Used Second Operation for sale (31,695)

Condition: good (used), functionality: fully functional, pneumatic collet clamping device with collets Hjdpfszmm Dgex Af Aefk

Condition: refurbished (used), Year of construction: 2015, operating hours: 20,640 h, functionality: fully functional, overall weight: 24,500 kg, total width: 2,500 mm, Completely overhauled machine Single-shaft shredder, particularly suitable for secondary shredding and granulation of pre-shredded materials. Application: Commercial waste for thermal or material recycling, e.g., paper, cardboard, plastics and foams, rubber, leather, textiles, floor coverings, etc. Lindner Komet 2200 HP, overhauled in March 2026 Year of manufacture: 2015 Control cabinet with ABB frequency converter, dust-tight with recooler Control panel: complete Drive motors: ABB 2x200 kW Paintwork new / RAL: 5003/7001 Rotor bearings/pull-off sleeve/shaft seals: new Hedpfx Afjyu Unds Asfk Hydraulic unit: complete Total weight approx. 24.5 t Dimensions (LxWxH) mm: 5800 x 2500 x 3100 mm Inspection and trial run/test run possible by appointment. Delivery time: immediate

Condition: good (used), Year of construction: 2014, operating hours: 18,520 h, Single-shaft shredder, especially suitable for secondary shredding and granulation of pre-shredded material. Application: Commercial waste for thermal or material recovery, e.g. paper, cardboard, plastics and foams, rubber, leather, textiles, floor coverings, etc. Lindner Power Komet 1800 Year of manufacture: 2014 Control cabinet; complete with ABB frequency converter, Recooler Operator panel Hopper Drive motors: 200 kW Hfsdpjwxmb Eefx Af Ask Hydraulic unit: complete Total weight approx. 21 t Dimensions approx. LxWxH mm: 5000 x 2800 x 3000 mm Inspection: possible upon arrangement. Delivery time: immediate.

Condition: used, in perfect condition, with a brand new housing (replaced just last year). Hfodpfx Aeziz Swef Ask

Year of construction: 2023, condition: new, Coperion ZSK 27 MV Plus extrusion line. Application: Pet food and dental sticks. Year: 2023, never used, still in its original packaging. Hodpjxr Hgxefx Af Ajfk

Condition: repair required (used), Year of construction: 2014, functionality: not functional, machine/vehicle number: OP-2013-019*002, total length: 2,730 mm, total height: 3,192 mm, overall weight: 3,100 kg, total width: 1,752 mm, This is a two-rotor, slow-speed shredder from the manufacturer Automatica s.r.o., equipped with a new electric motor and a Nord gearbox. Unfortunately, the machine has a rotor shaft defect, but it is repairable. Hodpfx Aozgf R Sjf Ajfk It includes new stator and rotor blades. New electrical wiring, including a switchboard. Control via PLC, see photo. The shredder is designed for shredding wood, plastic, cardboard, etc.

Condition: used, Year of construction: 1989, System for the secondary filtration of beer after the Kieselguhr filtration. Operating pressure: 10 bar Operating temperature: 140 °C Volume: 169 l Length: 4,10 m Width: 1,30 m Height: 2,0 m Weight: 1700 kg Material: stainless steel Position: standing Base construction: Frame Features: Trap Filter, Beer filter, Water / CIP Filter, Unit for filter flushing and chemical regeneration. Hodpfjw Tmqbjx Af Ajfk

Condition: good (used), Year of construction: 1998, Motor power [kW]: 150 (2x75) Number of blades on the shaft: 48 (2x24) Blades [mm]: 80x80x45 mm (reinforced/extended mounting threads). New, square. 4 blades, of which 3 blades are 100% and 1 blade is approximately 70% new Rotor: Shaft width [mm]: 2,100 Number of shafts: 2 Shaft diameter: 500 mm Shaft speed [rpm]: 75-165 Screen diameter [mm]: 30 mm Chamber dimensions [mm]: 2,100 x 1,250 Hodpfxeibzbho Af Aefk Automatic start: Soft start Rated voltage: 3 x 400 V/50 Hz Rated current: 160 A-200 A Automation: Siemens Simatic Weight [kg]: approx. 14,500 Dimensions: Length [mm]: 3,850 Width [mm]: 2,720 Height [mm]: 2,700 Documentation: German 2014 A complete overhaul was carried out. A list of these parts and pictures are available upon request. This machine has not been used for several years (since then - one owner). Previously, it processed plastic, film, and cardboard - RDF after selective recycling. The approximate throughput for materials like the above (lightweight) is about 1-1.5 tons/hour. Other materials - to be checked/discussed. The machine was fully functional and is currently stored on site. Additional photos and video available upon request.

Condition: used, Year of construction: 1998, This model of machine is fitted with 2 independent sensitive hydraulic copy units that can work from either a template or sample. The first cutter would be set for roughing out, the second one for the finishing cut that will enable a component to be produced in one pass. There is still the possibility to programme a second automatic pass of the finishing gouge for heavy work. The machine is also equipped with hydraulic tailstock unit and hydraulic operated back knives. Year - 1998 CE The unique feature of the T5E is saddle movement by precision recirculating ball screw with programmeable electronic control to the feed speed to ensure optimum turning flexibility and quality. This precision feature allows the operator to perfectly control the saddle advance in relation to the complexity of the turning and the optimized saddle speed can then be stored within the memory of the machine. 2000mm turning capacity between centres Hodpszd Uv Eefx Af Asfk NC electronic control to saddle movement with infinitely variable feed 0 to 12m/min Two speed 4/5.5hp motor giving six spindle speeds 900-1500-1800-2250-3000-4500rpm Two Hydraulic Copy Units each mounted with horizontal vee type gouges hss 2 Vertical back slides with knives for making dowel ends Max 95mm x 95mm square section with revolving Steady Max 175mm x 175mm square section without Steady Sliding guard for operator protection CE safety equipment

Condition: used, Year of construction: 2016, operating hours: 12,000 h, functionality: fully functional, The last service by Asco was performed in December 2016 at 12,032 operating hours. Since then, the machine has only run for an additional 603 hours due to an investment in a brand new production line. The machine’s total operating time is 12,635 hours (12,032 h at last service + 603 h extra use). • The machine comes with complete documentation, including technical manuals and service reports. • Both the pump and the cylinder have been replaced. ASCO’s automatic dry ice machine produces slices of varying thicknesses and two pellet sizes (3mm and 16mm) at the push of a button. The dies for the different sizes are integrated and selectable via the touchscreen—manual changeover is not required. Theoretical output is up to 400 kg/h, depending on the type of product (block thickness or pellet size). According to the owner, the machine consistently produces at least 250 to 300 kg/h in practical use. New price: €160,000. Worldwide shipping available. Hfedpfxjy R I Uqs Af Ask Relevant keywords for search and sale: Cold Jet dry ice machine for sale, dry ice blaster for sale, industrial dry ice cleaning machine, CO2 cleaning equipment, Cold Jet Aero series, used Cold Jet, second-hand dry ice blasting machine, dry ice pelletizer, cryogenic cleaning, high-pressure dry ice blaster, refurbished dry ice blaster, 20 ft blasting hose, dry ice gun, venturi nozzle, Kärcher Ice Blaster, ASCO Jet, Cryoblaster, ICS, Nozzitec, Triventek, Cryonomic, Südstrahl, White Lion, ICEsonic, industrial cleaning equipment Europe, dry ice machine export, DrDryice. Contact for more details or to arrange an inspection.

Condition: used, mileage: 69,990 km, power: 77 kW (104.69 HP), fuel type: diesel, gearing type: mechanical, first registration: 01/2022, emission class: euro6, color: white, number of seats: 9, Equipment: ABS, air conditioning, central locking, navigation system, soot filter, Chat now via WhatsApp: Contact our sales consultant quickly and easily. Internal number 3378 Optionally available: * 12 to 64 months warranty (valid throughout the EU) * New inspection * New TÜV (German technical inspection) & emissions test * Nationwide delivery * Financing possible even without a down payment Hfodjzbzdrepfx Af Ask * Spring offer: Upon request and for an additional charge of only €999, the towing capacity can be increased to up to 3,500 kg (vehicle and manufacturer dependent). ----Vehicle highlights: * 19% VAT can be shown * Regularly maintained * German vehicle * Immediately ready for use * First owner * Euro 6 standard * Accident-free * 9-seater * Comfort seats * Cruise control * Air conditioning * Rear view camera * Bluetooth multimedia system * Trend equipment * Style package Special features: Audio system 21: Digital (DAB/DAB+) radio reception with 8" multi-function display, rear window wiper, configuration with specific central locking, visibility package 1, step under sliding door on the left, heat-protective glazing for the cargo/passenger compartment, medium tint level Additional features: Airbag on the passenger side, airbag on the driver's side, active curve light, anti-slip control (ASR), exterior mirrors electrically adjustable and heated, turn signal integrated into exterior mirrors, floor covering: rubber in the cargo/passenger compartment (complete), on-board computer, entry lights, electronic traction control, driving assistance system: hill start assist, driving assistance system: emergency brake assist, driving assistance system: crosswind assist, windows in the cargo/passenger compartment: fixed, 2nd row left, windows in the cargo/passenger compartment: fixed, 3rd row left, windows in the cargo/passenger compartment: fixed, 3rd row right, generator 240 A, grab handle B-pillar, grab handles in front, lockable glove compartment, rear wing doors with glazing, body/structure: standard station wagon, body variant: normal roof, radiator grille black, steering column (steering wheel) adjustable in height/length, model update, engine 2.0 L - 77 kW TDCi CAT, parking pilot system front and rear, radio preparation, 4 speakers, wheelbase 2933 mm, tire pressure monitoring system, spare wheel in driving condition, rear seat package 6 (single seat and double seat, 2nd and 3rd row), low emissions according to Euro 6d emissions standard, windshield wiper with intermittent operation, adjustable, headlights H4, sliding door cargo/passenger compartment right, mud flaps front and rear, side protection strips, seat package 13: driver's seat (4-way adjustable) - passenger double seat, fabric, steel rims 6.5x16, start/stop system, 12V socket in the cargo/passenger compartment, bumper partially painted, style color package, daytime running lights LED, Trend, lashing eyes (2), auxiliary heater electric, second key with folding remote control----Do you want to lease or finance? We offer attractive deals – even without a down payment! Feel free to contact us. Contact: Telephone: E-mail: Location: Nutzfahrzeuge West GmbH Rudolf-Diesel-Str. 2 45711 Datteln - Germany Opening hours: Mon-Fri: 9:00 a.m. - 6:00 p.m. Sat: 9:00 a.m. - 2:00 p.m.----Note: All information on the internet is non-binding and serves only as a general description of the vehicle. Errors, typos and prior sales are reserved. The binding condition of the vehicle results exclusively from the purchase contract on site or by written assurances. Vehicles with a mileage of ov

Condition: refurbished (used), Year of construction: 2022, functionality: fully functional, This is a pizza conveyor oven manufactured by Lincoln, model Counter Top CT 2512 - continuous belt, year of manufacture 2022. The oven has been professionally overhauled in our in-house workshop and is fully functional. The list price is: €8,998 net / €10,707.62 gross Our price: €4,159.66 net / €4,950 gross You will receive an invoice with VAT shown. Our used equipment service for you: 6-month warranty on electrical parts, limited to the replacement of defective parts, excluding installation and removal costs. High-quality branded equipment at fair prices. Professional overhaul/inspection and expert cleaning. Checked and fully functional - or your money back. Flexible shipping or self-collection options. Competent advice – before and after purchase. Provision of operating manuals, connection diagrams & spare parts. Inspection according to DGUV V3. Technical data: W x D x H: approx. 797 x 1269 x 457 mm Power connection: 400 V / kW: 6.1 / 50-60 Hz Exhaust air volume: 700 m³/h Temperature: adjustable up to 315°C Year of manufacture: 2022 Weight: 70 kg Belt dimensions: 410 x 1260 mm Baking area: 410 x 520 mm Belt speed: 30 sec - 15 min Output: 30-40 pizzas (26 cm diameter)/hour Baking time per pizza: 4 minutes Condition: used, overhauled, fully functional Hfodpfx Afszub Ezs Ajk Further details: High-performance conveyor oven for up to 40 pizzas per hour with a 4-minute baking time Smallest professional digital conveyor oven for space-saving and easy installation in front and back areas Ideal for heating, cooking, baking and preparing crispy products 4 programmable menu buttons Very high efficiency even at low temperatures thanks to impingement technology Temperature range from 32°C to 315°C freely adjustable Belt speed can be adjusted continuously (30 seconds to 15 minutes conveying time) Equipped with on/off switch and digital touch panel for temperature and belt speed control The conveyor oven replaces conventional kitchen equipment such as salamanders, griddle plates, fryers and ovens Perfect for front-of-house cooking areas due to stackability and mobile base (optional) The electric conveyor ovens are equipped with an innovative and easy-to-use digital control and digital display of temperature and time Shipping: Delivery or self-collection by arrangement Worldwide shipping on request Shipping to islands or mountain stations only by arrangement Subject to changes and errors Do you have any questions, would you like advice, or would you like to see something on-site? You can reach us by telephone during our opening hours: Monday-Friday 09:00 - 13:00 and 14:00 - 17:00. Sales are made exclusively according to our general terms and conditions (AGB).

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2014, laser power: 3,000 W, X Working area max.: 2500 mm Y Working area max.: 1250 mm Control: IndraMotion MTX Laser power: 3000 watts Standard equipment: Machine - Coordinate guide for high-precision machining - Stable, easily accessible C-frame - Linear magazine with 21 tool positions and 4 clamps - Drives with maintenance-free three-phase servo motors - Repositioning device with programmable hold-down device - Foot switch for clamp closing - Ball tables - 2 part flaps 500 mm x 500 mm - FocusLine - NitroLine - FastLine - Ejection cylinder for laser parts - Slag cone detection TRUMPF laser - TruDisk 3001 solid-state laser with 1 LLK outlet - Excitation via pump diodes - LLK according to standard layout (10m) - TruControl laser control 1000 - Cooling unit - Laser logbook function Cutting head - Solid-state laser compact cutting unit - ControlLine Punching head - Electro-hydraulic punching head - Rotatable mono tool holder - Tool length compensation - Programmable hold-down device (active / passive / repositioning) - Punch stroke counter and thread stroke counter - Spray lubrication of punch - Punch slug extraction - Calculation of filling level in the punching console - Level monitoring of thread forming and tool lubrication Control - Open control based on Rexroth IndraMotion MTX - Control panel with 17" touch control panel - Program management - Production plan - Integrated technology data - Teleservice via Internet - Programmable cutting gas pressure - Automatic switch-off with wake-up mode Data transfer - USB interface - RJ-45 network connection Safety - CE marking - Two-beam light barriers - Monitoring system for, among others Gas pressure, temperature, cooling water - Quick shutdown hydraulics - Protection against scattered radiation - Compact dust extraction system - MultiTool function - MultiBend function - Thread forming function - Engraving function - Deburring and rolling technology function - SoftPunch function - StripLine Hfjdoy Samuopfx Af Ask - Lowerable die - Spray lubrication die including level monitoring - Additional clamping claw - 4 pcs. Height-adjustable clamping claws - Vibration-damped installation - Chip conveyor with tilting container - Blow-out device for small parts - Warping detection SheetMaster - Unloading platform - Suction frame with 36 suction cups - Peeling suction cup - Vacuum sensors for each suction cup - Double sheet detector for double sheet control - Central lubrication - TRUMPF control based on Rexroth IndraMotion MTX - Automatic clamp closing machine - Loading and unloading parallel to production time - Peeling system including positioning aid medium format (2500x1250) - First additional suction cup package standard - Second additional suction cup package standard - Unloading monitoring laser parts GripMaster - Parts conveyor belt punching station - Parts conveyor belt laser station ToolMaster with 70 stations (only for punching operation) - ToolMaster set-up parallel to production time

Condition: used, mileage: 32 km, power: 110 kW (149.56 HP), first registration: 06/2025, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: automatic, emission class: euro6, number of seats: 2, total length: 5,531 mm, total width: 2,474 mm, total height: 2,740 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, Internal number: 4191.TZ25.PS18941---- Errors and omissions excepted! SPECIAL EQUIPMENT * Battery: AGM deep-cycle high-performance battery - 2 AGM batteries * Bi-Xenon headlights with static cornering lights, LED daytime running lights * Windows, 2nd row of seats: Sliding windows, left and right * Automatic climate control: Front air conditioning - Ford audio system with 12-inch multifunction display and Ford SYNC4 - Radio, DAB/DAB+ - FordPass Connect including live traffic information, WLAN hotspot - Audio controls on the steering wheel - Bluetooth, USB connection, hands-free system - Emergency assistance - Android Auto and Apple CarPlay - extended voice control * Programmable battery monitoring * Headlight low beam with static turning light * Interface plug * Seats: Deletion of rear seats Hfedpfoy Tr Aqjx Af Ask * Seat Package 27: Driver's seat with 4-way electric adjustment - Passenger single seat - Interior armrest - Lumbar support - Heated seats for driver and passenger - Seat upholstery: Fabric * Technology Package 13: Heated windshield - Windshield wipers with rain sensor - Parking assistance system front and rear, additional sensors on the sides - Active emergency braking assist (radar-based) - Lane keeping assist with driver fatigue warning and high beam assist, additional with lane keeping and lane change assist - Headlight assist with day/night sensor - Blind spot assist - Adaptive cruise control - Rear view camera - LED downlight - Fog lights - Exterior mirrors, electrically adjustable, foldable, and heated - Automatic climate control * Heat protection glazing, medium tint * Conversion to ambulance: Basic conversion NOVARIS (electrical wiring - laying of empty conduits - preservation and underbody protection) - Grey wooden floor - 230V system with priority circuit for inverter - Central electrical system with automatic climate control - NOVARIS roof fan - Comet LED warning light - Hänsch siren with city/country setting - Air4D auxiliary heater - Preparation for analog and digital radio - Fold-down wall seat with seat sensor - Ohlendorf intercom system - Börde step - Stretcher storage including fixing system - Loading ramp 2600x620 FURTHER EQUIPMENT * 1 battery * Airbag, driver and passenger side * ABS with electronic brake force distribution * Exterior mirrors, electrically adjustable and heated * Battery operating time, programming of battery operating time to 10 minutes * Floor, rubberized (in driver's cab and passenger compartment) * On-board computer with fuel consumption and mileage information * Headliner, complete * Double-wing rear door with 180° opening angle (with window) - with heated rear windows * ESP with traction control - Hill start assist - Side wind assist - Safety brake assist - Roll-over protection - Emergency brake assist including emergency brake light * Windows, 2nd row: Fixed side windows, left and right * Power windows with quick-up/quick-down function for driver's side * Ford Easy Fuel - comfort fuel filler flap and misfueling protection * Generator, high-performance version * Cruise control * Glove compartment with lockable lid * Interior lighting with delay circuit and reading lamps at the front * Fuel tank 70 l * Steering wheel: Artificial leather * Steering column, adjustable in height and reach * MyKey key system - individually programmable second key * Active emergency braking assist - (camera-based) * Emergency assistance * Parking assistance system front and rear * Particle filter: Diesel particulate filter *

Condition: used, Himmel HF120 mitre jointing machine for the precise and secure gluing of mitre joints in wooden frames, glazing bars and mouldings using white glue. The machine enables a fast setting time thanks to high-frequency technology, pneumatic clamping mechanisms and precise alignment of the workpieces. Ideal for furniture and picture frame manufacturing. Machine not in working order. Hfedpfxjztv D Aj Af Aek Technical data: - Cycle time: approx. 4 seconds - Strip width: max. 100 mm - Strip height: max. 100 mm - Operation: foot switch - Possible angles: 90°, 120°, 135°

Condition: used, Year of construction: 2020, operating hours: 2,000 h, machine/vehicle number: LC665, Technical Specifications & Performance DataThis Tetra Pak A3/Compact Flex aseptic carton filling and capping line is configured for Prisma Edge packaging in the 250 ml format. It combines carton filling, cap application and Helix handling equipment for compact beverage production and industrial packaging operations. The available equipment is designed around the Tetra Pak filling platform and Cap30 DreamCap closure system.Manufacturer: Tetra PakFiller model: A3/Compact FlexMaximum production capacity: 9600 BPHPack format: 250 ml Prisma EdgeAvailable configuration: filler, Cap30 capper and Helix equipmentOperating hours: 2000Machine year: 2020Advanced Automation & Control SystemsThe equipment includes line control for coordinated operation of the available filling, closure application and handling sections. A controlled line architecture supports consistent product flow through the filling and capping process while allowing the individual modules to operate as an integrated packaging system. The listed configuration includes Filler, LC40, ACHX30 and Cap30 components.Production Line Integration CapabilitiesThis equipment is suitable for integration into an aseptic carton packaging line. The available filler, capper and Helix sections can be positioned with compatible upstream product preparation equipment and downstream carton conveying, accumulation, coding and secondary packaging machinery. Its Prisma Edge format configuration makes it relevant for beverage production applications requiring 250 ml carton packs.Machine typeManufacturer / modelYearFilling MachineTetra Pak A3/Compact Flex2020Capping MachineTetra Pak Cap30 DreamCap2020Various EquipmentTetra Pak Helix2020Machine Condition & Maintenance HistoryThe line is reported as running, with 2000 operating hours. The stated availability is limited to the filler, capper and Helix equipment. This condition provides a practical basis for buyers planning a second hand aseptic packaging installation, line extension or replacement project within an existing industrial packaging environment.Operational Performance & VersatilityThe A3/Compact Flex platform is intended for high-output carton filling and closure application. The Cap30 DreamCap system is matched with the listed carton format, supporting a consistent filling-and-capping sequence for Prisma Edge packs. With a maximum stated output of 9600 BPH, the equipment can support structured beverage production where compact retail carton formats are required.Installation Requirements & Site PreparationInstallation should be planned as part of a complete aseptic carton packaging layout, with appropriate product supply, utility connections, hygienic process interfaces and downstream pack handling. Site preparation should allow access for operation, cleaning, maintenance and format-specific material handling. Compatible line controls and conveying should be assessed when integrating the available modules into a used bottling line or broader industrial packaging... Hfedpfxszucgms Af Ask

Year of construction: 1993, condition: used, Two-stage plate heat exchanger. First stage - Heating: hot water / product Product inlet approx 61-62°C, outlet approx 72°C, flow rate 600 hl/h; Hot water inlet approx 72,5°C, flow rate 750 hl/h Second stage - Regeneration: product / product Product inlet approx. 0-4°C, product outlet approx. 61-62°C, flow rate 600 hl/h; Product inlet approx. 72°C, product outlet approx. 11-14°C, flow rate 600 hl/h Additional title: 2-stage heat exchanger Capacity: 600 hl/h Hot water: 750 hl/h Operating pressure: 21 bar Operating temperature: 100 °C Length: 2,15 m Hfodpfxeztzcke Af Aek Width: 0,95 m Height: 2,15 m Weight: 5000 kg Material: EPDM HT / NBR / 1.4439

Condition: used, Year of construction: 2004, The system is connected to a repacking system and is used to supply full module boxes and return empty ones. For this purpose, pallets with full module boxes are placed on the left-hand roller conveyor (as seen by the forklift driver), fed to the system and unstacked on a conveyor belt next to the pallet. The modular crates pass through the repacking system, return empty and are stacked on pallets on the second roller conveyor and removed. Additional title: Depalletising of full module crates and repalletising of empty module crates Output approx.: 300 crates/h Length: 5,70 m Width: 4,30 m Formats: Bottle crate (400 x 300 mm) on Euro pallet (1200 x 800 mm) Operation / Control: on-site control device / Simatic S7-300 Position: free standing Base construction: Vierkantrohr-Konstruktion mit dem Boden verschraubt Hedpfxoztyv Nj Af Aofk Features: Pallet conveyors, gripper head for palletizing and depalletizing, box transports, frame construction with protective grille, control cabinet, operating device Layer patterns: 2x4 crates / 5 layers

Condition: ready for operation (used), Year of construction: 2004, operating hours: 615 h, spindle motor power: 22,000 W, spindle speed (max.): 5,000 rpm, travel distance X-axis: 580 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 1,045 mm, total height: 2,597 mm, total width: 2,060 mm, overall weight: 9,700 kg, controller manufacturer: MAZATROL, controller model: PC FUSION CNC 640MT Pro, product length (max.): 3,820 mm, number of axes: 5, This 5-axis Mazak INTEGREX 200 III S was manufactured in 2004. It features a maximum turning diameter of 660 mm and a maximum workpiece weight of 150 kg. The machine is equipped with a tool magazine capacity of 80 slots and a rapid traverse speed of 38 m/min on the X and Z axes. If you are looking to get high-quality turning and milling capabilities, consider the Mazak INTEGREX 200 III S turn-mill centre we have for sale. Contact us for further details. - Max. Swing Diameter: 660 mm- Max. Turning Diameter: 660 mm- Max. Turning Diameter over Slide: 500 - 660 mm- Max. Bar Working Diameter: 51 mm- Max. Workpiece Weight (incl. Chuck) - Chuck Workpiece: 100 kg- Max. Workpiece Weight (incl. Chuck) - Shaft Workpiece: 150 kg- Main Spindle Speed Range (Stepless): 35 - 5,000 rpm- Main Spindle Drive Power (30 min. rating / 100% continuous operation): 22 kW / 15 kW- Main Spindle Max. Torque: 349 Nm- Main Spindle Nose: A2-6"- Main Spindle Bore: Diameter 76 mm- Main Spindle Chuck Diameter: 210 mm- Main Spindle Indexing (C-Axis): 0.0001°- Second Spindle Drive Power (30 min. rating / 100% continuous operation): 18.5 kW / 15 kW- Second Spindle Speed Range: 35 - 5,000 rpm- Second Spindle Max. Torque: 326 Nm- Second Spindle Indexing (C-Axis): 0.0001°- Second Spindle Chuck Diameter: 210 mm- Tool Turret Design: Single spindle turret for stationary or driven tools- Driven Tools (IPM Motor) Drive Power (20% ED): 15 kW- Driven Tools Max. Torque: 120 Nm- Driven Tools Speed Range: 15 - 12,000 rpm- Tool Taper: MAZAK KM 63 quick-change system (for stationary tools)- Tool Magazine Type: Drum type- Tool Magazine Capacity: 80 slots (equipped for stationary and driven tools)- Tool Weight: max. 10 kg- Tool Diameter: max. 90 mm- Tool Diameter (with free adjacent slots): max. 125 mm- Tool Length: max. 300 mm- Tool Change Time (Tool-to-Tool step 1): approx. 1.3 s- Travel Y-Axis: +/- 80 mm- Travel W-Axis: 1050 mm- B-Axis Swivel Range: -30° to +195°- Rapid Traverse Speed X-Axis: 38 m/min- Rapid Traverse Speed Y-Axis: 26 m/min- Rapid Traverse Speed Z-Axis: 38 m/min- Rapid Traverse Speed W-Axis: 30 m/min- Rapid Traverse Speed C-Axis: 400 rpm- Feed Range X-Axis: 0 - 8,000 mm/min- Feed Range Z-Axis: 0 - 8,000 mm/min- Feed Range Y-Axis: 0 - 8,000 mm/min- Coolant Tank Capacity: 220 L- Pump Delivery Rate: approx. 20 l/min- Pump Pressure: approx. 5 bar- Pump Power: 635 W- Connected Load: 61.4 kVA- Operating Voltage: 400 V / 50 Hz- Pneumatic Pressure: 5 bar, 500 l/min- Total Operating Hours: 3,520 hours (Recorded on 2026/05/04)- Automatic Process Time: 1,581 hours- Automatic Cutting Time: 1,267 hours- Pure Cutting Time: 905 hours- Operating Time: 615 hours- Standard Accessories / Additional Equipment:- B-Axis (0.0001° positioning axis)- C-Axis (0.0001°)- Y-Axis- Spindle orientation on second spindle- Synchronization of main and second spindle- Hydraulic 3-jaw chuck diameter 210 mm, Type KITAGAWA B-208, including 1 set of soft jaws (Main Spindle)- Hydraulic 3-jaw chuck diameter 210 mm, Type KITAGAWA B-208, including 1 set of soft jaws (2nd Spindle)- Dual foot switch for opening/closing the chucks for main and 2nd spindle- Feedback of chuck status (open/closed) for main and 2nd spindle- Air blow-out device on chuck (Second Spindle)- Tool Setter (Tool Eye)- Front door interlock- Complete coolant system- Coolant and chip guard via fully enclosed work area- Work area lighting- Chip Conveyor System (Mayfran ConSep unit visible) Hjdszr U Aujpfx Af Asfk Technical Specification Counter Spindle Yes

Condition: used, mileage: 94,752 km, power: 79 kW (107.41 HP), first registration: 01/2020, fuel type: diesel, overall weight: 3,000 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total width: 2,032 mm, total height: 1,958 mm, Year of construction: 2019, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, Errors and prior sale excepted! Internal number: 0418. GW22KJ68712 ---- ADDITIONAL EQUIPMENT - 6-speed gearbox - Electronic ABS with EBD - Driver's airbag - Electrically adjustable and heated exterior mirrors - On-board computer - Flat roof - Headliner in the driver's cabin Hsdpfozthtijx Af Asfk - Double-wing rear door/180° (without window) - Rev counter - Electronic safety and stability system - Windows, 2nd row: fixed side windows - Electrically operated windows, front - Ford Easy Fuel - Generator, 240 A - Cruise control, leather steering wheel - Halogen projector headlights with LED daytime running lights - Grab handle B-pillar - Glove compartment with lockable lid - Interior lighting with delay function - Air conditioning, front - Paintwork: solid paint - Cargo area lighting - Adjustable steering column - Emergency brake assist incl. emergency brake light - Package: Style color package - Incl. fog lights - Particle filter: diesel particulate filter - Radio: Audio system 12 - Wheel covers - Wheels: spare wheel, steel wheel - Wheels: steel 6.5 J x 15 with 215/65R15 tires - Automatic sliding door entry light - Sliding door: sliding door, right with window - Mud flaps, front and rear - Side protection strips - Half-height side paneling - Power steering - Seat belts - Seats: 2nd row, 3-seater bench - Seats: Seat package 13 (Custom DOKA Trend) - Start-stop system - Socket: 12-volt socket - Front bumper in vehicle color - 4 lashing eyes - Immobilizer - Heat-insulating glazing, lightly tinted - Central locking with remote control - Auxiliary heater, electric - Second key with remote control ... and more. ---- The vehicle has not been detailed! Nationwide delivery is possible for an additional charge. Errors and prior sale excepted. We will gladly take your vehicle in part exchange. Financing/leasing is also possible without a down payment! Do you have any further questions? We will be happy to advise you!

Condition: new, machine/vehicle number: GSH, The ZERMA GSH series granulators are exceptionally robust machines designed for the most demanding applications and tailored to the diverse requirements of modern recycling operations. The housings, constructed from heavy-duty steel and welded for maximum strength, withstand even extreme loads. All assemblies related to bearing support, knife mountings, and the rotor shaft are significantly oversized, resulting in outstanding durability. With simple reconfiguration, the machines can effortlessly shred both massive lumps, thick-walled pipes, and also hollow bodies or films. Depending on specific requirements (including for temperature-sensitive materials), various rotor designs are available, all featuring the advanced and superior V-cut technology. All GSH series machines consistently deliver high-quality regrind – whether processing bottle crates, profiles, sheets, films, start-up lumps, or pipes. They are economical, exceedingly reliable, easy to clean, and built for long service life. When combined with ZERMA’s extensive range of options and accessories—such as extraction systems, conveyor belts, metal detectors, fine particle separators, roll-feed devices, etc.—as well as spare parts, the result is a custom-optimized size reduction solution. The advantages include significantly reduced costs, time, and personnel requirements. Thoughtful machine housing design The housing is centrally divided at an angle, and the upper section with feed hopper can be opened hydraulically, providing unrestricted access to the rotor for knife changes and cleaning. The screen insert is also held in place by a hydraulically swiveling screen cradle, ensuring optimal accessibility for quick removal and installation. The screens are reversible. Hsdpfx Afeyr Thde Aefk Rugged external bearing arrangement Another well-conceived design feature is the external bearing arrangement. Heavy-duty rolling bearings in steel bearing housings guarantee long service life and are ideal for even the toughest demands. The external bearings prevent grease from entering the cutting chamber, as well as preventing regrind or fine particles from getting into the bearings. This offers a distinct advantage, particularly during wet operation. Flywheel To absorb shock loads during granulation, an optional flywheel is available. For this purpose, the rotors are supplied as standard with a second shaft end. High operational safety All granulators conform to EU machinery directives and carry the CE mark. Accident prevention is ensured, for example, by run-down safety devices with limit switches, as well as hydraulically unlockable non-return valves.

Condition: used, Year of construction: 2009, machine/vehicle number: FA72, Technical Specifications & Performance DataThe SMI TF350 is a tray packaging machine designed for the secondary packaging of PET bottles. Built in 2009, this industrial packaging machine forms bottle packs into trays for efficient handling, transport, and distribution within a used bottling line. It provides a practical solution for beverage production facilities requiring dependable end-of-line packaging equipment.Manufacturer: SMIModel: TF350Year of manufacture: 2009Production capacity: 45-50 packs/minContainer handling: PET bottlesAdvanced Automation & Control SystemsThis tray packer is intended for automated packaging operations, supporting the organized grouping of PET bottles into tray configurations. Machines of this type are integrated with synchronized product infeed and discharge systems to maintain consistent pack flow through the secondary packaging stage. The TF350 can support streamlined operation in industrial packaging environments where repeatable pack formation is required.Production Line Integration CapabilitiesThe SMI TF350 can be positioned downstream of filling, capping, labeling, and bottle conveying equipment in a PET bottling line. It is suited to beverage production layouts where filled bottles must be grouped and prepared for palletizing or further distribution. Its capacity of 45-50 packs/min enables integration with appropriately matched upstream and downstream equipment.As a second hand tray packaging machine, it can be considered for line upgrades, replacement projects, or the expansion of existing bottling equipment. Correct integration requires compatible bottle conveyors, pack discharge handling, tray supply arrangements, and coordination with downstream palletizing or warehouse logistics systems.Machine Condition & Maintenance HistoryThe machine is in very good condition and has been regularly maintained. Extensive annual overhauls have been carried out by the manufacturer, supporting continued operational reliability. The tray packer remains in production until September 30, 2026, demonstrating that it is part of an active packaging process prior to dismantling.Operational Performance & VersatilityDesigned specifically for PET bottle handling, this tray packaging machine supports the secondary packaging stage of beverage production. Tray packing helps create stable, manageable bottle groups for storage, transport, and subsequent pallet handling. The machine is suitable for producers seeking used bottling line equipment that supports organized end-of-line operations without changing the primary filling process.Its role in industrial packaging is to convert a continuous flow of bottles into defined tray-packed units, improving product handling between production and distribution stages. Final pack configuration and compatibility should be coordinated with the bottle format, tray design, conveyor layout, and required downstream logistics flow.Installation Requirements & Site PreparationInstallation should be planned around the existing bottle conveyor route and the required infeed and discharge elevations. The machine is scheduled for dismantling and loading between October 7 and October 10, 2026. Site preparation should include adequate acc... Hedsztwl Uepfx Af Asfk

Condition: used, Year of construction: 2009, machine/vehicle number: FA71, Technical Specifications & Performance DataThe SMI SK450 T is a shrink wrapping machine for PET bottles, designed for secondary packaging applications within a used bottling line. Manufactured in 2009, this second hand unit includes a heating oven for controlled shrink-film processing and bundle formation. It is configured for industrial packaging operations requiring stable, transport-ready bottle packs.Manufacturer: SMIModel: SK450 TYear of production: 2009Capacity: 45 packs/minuteContainer type: PET bottlesIncluded equipment: Heating ovenPackage configurations: 0.5L in 3x3, 0.75L in 2x3, and 1.5L in 2x3Advanced Automation & Control SystemsThis shrink wrapping machine is intended for coordinated operation in an industrial packaging environment, where bottle infeed, film handling, heat shrinking, and discharge must remain synchronized. Its operating setup supports repeatable bundle production for the stated PET bottle formats. Installation and commissioning should include verification of the existing control interface, electrical connection, conveyor synchronization, and heating-oven operating parameters.Production Line Integration CapabilitiesThe SK450 T can be positioned downstream of filling, capping, labeling, or accumulation equipment to create multipacks for distribution. In a beverage production line, shrink wrapping provides a practical secondary-packaging stage between bottle handling and palletizing. The machine is suited to PET bottle bundles in 3x3 and 2x3 arrangements, allowing the line to handle the documented 0.5L, 0.75L, and 1.5L formats.For integration into a used bottling line, upstream and downstream conveyors should be matched to the machine's infeed and discharge flow. The heating oven forms part of the packaging process and should be assessed together with film transport components, bottle guides, and pack transfer arrangements during installation planning.Machine Condition & Maintenance HistoryThe machine is in production and remains operational until 30 September 2026. It is described as being in very good condition, with regular maintenance and extensive annual overhauls carried out by the manufacturer. This maintenance history is relevant for buyers seeking second hand bottling equipment with documented attention to operational continuity and packaging performance.Operational Performance & VersatilityWith a stated output of 45 packs per minute, the SMI SK450 T supports efficient shrink-film bundling of PET bottles for industrial packaging. The documented pack patterns provide flexibility for common beverage production formats, including compact 0.5L bundles and larger 0.75L and 1.5L bottle configurations. Shrink wrapping helps produce stable multipacks suitable for handling, storage, and onward palletizing.Installation Requirements & Site PreparationSite preparation should provide sufficient space for the shrink wrapper, heating oven, safe material flow, and access for operation and maintenance. The installation layout should account for bottle conveyors, film supply, bundle discharge, and connection to downstream packaging machinery. Electrical services and any required line utilities should be checked... Hfedpfoztwl Iex Af Aok

Condition: used, functionality: fully functional, Year of construction: 2025, load capacity: 6,000 kg, lifting height: 30,000 mm, fuel type: diesel, mast type: telescopic, fork length: 1,200 mm, drive type: Diesel, Telescopic handler, rotating Mast type: Telescopic Technical condition: New Front tire type: Pneumatic Front tire condition: 80 - 100% Rear tire type: Pneumatic Rear tire condition: 80 - 100% Description: The vehicle will be inspected according to UVV regulations. A&M pallet fork carrier set including pallet forks 1200mm, pallet fork carrier plate 1500mm and load hook 5t. Hfodpjw Eqdwsfx Af Aek 3rd valve, 4th valve, heater, STVZO compliance, full cabin, CE certificate, PEGASUS60.30St.V, TÜV/Dekra approval, 20 km/h, axles for construction machinery with automatic 45% differential lock on the second axle, additional platforms for outriggers, pair of LED spotlights on the rigid boom, 7-pin socket on the upper carriage, set of radio pre-wiring with antenna and speakers, standard carrier plates for tools, mechanically sprung Grammer seat with dual joystick, right joystick with integrated FNR and electrical pre-wiring for equipment with 3 movements, wheel set with off-road tires 18R22.5XF MICHELIN, semi-automatic air conditioning, detachable windshield protection for the cabin, kit for operation during upper carriage rotation of 180 degrees, boom vibration damping, integrated rear view camera with 7" display (not compatible with 7" monitor with digital camera on the telescopic boom), telematics kit (DTS), road spotlights (front) with LED daytime running lights, cabin with front windshield made of laminated glass, pre-wiring for Woodcracker saw, three-sided personnel basket 120x240cm, hydraulically extendable to 420 cm. Load capacity 300 kg, pallet fork carrier plate including load hook A&M, width 1.50m including pallet forks FEM4A, forks: 150x50, length 1.2m, load capacity.

Condition: used, Year of construction: 2008, machine/vehicle number: DEPAL43, Used TMG VEGA 60 automatic Depalletizer 5000 BPHTechnical Specifications & Performance DataThis Automatic Depalletizer VEGA 60 is a robust solution engineered for reliable bottle handling in industrial packaging environments. Manufactured by TMG, it supports efficient unloading of bottles from pallets and integrates automatic interlayer management for streamlined operation. With a production speed of 5000 bph, it is well-suited for medium-capacity beverage production and used bottling line applications. Its design ensures consistent performance for Glass containers, particularly in 1.5L formats.Manufacturer: TMG Model:VEGA 60 Year: 2008Production speed: 5000 bphBottle formats: Compatible with 1.5L bottle formatsContainer types: Designed for Glass bottle handlingAutomation: PLC-controlled operationSafety: Electronic safety barrier Interlayermanagement: Tier-sheet magazine with automatic interlayer removal; can remove protective hoods from the same magazine Advanced Automation & Control Systems The VEGA 60 features PLC-based automation for precise and repeatable operation across shifts. The control logic enables smooth layer-by-layer depalletizing, coordinated motions, and clear fault diagnostics. The electronic safety barrier provides active operator protection, ensuring safe access during setup and maintenance while maintaining productivity. Quick settings allow fast adaptation to standard 1.5L bottle handling and efficient start-up after pauses.Production Line Integration CapabilitiesThis depalletizer integrates easily within new or second hand bottling equipment configurations. It can operate as a standalone depalletizing module or inline with conveyors, accumulation tables, rinsing machines, and downstream filling, capping, and labeling machinery. The automatic tier-sheet handling reduces manual intervention between layers, improving flow to subsequent packaging machinery. Its design supports Glass bottle logistics, making it a flexible choice for beverage production lines handling water, juice, beer, or wine in compatible formats.Machine Condition & Maintenance HistoryProfessionally engineered by TMG in 2008, this machine is presented as a second hand industrial packaging asset suitable for immediate integration once installed and commissioned. The PLC control and robust mechanical design contribute to predictable maintenance intervals and long service life.Operational Performance & VersatilityAt 5000 bph, the VEGA 60 is ideal for medium-output operations seeking dependable depalletizing performance. Automatic interlayer and hood removal minimize manual handling, reducing changeover time between pallet layers and enhancing workplace safety. The system is optimized for 1.5L bottles and supports Glass containers, aligning with a wide range of beverage production requirements and used bottling line upgrades.Installation Requirements & Site PreparationThe depalletizer requires adequate floor space for pallet infeed, tier-sheet magazine access, and discharge conveyor alignment. Power supply must match the PLC and drive requirements, and provision for compressed air may be needed for actuators and safety systems. A level, reinforced floor and clear operator access paths are recommended t... Hfedszc Hqyopfx Af Aok