Condition: used, Speed-Tech Equipment horizontal cardboard baler, bales are approx. 1200 lbs., 6' long x 36" wide x approx. 28" tall, 3 phase, in working condition, winning bidder responsible for proper removal. Hpjdpfoxd D Nzex Af Doa

Condition: good (used), Year of construction: 2019, machine/vehicle number: 25653, Equipped with: -Automatic Central Lubrication System -Machine Guard -Indramat - MTX and Sercos CNC Control -The standard machine is equipped with CNC-control make Indramat - MTX and SERCOS-interface -Tool Dressing (Automatic dressing cycle of the dressing master and honing wheel tip diameter by a diamond coated dressing roll. The dressing cycle of workpieces can be pre-selected) -Electronic Indexing Unit -Operator and Maintenance Manual -All Electrical Drawings -PLC Language in English -Software and Hardware for Remote Diagnosis -High Precision Control of the Stock Allowance Material -Manual Loading on Spindle for Prototypes -Software for Infeed Optimized Cycle Type Reduction (Adaptive Honing) -Software for Vario Speed Dressing -Software for Calibration of Master Gears -Software for Timing Gears (including additional sensor for the hole of 4mm) -Software for Shortening of Workpiece Change-Over Time -Clamping Cylinder -RITTAL Cooling Unit -Lighting for Working Area -Installation of Vibration Detecting Sensors -Coolant Unit -Electrostatic Oil Mist Exhauster IFS With Rigid Piping -Internal Automation -Pallet Ring Conveyor System FlexLink (L-form shape see approved layout) -Parallel - Double Gripper Hsdpfx Ajw Iquyof Dopa -Pick and Placer Between Pallet Conveyor and Internal Loader -Extended Loading Length of the Pick and Placer Specifications: Workpiece: -Part Diameter: 20-150 mm -Maximum Face Width: 70 mm -Part Weight: 20 kg -Number of Teeth: 6-150 -Module: 1-5 mm Workpiece Spindle: -Maximum Speed: 6000 1/min -Installed Power: Approx. 25 kW Tool: -OD of Honing Wheel: 270 mm -Widths of Honing Wheel: 20-70 mm -Honing Wheel Material: Ceramics Tool Spindle: -Maximum Speed: 2000 1/min -Installed Power: Approx. 25 kW Machine: -Total Connected Load, Approx: 70 kVA -Floor Space (w x l x H): -Total Weight, Approx: 11 Ton -Bosch Rexroth MTX Control CML 85 Longitudinal Slide, Z-Axis: -Linear Drive -Drive Torque: 3,700 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 400 mm Cross Slide, X-Axis: -Linear Drive -Drive Momentum: 2,150 Nm -Infeed Speed: 60 m/min -Theoretical Infeed: 200 m/min -Drive Length, Maximum: 1050 mm Swiveling Axis, W-Axis: -AC-Servo Drive: 10,000 1/min -Setable Gear Transmission: i=5000:1 -Swiveling Angle: -90 Degrees / +16 Degrees Workpiece Spindle, C-Axis: -Direct Drive, Maximum RPM: 7,000 1/min -Drive Power: 30 kW -Drive Torque: 112 Nm -Digital Measuring System Tool Spindle, B-Axis: -Direct Drive (hollow spindle drive), Maximum RPM: 2000 1/min -Drive Power: 30 kW -Drive Torque: 150 Nm -Digital Measuring System

Condition: excellent (used), Year of construction: 2004, operating hours: 1,000 h, functionality: fully functional, turning diameter over cross slide: 380 mm, turning length: 350 mm, turning diameter: 200 mm, travel distance X-axis: 240 mm, rapid traverse X-axis: 12 m/min, Hembrug Mill-Turn Machine Model: Slantbed Mikroturn 100 CNC Siemens 840D Control Approximate Actual Run Time Hours: 1,000 Hydeostatic Spindle Hydrostatic Ways Scale Feedback Suspended Granite Bed Garnite Spindle Housing Coolant Pump Coolant Circulation Pump Pneumatic Bearing Purge Hydraulic Temperature Control Coolant Temperature Control Return Oil Pump and Reservoir for Remote Location of Hydraulic / Cooling Unit. Options & Additional Purchased Features: Tailstock Vacuum Pump for Vacuum Chucking Programable Controlled Spray Mist C-Axis Milling / Drilling Renishaw Tool Touch Probe Non-Contact Tool Incoming Air Dryer / Filter Thousands of Dollars of Brand New Tooling: Live Center Tailstock Taper Adapter 8” Micro-Centric Pneumatic Chuck 3 Sauter Straight Live tooling heads 2 Sauter 90 degree Live tooling heads 1 Special VDI offset Tooling holder 16 VDI Tool Holders for Turning, boring, and on center drilling. Tool Pick-up Video System Additional Backup Hard Drive with Software Fully Loaded and Tested. Extra Siemens Control Pannel Complete Set of Manuals Machine Upgrades I added at additional cost. New Digital Hard Drive New Backup Hard Drive with software already loaded, plug and play ready, no downtime. Hjdpfjwcfgbex Af Dopa New Z-Axis Heidenhain Scale Rewound Hydraulic Pump Motor, factory motor was running too hot for my liking. Replaced Operator Panel, back light on monitor went out, have the original, back light needs replacing. 50 Foot Extended Wiring Harness For Remote Location of Hydraulic / Cooling Unit.

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Cutting Area: 3000*1500mm Cutting Speed: 0-40000mm/min Hedpfxjhv Hkao Af Depa Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Cutting Thickness: 0-30mm CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, QRP26 Automatic Mesh Welding Portal inclusive of: • Tooling for 49 line wires • Top and bottom electrodes and current distribution • Pneumatic weld presses x 25 (Parallel/Direct Weld Triplex) • Transformers 250kvA x 13 • Weld controllers • Electrical panel • Programming computer • 2500mm (100”) wide Hpjdpfxjxgg T Uj Af Dea Including PLL 26 automatic linewire picking and loading system.

Condition: used, Nelmor 1436 grinder with a 100 HP, 3 phase motor, and approx. 15' 9" screw auger, winning bidder responsible for proper removal. Hpjdpfexd D Nusx Af Dsa

Condition: good (used), Year of construction: 2001, Equipped with: Power Stock Fanuc 5-Axis CNC Control 160M 400mm Honing Wheel X Axis Pulse Generator Coolant System w/Twin Filters Magnetic Chip Separator Honing Tool Set up for Last Job is Still in Machine Internal Diameter of Honing Tool on Machine is 14" Work Light Power Door Auto Dress 5-Part Program Hpjdpferualpex Af Dja Instruction Book for 16M Control Instruction Book for Set-Up and Operation Specifications: Maximum Outer Diameter: 250 (350) Minimum Outer Diameter: 30 Maximum Overall Length: 400mm Maximum Tooth Width: 45mm Module: 1.0-3.0 Cross Feed Device(Z Axis): 430mm Max. Travel Honing Wheel Cutting Feed Device(X Axis): 370 Max. Travel Honing Wheel Swing Device(C Axis): Swing Angle: +30 Degress Honing Wheel Rotation Drive Device(A Axis): Honing Wheel Spindle Speed R/Min: 500 Honing Wheel Outer Dia.: 300 (400) Maximum Honing Wheel Width: 50mm Crowning Device (Y Axis): Maximum Rocking Angle: 1.6 Degrees Motor Types: Z-Axis Drive Motor: 1.8Kw X-Axis Drive Motor: 1.8Kw Y-Axis Drive Motor: 0.7Kw C-Axis Drive Motor: 1.8Kw A-Axis Drive Motor: 2.2/3.7Kw Maximum Distance Between Centers: 600mm Center Height: 1,100mm Floor Space: 2,170W X 2,800D X 2,100H Mass Of Machine: 4,500Kg

Year of construction: 1998, condition: excellent (used), machine/vehicle number: ExCello Serial Number 3888, MICHIGAN Rotoflo Type 3237 Cold Forming Machine. Original Serial Number: 4590 ExCello Serial Number 3888 New 1975 rebuilt by ExCello late 1990’s Country of Origin: USA For the coldforming of profiles for serrations (straight or angular), spiral teeth, oil grooves, threads and knurls. Capacity: Hjdpfxofnk Eho Af Djpa Maximum slide stroke 1065 mm Maximum rack length 915 mm Maximum profile diameter 50 mm Maximum profile length 125 mm Standard module range 0.3 to 1.25 Motor size 15 kW Hydraulic tank capacity 1000 l Overall floorspace width of machine 5014 mm Width of machine 2768 mm Depth with outboard support 4165 mm Height 2000 mm Approximate weight of machine 11,700 kgs Complete with: Hydraulically operated outer support assembly to accommodate part length universal headstock, Universal rack holding feature.

Condition: used, GS Mach approx. 6.5" extruder with Water Ring Pelletizer, with Water Ring Pelletizer, spin dryer, screen changer, and hopper, includes all control panels, 177 HP, 3 phase motor, also includes Color Feeder, in working condition, winning bidder responsible for proper disconnection and removal. Hpedexd D Nnspfx Af Dea

Condition: good (used), Year of construction: 2002, LANDIS 3SE 14"x 60"ANGLEHEAD CNC GRINDER REBUILT BY LANDIS & TOOLED 2002 Equipped with: NEW FANUC CONTROL 2007 2-Axis Template Truform Servo Step Profile 30 Degree 30" Wheel Dead Headstock Table Traverse Marposs E39 Marposs Table Gauge Lateral Locator 3-Gauge TIR Gauge Steady Rests Wheel Balance Hpjdpfsrtr Easx Af Dsa Servo Motor-Traverse Stepping Motor Mist Collector Specifications: Swing: 14" Center Distance: 60" Motor: 1200 rpm Motor Pulley Diameter: 7.031" Spindle Pulley Diameter: 6.5" New Wheel Diameter: 30" Worn Wheel Diameter: 22" Max. Wheel: 8500 sfpm Max. Workhead: 333rpm X-Axis Ball Screw Pitch: 5mm per rev. X-Axis Total Stroke: 14.74" X-Axis Motor Pully Wheel Feed Diameter: 3" X-Axis Ball Screw Pulley Diameter: 3" Z-Axis Ball Screw Pitch: 10mm per rev. Z-Axis Total Stroke: 72.88" Z-Axis Motor Pulley Diameter: 3" Z-Axis Ball Screw Pulley Diameter: 6" Total Stroke: +/-2mm Total Marposs Voltage Output: =/-10vdc Dresser One Revolution of the Stepping Motor: .045" Diamond One Revolution of the Stepping Motor: .005" Weight: 25,000 lbs.

Condition: used, Polymer Recovery, Dremel Style plastic washer and spin dryer vibratory screener, gas blower system, sink float tank and feed hopper with augers, feed hopper will need to be removed from I-beam frame, unit is bolted and welded to frame (does not include lower I-beam frame), includes all control panels, winning bidder responsible for proper disconnection and removal of machine. Hpjdpfexd D I Rsx Af Dja

Condition: good (used), Year of construction: 2013, TOYODA (JTEKT) GL32M-63 CNC UNIVERSAL CYLINDRICAL GRINDER Equipped with: CBN Grinding Wheel Flagging Steady Rest Workhead Mounted Rotary Dresser Marposs P3SE System Monitoring Toyoda In Process Gaging Marposs E20N Acoustic Controller Air Gap Eliminator Workpiece Collision Control Coolant Pumps W/Magnetic Separator Pendant Control RH Workhead with Center LH Workhead with Center Work Rests Worklight Light Curtains Stacklight Extra Wheels Specifications: -Grind Center to Floor: 1,000 mm -Swing Over Table: 320 mm -Distance Between Centers: 630 mm -Grinding Diameter Range: 10 - 150 mm -Floor Space (Base machine w/auxiliary equipment): 3,400 x 5,000 mm -Net Machine Mass (approx.): 10,500 kg Grinding Wheel: -Type: CBN Wheel -Wheel Size (OD): 350 mm -Maximum Wheel Width: 60 mm -Surface Speed: 120 m/s Wheelhead: -Spindle Bearing: TOYODA STAT Bearing -Slide: V and Flat -Feed System: Ballscrew -Rapid Feed (on diameter): 30 m/min -Minimum Incsrement (on diameter): 0.0001 mm Workhead: -Type: Dead Spindle -Work Speed (Max): 500 rpm Hjdpfortrzpex Af Dopa -Center Taper: MT #4 Footstock: -Type: Hydraulic -Taper Compensation: Manual -Maximum Center Retraction: 60 mm -Center Taper: MT #4 Motors: -Wheel Drive Motor: 15 kW, Belt-Drive -Wheelhead Feed Servomotor: 1.3 kW Tank Capacities: -Wheel Spindle Lubrication Oil: 80 L -Hydraulic/Lubrication Oil: 20 L

Condition: used, Polystruder Extruder with Berringer water ring Pelletizer, 250 HP, 3 phase motor, with screen changer, includes spin dryer, and hopper. Hsdpfxoxd D I De Af Dspa

Condition: good (used), Year of construction: 2003, NAGEL MODEL TBT M320-6 6 SPINDLE CNC HORIZONTAL GUN DRILL, 2003 Equipped with: Panel Mate Power Pro Control Counter Rotation Cross Drilling High Pressure Coolant System Auto Loader Magnetic Chip Separator Hydraulic System Chiller Specifications: Maximum Drill Depth (Approx): 16" Maximum Drill Length: 36" Number of Drill Spindles: 6 Spindle Motors (3): 7.5HP HP Per Spindle: 3.75 Drill Head Slide Stroke: 16.9" Maximum Diameter Mild Steel: 0.750" Hjdpfxertrztj Af Depa

Condition: good (used), Year of construction: 2013, total length: 3,990 mm, total height: 2,500 mm, total width: 2,280 mm, overall weight: 8,500 kg, INGERSOLL CM SYSTEMS AOHD AGILE OIL HOLE DRILL Equipped with: Siemens 840D Control (2) Drill Heads 20-Tool Rack HSK 50A Taper (2) 7" 3-Jaw Chucks (2) Tailstocks (2) Steady Rests Chip Auger Chip Conveyor Mist Collector Hydraulic System Q R 2 Lube System Air Compressor Specifications: Hodpfxsrtrx Rj Af Depa Maximum Length: 1050 mm (41.3") Minimum Length: 180.0 mm (7.1") Maximum Stroke: 250.00 mm Maximum Main Journal Diameter: 115.0 mm (4.5") Maximum Pin Journal Diameter: 100.00 mm (3.9") Maximum Swing Diameter: 250.0 mm (9.84") X-Axis Travel: 1450 mm (57.1") Y-Axis Travel: 150 mm (5.9")W/HSK 50 Z-Axis Travel: 305.0 mm (12.0") A-Axis Travel: 360 Degree B-Axis Travel: 90 Degree Feed Rate (Z): 1 m/min Maxim (40"/min max) Position Accuracy of X,Y,Z Axes: .010 mm (.00039") Position Accuracy of A & B Axes: .03 Degree Position Repeatability of X,Y,Z Axes: .005 mm (.0002") Position Repeatability of A & B Axes: .005 Degree Spindle Power: 5.5 kW (7.5 hp) Spindle Speed: 0-6,900 RPM Tool Adaption: HSK 50E or A Tool Storage (ATC): 20 Total - 10 Per Spindle W/HSK 50 Lubrication - Slides & Ball Screws: Automatic Central Lubricator Approximate Floor Space (LxWxH): 4.0 x 2.3 x 2.5 m (13.1 x 7.5 x 8.2 Ft) Approximate Machine Weight: 8,500 kg (18,740 #)

Condition: good (used), Year of construction: 2011, LANDIS LT-2 TWIN WHEEL CNC ORBITAL CRANK GRINDER Equipped with: Landis 6400 CNC Control Siemens TOUCH HMI Arobetech Steady Rest Marposs P7 Gage System Lateral Locator Twin CBN Grinding Wheels Rotary Dresser Headstock Hpjdpfx Afsrtrxxj Dea Tailstock Rittal AC Units Specifications: Maximum Center Distance: 680 mm

Condition: good (used), Year of construction: 2015, machine/vehicle number: 190630, turning length: 150 mm, turning diameter: 200 mm, spindle bore: 42 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 50 rpm, travel distance X-axis: 150 mm, travel distance Z-axis: 155 mm, rapid traverse X-axis: 24 m/min, rapid traverse Z-axis: 24 m/min, turning diameter over bed slide: 220 mm, overall weight: 5,000 kg, spindle nose: 140 Flat, bar diameter (max.): 51 mm, power: 0.015 kW (0.02 HP), The innovative front-facing spindle of the 2SP-150H helps create an automation-friendly lathe for small parts production. By moving the spindle off the side and incorporating the Okuma Gantry Loader (OGL) into the production line, parts can be loaded and unloaded automatically. An extremely compact footprint improves floor space utilization, while the popular dual spindle option significantly reduces cycle time. Equipped with: Okuma OSP-P300L CNC Control 8" 3-Jaw Chuck Expanding Mandrel Hjdpfx Afjrtrlzs Djpa Turret Tooling Gantry Loader Pendant Controller Chip Auger Stack Light

Condition: used, Year of construction: 1973, machine/vehicle number: 24109, Equipped with: Stock Divider Hydraulic Work Clamping Hsdpfxsxdfa Us Af Depa Chip Conveyor Cutter Clamping Bolt Index Plate Change Gears Hydraulic System Coolant System Specifications: Min. Outside Cone Distance: 2.75" Max. Cone Distance: 10" Max. Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 6.8 to 16.5 RPM Feeds (seconds/tooth): 3 to 9 Main Motor: 5hp, 900 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approx. Floor Space: 118" x 86.5" Needed Overall Height: 70" Approx. Net Weight: 16,000 lbs Shipping Weight Boxed for Export: 17,000 lbs

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Index Plate Geneva Cam Hpedpfxoxdfazo Af Dea Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: used, Year of construction: 2011, machine/vehicle number: 25621, workpiece diameter (max.): 360 mm, Equipped with: Gear Spindle Runout: -Radial (Bore): .00005 -Axial (Face): .00005 Pinion Spindle Runout: -Radial (Bore): .00005 Axial (Face): .00005 Axis Repeatability: -X: .0001 -Y: .0001 -Z: .0001 Hedpfjxdfanex Af Depa Axis Lost Motion: -X: .00005 -Y: .00005 -Z: .00005 Fanuc 160I MB Control Base Work Holding Draw Bars Automatic Doors Spindle Chiller Transformer Hydraulic System Festo Pneumatics Automation Interface Available SPECIFICATIONS: Maximum Gear Outside Diameter: 360 mm (14.2") Maximum Pinion Outside Diameter: 340 mm (13.4") Maximum Pinion Drive Speed: 3000 rpm Maximum Gear Drive Speed: 1500 rpm Offset Vertical 150 mm ( 5.9") Pinion Cone Range: (90) (135-350) (70) (146-438)* (110) (51-343)* Gear Cone Range: (90) (65-280) (70) (78-306)* (110) (56-284)* Standard Testing Torque Load 2 to 90 Nm (1.5 to 66 ft-lb). Parallel Axis - face-to-face 147 - 362 - Center Distance -7 - 250 Pinion Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 419 mm (16.5") Gear Spindle Bore 39T - Diameter 99.2 mm (3.9") - Depth 250 mm (9.8") Floor Space (width & length) 2100 x 2550 mm (82.7 x 100.4") Height (to top of stack light) 2750 mm (108.3") Weight (base machine) 9100 Kg (20062 lbs)

Condition: good (used), overall weight: 10,364 kg, Year of construction: 2019, 2019 GENERAL BROACH 10-30 GBTU VERTICAL TABLE UP BROACH Equipped with: Retriever Shuttle Table Chip Conveyor Auto Load Grayco Lube AB Panelview Coolant Tank & Pump Specifications: Capacity: 10 Ton Stroke: 30" Table Up 1″ Puller / Retriever Hjdpjrtrzajfx Af Djpa Hydraulic Power Unit Chip Conveyor Machine Dimensions (approx.): 165″ x 48″ x 60″ Machine Weight Total (approx.): 22,800 lbs. Machine Column (approx.) : 13,000 lbs. Base w/ Chip Conveyor (approx.): 4,700 lbs. Electrical Panel (approx.): 600 lbs. Hydraulic Power Unit (approx.): 4,500 lbs.

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 Hsdpfxertrzds Af Dopa RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: good (used), gear diameter: 508 mm, total height: 1,780 mm, total length: 2,990 mm, total width: 2,200 mm, MODEL 610 GLEASON GEAR ROUGHER/FINISHER Equipped with: Hydraulic Workholding Pendant Control Chip Conveyor Index Plate Geneva Cam Change Gears Hydraulic System Coolant System Manuals Specifications: Maximum Gear Pitch Diameter: 20" Cutter Diameters: 9", 10.5", 12",14",16", 18" Whole Depth: 1.250" Root Angle: 60 to 80 deg. Face Width: 3.0" Extreme Ratio (Minimum): 2.25 to 1 Number of Teeth: 20 to 75 Diameter of Taper Hole at Large End: 3-27/64" Cutter Speeds (Per Minute) for Roughing: 15.6' to 87.7' Feeds (Seconds Per Tooth) for Roughing: 3 to 35 Cutter speeds (Per Minute) for Finishing: 6.8' to 20.5' Feeds (Seconds Per Tooth) for Finishing: 3 to 9 Hedpfx Aertrykjf Depa Floor Space: 118" x 86.5" x 70" H Weight: 17,500 lbs.

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: 32006, input voltage: 480 V, The Sprinter for Gears with Short Face Widths up to 100 mm The 100S Gear Shaping Machine is ideally suited for small face widths, for shaping spur and helical gears, internal and external, and for crowned and tapered gears. With only 6 m2 the 100S is one of the most compact machines of its class. Equipped with: Siemens Sinumerik 840D SL Control Hydraulic System 180 Degree Load System HSK-63 Spindle Auto Stroke Adjustment Chip Conveyor Chip Basket Flexlink Automation Festo Pneumatics Rittal Panel Conditioners Chiller 480/3/60, 35 KvA Motor & Controls Specifications: Workpiece With External Gear: -Largest Module (Steel W/Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Diameter: 100 mm Workpiece With Internal Gear: -Largest Module (Steel With Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Swing Diameter: 150 mm -Maximum Internal Diameter: 100 mm Tool: -Locating Cone In The Cutter Spindle: HSK-D63 Hpjdpertrvyjfx Af Dsa -Diameter Shaping Spindle: 85 mm -Maximum Stroke Length: 30 mm Machine Travel Distances: -Radial (X-Axis): 180 mm -Column Tilting (B-Axis): -1 - +11 Degrees Machine Workpiece Table: -External Diameter: 220 mm -Clamping Diameter: 160 mm -Bore: 63 mm Speeds: -Feed Rate X-Axis: 12,000 mm/min -Workpiece Table (C-Axis): 0-400 min-1 -Cutter (C2-Axis): 0-300 min-1 -Spindle Stroke (A-Axis): 500-3,000 min-1 Electrical Equipment: -Operating Voltage: 480V -Supply Voltage: 115V -Control Voltage: 24V -Frequency: 60 Hz -Connected Load of Machine: 35 kVA -Cable Cross-Sectional Area: 35 mm2 -Protection: 80 A Machine Overall Dimensions (L x W x H): 3,380 x 3,950 x 3,015 mm Weight of Machine: 7,800 kg

Condition: used, Year of construction: 1996, functionality: fully functional, machine/vehicle number: 25734, Equipped with: Fanuc 150MB Control Hydraulic Chucking Work Spindle Large Bore Work Spindle #80 Taper Stock Divider Helical Motion Modified Roll Hansen Coolant Chiller & Filtration Coolant Tank & Pumps Chip Conveyor Chip Hopper Reven Mist Collector Hydraulic System Transformer Cutter Bolt Work Light Hedpfsxaqa Sjx Af Djpa Operator Platform Hand Tools Documentation Specifications: Extreme Ratio: Face Milling: 10:1, Face Hobbing: 10:1 Full Depth: Maximum: Face Milling:1.25" (31.75mm), Face Hobbing: 0.93" (23.50mm) Face Width: Maximum: Face Milling:6.00" (152.00mm),Face Hobbing: 3.00" (76.20mm) Range of Tooth Numbers: 1-300 Inclusive Gear Pitch Diameter, Maximum: 1000 mm (39.37") Cutter Size, Maximum: 18" (diameter) Face Milling Cutter Size, Maximum: 350 mm (radius) Face Hobbing Root Angle Range (B-Axis) 5 deg.to 90 deg., Face Hobbing:5 deg. to 90 deg. Machine Center to Work Spindle Face:9.00"Fixed, 229mm (Fixed) A-Work Spindle: 0 to 67 RPM, 0 to 333 RPM B-Swinging Base: 0 to 30 deg./sec, N/A C-Cutter: 0 to 500 deg., Same X-Horizontal: +/-305mm (+/-12") Y-Vertical: +/-305 mm (+/-12") Z-Sliding Base: -25/+700mm (-1/+28") B-Root Angle: -5 Degree/+90 Degree Diameter of Taper Hole at Large End: 8" (#80 Taper) to 6" (#60 Taper) Taper Per Foot:3/4", Same Depth of Taper Front:6", 152.40 mm Depth of Bore: 678 mm (26.7") Diameter of Taper Bore: 140 mm (5.5") Diameter Through Spindle of Hole:7.125", 180.98 mm MACHINE DIMENSIONS: Length x Width:233"x 209", 5920 mm x 5310 mm Height: 129", 3280 mm Weight: 65,000 lbs., 29,484 kg