operation, suitable for nails/small parts). ● Condition: Complete, operational, and assessed as very good post-modernization. Key Components Included: ● Plating Barrels/Aggregates: 7 units (purchased new in 2021 for nail plating). ● Rectifiers (Total 7 pcs): ○ 6 units x 400A/1700A (Year 2017). ○ 1 unit x 800A (Year 2017). ● Plating/Rinsing Tanks (Total 17 pcs): Includes tanks for galvanizing, cascade rinsing (3- and 2-station), and passivation (Year 2006 per statement). Codpoxm Ttzsfx Ah Ujri ● Automation: Control Cabinet/Switchboard (Year 2018), Plating Hoists (Year 2016). ● Wastewater Treatment (LPW-ANLAGEN tanks): Scrubber, Fan, and complete Wastewater Treatment Station. ● Auxiliary Equipment (Modernization 2021): Full PE Acid-resistant Drip Tray under the line, Chemical Laboratory with equipment. Commercial Details: ● Documentation: Technical-Operating Documentation (DTR) available.

Condition: new, Year of construction: 2025, functionality: fully functional, total length: 7,000 mm, total width: 4,000 mm, total height: 3,130 mm, inner dimension height: 2,700 mm, inner dimension length: 6,900 mm, inner dimension width: 3,900 mm, Equipment: cabin, The automotive spray booth is a fundamental device in paint repair technology, enabling painting work to be carried out in safe and comfortable conditions while minimizing the negative impact on the surroundings and the environment. Specifications: - External dimensions: 7000 × 4000 × 3130 mm - Internal dimensions: 6900 × 3900 × 2700 mm - Entrance door: 3000 × 2600 mm (three-wing design) - Service door: 640 × 1800 mm - Structure: standard steel - Heat exchanger: standard steel - Panels: EPS polystyrene - Total power: 7 kW - Installation: indoor only Cabin Wall Structure: - Thickness: 50 mm - Insulation: EPS polystyrene - Color: white Cabin Base: - Cabin mounted directly on floor/concrete surface - Installation possible only indoors Double Roof: - Upper external layer: corrugated steel panels - Inner structure: partially grated Air Circulation System (Supply System): - Jet turbine 5.5 kW – 1 unit - Airflow capacity: 20,000 m³/h - Belt-driven system - Air recirculation control: none Lighting (Side Lights): - 20 side-mounted lamps - No option for ceiling lighting Air Heating System: - Single-stage Riello G10 oil burner, 54–120 kW - Manual burner control - Heating time: approx. 20 minutes Cabin Access: - Main Doors: - Dimensions: 3200 × 2600 mm - Three-leaf door system - Service Door: - Equipped with a separate service door Crodpfjxnbf Usx Ah Uoi - Pressure locks installed Filtration System: - Air intake: Pre-filter - Ceiling filter: Main high-flow filtration Filter Specifications: - Weight: 600 g/m³ - Thickness: 50 mm - Airflow: 900 m³/h - Capture efficiency: 97% - Air velocity: 0.25 m/s - Dust holding capacity: 650 g/m³ - Max temperature: 100°C - Filtration class (EN 779): M5 - Fire resistance (DIN 53438): F1

Year of construction: 2004, condition: excellent (used), functionality: fully functional, industrial oven VMD GRYGOV TKS 300°C Crjdpfjw Rb Snjx Ah Uoi 1.95 m x 2.4 m x 1.5 m internal dimensions air-mixed oven drying cabinet manufacturer: HV VMD GRYGOV TKS 080 EKZVO Year of manufacture 2004 Operating dimensions mm 1950 width x 2400 height x 1520 depth Ht Industry Programmable PID temperature controller volume: 7.2 m3 Temperature max. 300 ° C Air circulation: up to 2x 6120m3/h 2pcs heat-resistant radial fans 2x 1.5kw VNG315-4-1.5 Power supply Electric Nominal power 83 kW Voltage 380 V Frequency 50-60 Hz external dimensions: length:3400mm width: 2560+300mm height:3100mm door type: 2 door -Ex lock Warming up time 15-30 minutes (180° C) Homogenity

Condition: used, We are selling a used robotic grinding and polishing system. The system is in good used condition. The system includes: - 1x YASKAWA MH20 industrial robot with NX100 controller - 2x belt grinding machines for grinding belts with a circumference of 3,500 mm Codpexlufvjfx Ah Ueri - 2x polishing machines with oscillation and feed for polishing discs with a maximum diameter of 500 mm - 1x loading table for pallets with dimensions (LxW): 1,200 x 600 mm - 1x control cabinet If you have any questions, please do not hesitate to contact us!

Condition: new, Year of construction: 2025, functionality: fully functional, workpiece weight (max.): 700 kg, workpiece height (max.): 2,300 mm, workpiece length (max.): 6,000 mm, insulation material: Mineralwolle, insulation thickness: 150 mm, workpiece width (max.): 2,000 mm, Complete Plant with Chemical Pretreatment (7 Stages) for GSB Certification (QUALICOAT) (Suitable for Multimetal) All dimensions and further modifications can be taken into account during design and planning. The offer includes the following components: - Pretreatment cabin incl. reverse osmosis unit - Walk-in coating booth - Powder spray gun - Powder curing oven - Dryer - Manual conveyor system - Lifting-lowering station - Electrical control system Details: 1. Walk-in cleaning cabin, pretreatment for steel and aluminum The cleaning cabin is designed for automatic cleaning. Medium pressure spraying can be applied. The cabin contains 7 different spray tanks. Maximum part size: L = 6000 mm, W = 2000 mm, H = 2300 mm. 1. Cabin dimensions - Length: 6,500 mm - Width: 3,000 mm - Height: 3,600 mm 2. Total pretreatment dimensions - Length: 6,600 mm - Width: 4,640 mm - Height: 4,300 mm Process Stages: 1st Stage: Degreasing/Neutral Pickle - Heated tank, 50-55°C, time = 3-6 minutes, drip-off time = 80 seconds 2nd Stage: Acidic Mineral Pickle - Heated tank, 50-55°C, time = 3-6 minutes, drip-off time = 80 seconds 3rd Stage: Rinse 1 - Rinsing with ambient temperature, time = 0.75-1.5 minutes, drip-off time = 1 minute Csdsffv Tpjpfx Ah Ujri 4th Stage: Rinse 2 - Rinsing with ambient temperature, time = 0.75-1.5 minutes, drip-off time = 45 seconds 5th Stage: Rinse 3 - Rinsing with ambient temperature, time = 0.75-1.5 minutes, drip-off time = 45 seconds 6th Stage: Nano-Ceramic - Processed at ambient temperature, time = 0.75-1.5 minutes, drip-off time = 60 seconds 7th Stage: Overhead spray ring for post-rinsing after Stage 6 - Rinsing with ambient temperature, time = 1 minute, drip-off time = 60 seconds 8th Stage: Passivation, no-rinse for aluminum - Rinsing with ambient temperature, time = 2-3 minutes, drip-off time = 1-2 minutes 1.1. Reverse Osmosis Unit - Reverse osmosis system, 250 liters/hour 1.2. Oil Skimmer - Tank no. 1 is equipped with an oil skimmer "UniSkim-21-100". Construction: The spraying system is two-part and movable, and can be shifted up to 500 mm via a pneumatic sliding system. Return to the tanks is also mobile via a pneumatic sliding system with 7 positions in order to serve the 7 tanks. 2. Walk-in coating booth 1. Booth dimensions - Length: 7,400 mm - Width: 4,000 mm - Height: 3,236 mm 2. Booth dimensions incl. extraction system - Length: 8,552 mm - Width: 6,232 mm - Height: 4,393 mm The booth features 2 single-side pneumatic doors for entry/exit of workpieces, and an additional side door for the coater. 3. Powder Coating Equipment Wagner, Manual System "Sprint 2 B" 4. Powder Curing Oven - Internal dimensions: - Length: 6,500 mm - Width: 2,200 mm - Height: 3,416 mm 5. Dryer - Internal dimensions: - Length: 6,500 mm - Width: 1,200 mm - Height: 3,416 mm 6. Manual Conveyor System The conveyor system consists of: The conveyor system is designed for a crossbar weight of 700 kg. The carriage can carry a maximum of 2,000 kg on 3 rails.

Condition: excellent (used), functionality: fully functional, Complete equipment for an industrial paint shop: - Dry wall with extraction system and filters Cjdpfxoxmr Tye Ah Ujri - Mechanical conveyor for painted parts with hooks (modular construction, adjustable to the room) - WAGNER painting unit The paint shop was used for painting window frames.

Condition: used, Year of construction: 2017, functionality: fully functional, plating electronics GmbH Rectifier water-cooled Cjdpexlqy Njfx Ah Uori

Condition: new, functionality: fully functional, Year of construction: 2025, Detailed Specification: - Internal dimensions: 5500 × 1500 × 2300 mm (L × W × H) - External dimensions: 5700 × 1900 × 2700 mm (L × W × H) - Entrance doors: Double-wing, 1700 × 2300 mm (W × H) - Wall panels: Thickness 100 mm, width 950 mm, tongue-and-groove structure; steel sheet 0.5 mm with mineral wool insulation inside - Box: Panels 100 mm thick, filled with mineral wool - Heating system: RIELLO oil burner model 40G20; heating capacity 200,000 Kcal/h; heat exchanger made of 2 mm stainless steel - Maximum heating output: 200,000 Kcal/h, total 1 set - Roof: Panels 100 mm thick with mineral wool insulation inside - Control system: Heating control, time setting, fault indicator, emergency stop, hour counter, temperature limit regulator, total operating hours display - Total power: 6 kW Crsdpfexna U Ujx Ah Uei - Overhead conveyor system: 4 tracks; maximum load 400 kg each We can manufacture ovens of any required dimensions. We provide complete systems including transport traverses, spray walls, and powder coating guns — as shown in the photos.

Condition: new, Year of construction: 2025, Maintenance-friendly dedusting system specially developed for aggressive sandblasting dusts with pre-chamber impact separator, complete essentially consisting of: a) 1 cartridge dry filter, type PF 2.16.B250 for 30,000m³/h (other sizes available) each consisting of a stable, vacuum-tight 3 mm sheet steel housing, divided into the raw gas chamber with filter cartridges, filter pre-chamber impact separator and clean gas chamber with filter cleaning by means of compressed air, each with separate Easy Open maintenance door. Dust collection hopper with slotted valve or rotary valve for dust disposal using big bags. Solenoid valve control with differential pressure display for optimum adjustment of filter cartridge cleaning. Codjw Ivqmopfx Ah Uori Maintenance doors as swing doors Maintenance easy.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. Crodpfx Ahjwzl Hxs Uei * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2025, functionality: fully functional, temperature: 220 °C, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, Powder ovens in various sizes 1 Internal dimensions length 1500 - 6,500 [mm] 2 Internal dimensions width 1700 - 1,900 [mm] 3 Internal dimension height 2,000 [mm] 4 Substructure Steel profile 5 Walls 1 mm galvanized sheet metal on both sides, RAL on the outside 6 Insulation walls, ceiling rock wool 150mm 75Kg/m² 7 Oven floor receives 2 entry rails for rack trolleys (optionally with conveyor technology) 8 Temperature 220°C 9 Fans 1 - 2 pcs. 2600 - 15,000 [m³/h] 10 Electric motors 1 - 2 pcs. 1.1 - 6 [kW] , 1450 [rpm], 3 F, 50 [Hz] 11 Thermal output 14 - 99 [kW] Cjdsfhv Tlepfx Ah Uori 12 Sash or sliding doors on one or both sides 2 - 4 insulated with rock wool 150mm 75Kg/m² Indirect heating via thermoblock 13 Thermoblock stainless steel INOX AISI 316 Heating electric or gas heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection

Condition: used, Year of construction: 2017, functionality: fully functional, Mefiag Satilum filtration system Long Life Unit with control 3 units Credpfjxlqw Ujx Ah Uei Model: MPF 4500-PP-SY-POL3K-MP10-AUTOFLOW-BYP-B20H

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,850 mm, total length: 12,125 mm, total width: 5,150 mm, overall weight: 8,000 kg, warranty duration: 12 months, inner dimension height: 5,000 mm, inner dimension length: 12,000 mm, inner dimension width: 5,000 mm, Equipment: cabin, lighting, PAINT BOOTH 12x5x5M EZ Series Model: - LED ceiling lighting - LED side lighting - RIELLO oil burner - Four fans, including: ‎ ㅤ- 2x supply fans ‎ ㅤ- 2x exhaust fans TECHNICAL PARAMETERS: - External dimensions: 12125x5150x5850 mm - Internal dimensions: 12000x5000x5000 mm - Entrance doors: 4000x4800 mm (2 units, four leaves, reinforced hinges) - An additional BOX 1650 mm x 8000 mm should be included in dimensions – can be placed on either the right or left side. - Structure: galvanized steel frame Crsdpfx Aexm U Exeh Uoi - Heat exchanger: high-grade stainless steel - Panels: filled with mineral wool insulation - Drive-on ramps – 2 units - Fully grated floor The reinforced frame construction prevents vibration and the air surge effect from the main supply duct. Double Roof Design: - Upper outer layer - Inner truss structure with V600 ceiling filter Air Circulation System: - Supply system: Jet turbine 7.5 kW – 2 units - Exhaust system: Jet turbine 7.5 kW – 2 units Air Filtration System: - Pre-filter collects particles larger than 10 μm - Ceiling filter collects particles larger than 5 μm - Floor filter: Paint Stop - Carbon filter Lighting: - Ceiling lights: 52 LED tubes (14 angled fixtures with 4 tubes each) - Side lighting: 26 LED panels integrated into the right, left, and rear walls Burner: Riello – 2 units, oil model 40 G20, approx. 200,000 Kcal/h - Heat exchanger: high-quality stainless steel - Heating time: 8–15 min (max. 80°C) Optional Features: - Roof-mounted boxes - Insulated roof - Pass-through doors - Water curtain - Color according to RAL palette - Explosion-proof (EX) version available

Condition: new, Year of construction: 2025, Dedusting system with pre-chamber separator specially developed for aggressive sandblasting dusts, complete essentially consisting of: a) 1 cartridge dry filter, type PF 1.16.B250 15,000m³ (other sizes available) each consisting of a stable, vacuum-tight 3 mm sheet steel housing, divided into the raw gas compartment with filter cartridges and clean gas compartment with filter cleaning by means of compressed air, each with separate maintenance doors that are easy to open. Dust collection hopper with slotted valve for dust disposal using big bags. Solenoid valve control with differential pressure display for optimum adjustment of the 16 filter cartridges - cleaning. Technical data, approx. Type PF 1.16.B250 W x D x H 1.6 x 1.9 x 4.2m Air flow rate 15000 cbm/h Filter cartridges 16x 15,6m² Filter area 249.6 m² Filter medium PE fiber fleece Residual dust content 99.9% Codpfow Ivrwjx Ah Ueri

Condition: new, Year of construction: 2025, functionality: fully functional, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, 1. powder coating booth, open spray booth The overspray during powder coating is collected by the suction unit. The powder spray booth is supplied on castors and is therefore mobile. - The extraction unit is equipped with a 60 l powder container (rollbar). - There are 4 filters in the extraction unit as the 1st stage. - The absolute filter is located above the booth. 1 Dimensions of the powder level Width 2,450 mm Depth 2,350 mm Height 2,700 mm 2 fans 1 pc. 6,000 m³/h Electric motor 3.0 kW 3 Filter Ø 325x800 [mm] 4 pcs. type filter cartridges 4 Electromagnetic valves 2 pcs. 1" "Turbo" Italy 5 Absolute filter 1 pc. type pocket filter 2. powder combustion furnace 1 Internal dimension length 4,000 mm 2 Inner dimension width 1,500 mm 3 Internal height 2,200 mm 4 External dimension incl. thermoblock length 5,250 mm 5 External dimension incl. thermoblock width 2,050 mm 6 External dimension incl. thermoblock height 2,530/2,750 mm 3. switch cabinet Crsdpfxjffwfxs Ah Uoi 4 Manual conveyor system The "Mantion system" conveyor technology is designed for max. 250 kg per product carrier and 750 kg/ trolley.

Condition: new, Year of construction: 2025, Pressure blasting cabinet DSK 15.15.20.RB75 with or without roller conveyor. Blasting chamber W=1150 D=1150 H=930mm. 1 TÜV-tested pressure vessel 20l with conical outlet funnel. 1 blasting medium dosing valve with blasting medium quantity regulation pneumatically controlled. 1 built-in closing cone with guide tube. 1 compressed air connection with pneumat. Shut-off valve and branch for control air. 1 pressure regulator to adjust the blasting pressure. 1 blasting hose DN19. 1 handpiece with boron carbide blasting nozzle Venturi 8mm. 1 pair of blasting gloves. Dust extraction filter 2000m³/h 2,2kW Credpfxjga I R Es Ah Uji

Condition: new, Year of construction: 2025, Powder baking furnace 3,500 x 1,900 x 2,000 mm 1 Inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2.000 mm 4 Substructure 1 set of steel profiles 5 Walls 1 set of double-sided galvanized sheets 1mm, outside RAL Crjdpfx Ahefhv Tcs Uji 6 Insulation walls, ceiling 1 set rock wool 150mm 75Kg/m² 7 Floor furnace receives 2 drive-in rails for trolleys 8 Temperature 220°C 9 Fans 1 pc. 7.500 m³/hour 10 Electric motors 1 pc. 3 kW , 1450 U/m, 3 F, 50 Hz 11 Thermal power 58 kW 12 Hinged doors one-sided 2 pcs. insulated with rock wool 150mm 75Kg/m² Heating indirectly by thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electric heat-resistant fans and heat-resistant bearings, thermoblock has overheating protection 14 burner 1 pc. furnace is heated electrically 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Condition: new, Year of construction: 2025, Pressure blasting cabin DSK 20.10.09 with carriage and turntable. width: 2050mm depth: 935mm height: 955mm Pneumatic lifting door with the advantage that the abrasive falls into the cabin when opening the door and not on the floor. If you have any questions about technical specifications etc. please contact us in writing or by telephone. The basis of the machines is the production at the Grossenlueder site since 1971. Harth & Seifert - Georg Fischer - Schiffmann und Seidl - Oliver Fritz GmbH & Co. KG with the well-known contacts of many years. Codpfefnh Rvsx Ah Usri

Condition: new, Year of construction: 2025, Powder coating system for large parts All dimensions and other changes can be taken into account in the design and planning The offer includes the following components: Cabin for chemical pretreatment (3 zones) with spray ring Walk-in coating cabin Powder gun Powder firing oven Manual conveyor system Electrical control Example: (all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Walk-in cleaning cabin including automatic spray ring 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm height 4,200 mm Walk-in coating booth, manual coating 1 Dimensions of booth length 9,000 mm width 4,500 mm height 3,400 mm 2 Dimensions of booth including extraction length 10,125 mm width 4,500 mm height 3,400 mm powder firing oven 1 Internal dimensions length 6,500 mm 2 Internal dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 External dimensions including thermoblock length 7,600 mm 5 External dimensions including thermoblock width 2,800 mm 6 External dimensions including thermoblock height 3,100 mm Manual conveyor system The conveyor system consists of made of: 1. Support structure, consisting of steel elements, 120x120m/ IPE 160 2. Rollers - No. 9862 GL 4 pieces 3. Pneumatic accessories for locking - unlocking during transfer 4. Rail system - No. 9060 - 234 meters 5. Rollers - No. 9862 GLHT 24 pieces 6. Connecting pieces - No. 9061M 34 pieces 7. Fastening clamps - No. 9067/180 234 pieces Csdpfxobhh Awe Ah Usri 8. Stoppers - No. 9169 21 pieces 9. Movable locking - No. 9601 VM 6 pieces 10. Rigid locking - No. 9601 VF 17 pieces Electrical control The electrical control unit is divided into electrical and automatic control. With it we can control all the units mentioned above and consists of: - PLC - Touch screen 5" color -easy view- - Modem - Thermo-magnetic switch. Fuse (Telemechanique, Siemens, ABB). - Cables, supports, pipes, etc.

Condition: ready for operation (used), 20-foot sandblasting rental container with pressure blasting equipment, filter system, and safety equipment Cjdpfxoxl Dq Uj Ah Ueri

Condition: new, Year of construction: 2025, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Cedpfx Aeum Ufleh Ueri Chemical pre-treatment by spraying Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Electrical control system

Condition: new, Year of construction: 2025, functionality: fully functional, power: 88 kW (119.65 HP), temperature: 220 °C, heating capacity: 30 kW (40.79 HP), workpiece height (max.): 1,500 mm, workpiece length (max.): 500 mm, insulation material: Steinwolle, insulation thickness: 150 mm, workpiece width (max.): 500 mm, Scope of delivery: 1. chemical pre-treatment by spraying (in cycle process) 2. dryer 3. powder coating system 4. single powder oven 5. conveyor technology, semi-automatic 6. electrical control system Hall/ floor space Floor area of the system max. 12,000 x 6,500 mm Hall floor Industrial floor Workpiece sizes Max. Part dimensions L= 500mm, H= 1,500mm, W= 500mm Range of steel parts Conveyor technology P&F chain conveyor in cycle mode, semi-automatic Pre-treatment Chemical Power supply Cjdpeulwg Njfx Ah Uori Electricity On-site power (max. 88 kW) Gas On-site power Compressed air On-site power Water On-site power Calculation Type of system Cycle system Conveying speed 3.2 meters / min Length per cycle L = 1,600 mm Time for cycle movement: Tm = 1.6 meters : 3.2 meters/min = 0.5 minute Time for cycle standstill: Ts = 8.5-12 minutes Total time for cycle Tt = Tm + Ts = 9-12.5 min Electrical energy: Total power 88 kW min. Average consumption 60 kWh max. average consumption 70 kWh

Condition: new, Year of construction: 2025, Starter Packages Powder Coating Starter sets or individually designed packages for starting your own business in surface technology, e.g. for coating alloy wheels: The package includes two sample configurations for entering powder coating or expanding an existing business. Our focus is on customized consulting tailored to the customer’s budget and requirements. Modifications and special requests are standard with us. Proven, robust and low-maintenance technology is at the center of our offer. Set 1: - Powder curing oven, internal dimensions 2,000 x 1,900 x 2,000 mm - 150 mm thick mineral wool wall insulation for energy-efficient and cost-saving operation - 36 kW thermal output for rapid heat-up time - Oil, gas, or electric heating options - 6,000 m³/h recirculating air (2.2 kW) for efficient heat transfer to workpieces - Up to 220°C - Powder coating booth (open spray booth) Powder booth dimensions: - Width: 2,100 mm - Depth: 2,000 mm - Height: 2,200 mm - Fan: 6,000 m³/h, electric motor 3.0 kW for a clean working environment - Filters: 4 units, ø 325x600, cartridge type with interval-controlled self-cleaning - Secondary filtration via pocket filters - Powder coating system Wagner, manual system “Sprint 2 B” - Latest model from premium manufacturer Wagner for optimal coating results (other brands available upon request) - Corona manual gun - PEM-C4 Ergo - EPG-Sprint control unit - Powder feed system with Fluid Crown ST 550/10 - Powder injector PI-F1 - Equipment trolley with vibrating table Set 2: - Powder curing oven, internal dimensions 1,500 x 1,200 x 1,750 mm - 150 mm thick mineral wool wall insulation for energy-efficient and cost-saving operation - 14 kW thermal output for rapid heat-up time - Electric heating - 2,600 m³/h recirculating air (1.1 kW) for efficient heat transfer to workpieces - Up to 220°C - Powder coating booth (open spray booth) Powder booth dimensions: - Width: 1,200 mm - Depth: 1,100 mm - Height: 2,380 mm - Fan: 2,500 m³/h, electric motor 1.1 kW for a clean working environment - Filters: 2 units, ø 325x600, cartridge type with interval-controlled self-cleaning - Secondary filtration via pocket filters - Powder coating system Wagner, manual system “Sprint 2 B” - Latest model from premium manufacturer Wagner for optimal coating results (other brands available upon request) - Corona manual gun Crsdpfxjbqk Nbs Ah Uji - PEM-C4 Ergo - EPG-Sprint control unit - Powder feed system with Fluid Crown ST 550/10 - Powder injector PI-F1 - Equipment trolley with vibrating table