Condition: excellent (used), Edgebander Artech Akron 435 Pre-milling, Glue application by roller, Pneumatic pre-cut guillotine, Pressure rollers, Finish trimming saws, Multi-cutter R1-R2 – top and bottom milling and corner processing, pneumatic adjustment, Profile scraper, Flat scraper, Polishing unit, Max. workpiece height: 60 mm Max. edge thickness in roll: 3 mm, Nedpfoy Dtw Dox Akqscr Feed speed: 12 m/min Condition: very good.

Condition: reconditioned (used), Edging thickness: strip material up to 8 mm, roll material up to 3 mm Jointing unit Glue application (cartridge system glue nozzle) Pressure unit Cut-off station Milling station Pull scraper Corner copying Surface scraper Nodpfx Akoy Diwmeqecr Total length approx. 5350 mm (including magazine table) Overhaul: Motorized infeed fence Heating system completely overhauled, new heating element with coating Heating system modification for automatic refilling Conversion to sensing nozzle Milling: conversion to motorized adjustment New knives Detailed equipment on request Data taken from a data sheet, therefore no guarantee

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging Njdpfxsy A I Sgj Akqscr - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: used, BRANDT Optimat KDF340 Edge Bander Pre-milling cutters Adhesive application by roller Pneumatic pre-cut guillotine Pressure rollers End-cutting saws Ncodpfxjy Dc Ule Akqsr Top-bottom milling unit R1-R2 Profile scraper Polishing unit Max. workpiece height: 45 mm Max. edge thickness from roll: 3 mm Feed speed: 10 m/min Machine length: 350 cm Machine inspected, ready for operation

Condition: like new (used), Hebrock F4 Edge Bander Well-equipped, available for inspection before purchase. Note: The machine can be viewed and tested from May 11th. Pre-milling cutters, Glue application via roller, Equipped with glue drain, The glue pot is replaceable. Pneumatic pre-cut guillotine, Pressure rollers, Flush trim saw, Top and bottom milling unit, R1–R2, Profile scraper R1-R2, Interchangeable corner rounding unit for 1mm and 2mm, Flat scraper, Nesting capability, Ncjdjy Dcmuopfx Akqor Pneumatic 3-point adjustment, LED lighting, Max edge tape thickness (in roll): 3mm, Feed speed: 7 and 10 m/min, Power requirement: 7.08 kW, Machine as new, ex-demo.

Condition: ready for operation (used), Year of construction: 2008, Edgebander manufactured in 2008. This BIESSE Edge Stream B1 features a comprehensive set of tools including a PU-gluing machine, pre-milling unit, edge trimmer, and fine milling unit. It also includes rounding and edge scraper units, along with swaying brushes and an edge heater. If you are looking to get high-quality edging capabilities, consider the BIESSE Edge Stream B1 machine we have for sale. Contact us for further details. • Liquid spray unit (ADZ) • Pre-milling unit (RT) • PU gluing unit (SP10, Nordson) • Edge trimmer (IT90) • Balance tool trimmer (RS10) • Fine milling unit (RF40) • Rounding unit (AR60) • Edge scraper (RB40) • Glue scraper unit (RC20) • Swaying brushes Nodpfx Aeyw Nu Eokqjcr • Edge heater (PH10)

Condition: used, Year of construction: 1981, Special milling machine used, in good condition Brand: Stegherr Type: F3 Year of manufacture: 1981 Machine no.: 7 / 10802 Motor: 3.2 kW Number of spindles: 2 pcs Nedpoy Ay A Dsfx Akqocr Solid edging max. 48 mm Workpiece height min. 10–60 mm x 30 mm width Milling heads with reversible inserts: 2 pcs Tool diameter: 100 mm Tool width: 50 mm Bore: 30 mm Feed unit: 0.25 Variable feed speed Weight approx. 350 kg Storage location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery in as-inspected condition, without warranty or guarantee

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment and technical data: - Control unit with 15" touch screen - Jointing milling unit with 2 milling heads - Edge feed - GluJet 301 glue application system: 2.3 kW, automatic glue height adjustment, sensor nozzle - Pressure unit: pneumatic - End trimming unit: pneumatic - Diamond cutters left/right with CM technology - Corner copying unit with diamond cutters Nodpfx Aoyxyahskqjcr - Surface scraper - Polishing unit - Extendable workpiece support - Motorized pressure bridge adjustment with NC axis via program control - Extraction hoods for end trimming unit - Multifunction milling unit: MOT 4 - Vertical tracing rollers: pneumatic - Pneumatic tilting device for milling unit MOT 4 - Scraper unit MOT 2 with chip collection box - Spray unit for infeed and outfeed area - Minimum workpiece length: 160 mm - Workpiece thickness: 6-60 mm - Edge thickness: 0.4-6 mm - Feed speed: 10 m/min - Total length: 4930 mm - Weight: 1420 kg Availability: short-term Location: 63934 Röllbach

Condition: used, machine/vehicle number: 008430, Position 1: Panel Feeding and Loading MAHROS + STEFANI-RUNNER + EVOLUTION Position 2: Double Sided Squaring/Edgebanding Machines MAHROS + STEFANI-RUNNER + EVOLUTION Ncedpfx Aeyqxx Sekqjr Position 3: Panel Stacking and Offloading MAHROS + STEFANI-RUNNER + EVOLUTION

Condition: used, OTT Tornado - TOP Control via a 15-inch color touch monitor for full automation and maximum operating convenience CM-CombiMelt gluing system suitable for processing both EVA and PUR hot-melt adhesive as well as all standard cleaning granulates Joining unit for bonding chipboard panels Automatic roll magazine Automatic edge magazine Double end trimming unit with automatic swiveling 0° / 3° Ncodpfeyym Dcox Akqer Flush trimming unit - for flush trimming - 12mm Fine radius trimming unit - radius trimming - profile cutters R2 - R5 Automated copy milling - corner rounding Scraper unit - radius - chamfer Flat scraper unit Release agent spraying device - PU Cleaning set with fine polishing unit Very stable workpiece support with roller conveyors - FRONT with scissor extension Complete set of tools included Machine is in EXTREMELY WELL-MAINTAINED CONDITION Machine from a joinery workshop Available from stock in Lieboch

Condition: used, Holz Her Auriga 1308 FÜ + PU Compact design – edge thickness 0.4 – 6 mm SPS touchscreen control Edge-Control PPC 221 color screen Ncsdoyyl U Hepfx Akqor Pre-milling unit for preparing prior to adhesive application Fully automatic edge magazine for coil and strip material Glue application station GLU-JET, EVA and PUR adhesive (cartridge or granulate) + PU Glue application via nozzle technology Workpiece height 6–65 mm Automatic glue height adjustment Pressure unit 1912-3, pneumatic End trim unit 1918, pneumatic, for coil and strip material up to 8 mm edge thickness With pneumatic adjustment for trim saw angle 0–10° Milling unit 1827 MOT 4, flush milling 8 mm, radius milling – chamfer milling – 15°, 1827 MOT NC axes via control panel Corner rounding unit 1832 SPS, corner rounding for edges up to 3 mm thickness in through-feed operation Scraper unit for chamfers and radii with 2 scraper holders (motorized) Surface scraper unit – finish Spray unit – PU Complete set of DIA tools included Few operating hours / from a craftsman's workshop Machine is FACTORY OVERHAULED and in TOP CONDITION Available ex stock Lieboch

Condition: good (used), Year of construction: 2008, machine/vehicle number: 0-260-20-1170, Kantfräs & kap Brandt Type: Optimat FTK 130 No: 0-260-20-1170 Year: 2008 The FTK 130 has been conceived as complementary to edge banding machines. The main application of the FTK 130 is shaped workpieces, where internal as well as external radie can be processed. Also straight workpieces can be easily processed. Shaped workpiece trimming technology For small shops the FTK 130 is offering a flexible and cost effectiv solution for their trimming requirements. In order to process internal and external shapes, the trimming motors are mountedvertically. Milling and cutting units for simultaneous upper and lower radius/clean milling of excess edging material on workpieces with straight edges and on rounded workpieces with internal and outside radie. Cutting unit to precisely cut excess front and back edge trim material. in the longitudinal direction of the working pressure. Techn info: Milling unit Workpiece thickness approx. 12-55mm Workpiece width min approx. 30mm Ncodsq Ehpaepfx Akqor Inner radius min.ca.35mm Edging thickness max. approx. 3mm Milling tool 2xWPL radius cutter r=3, diameter 67x21x16mm Milling motors 11000v/min Cutting unit Workpiece thickness 12-55mm The thickness of the edging material max. 3mm Saw blade diameter 100mm Sawing width 3mm Center hole 36mm Compressed air 6 bar, connection 1/2", approx. 2000PA Air consumption per stroke approx. 10NL Extraction power diameter 80mm, 510m3/h, air speed 28m/sec Current 400 volts, 2.5kw 50 hz, 3 phase, 16A Dimensions: 1130x765x1480mm (lxwxh) Weight 320 Kg Stock no: 2001877BXA

Condition: used, machine/vehicle number: 007840, Type of edging: Thin edge, Thick edge Gluing System: PUR Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 30 m/min Ncedpfjyg Eg Ijx Akqsr Maximum panel thickness: 60 mm Operating Units: 8 nr

Condition: used, Storage location: Sonnefeld Ncedoway Dcepfx Akqor

Condition: used, Year of construction: 1996, Edge thickness: 0.4 - 12 mm Roll edge: 3 x 45 mm or 0.8 - 60 mm Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Workpiece thickness: 10 - 55 mm Feed rate: 13 m/min Pre-milling (joining) Glue pot Quickmelt Gluing unit Trimming Flush trimming Chamfering Radius trimming Corner rounding Flat scraper Buffing unit Machine dimensions: 7450 x 1220 x 2400 mm Weight: 3000 kg Storage location: Nattheim Nedpsvvkd Tofx Akqocr

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Ncedpfsvvkfdox Akqer

Condition: used, Year of construction: 2001, Edge thickness 0.2 - 6 mm Workpiece dimensions Width min. 70 mm Height min. / max. 8 / 42 mm Length min. 150 mm (strip edges) Feed speed: 12 m/min Glue application roller Machine dimensions L x W x H = 3500 x 900 - 1300 x 1250 mm Weight: approx. 1130 kg Power consumption: approx. 6.0 kW, 400 V, 50 Hz Equipment: - Double top pressure with manual height adjustment - Automatic magazine for roll edges up to 800 mm DM - Rapid heating tank with application roller in synchronous and counter-rotating direction - Pneumatic adjustment and resetting of all work units - Pneumatic cross-cutting shears for strip edges up to 3 mm - Manually adjustable infeed ruler - Double cross-cut saw 2 HF motors 0.2 kW, 12,000 n 2 automatic Positions = 0 + 3 degrees - Milling/flush trimming unit with two HF motors 0.43 kW, 12,000 n. Two-sided scanning with two HF indexable cutter heads. Radius scraper, automatically controlled. Flat scraper, automatically controlled. Nedpjvvkfqsfx Akqjcr Storage location: Nattheim

Condition: used, Year of construction: 2002, Machine length: 6240 mm Weight: 2400 kg Power consumption: 14 kW Extraction diameter: 120 / 140 mm Storage location: Nattheim Ncjdpfx Akevvkfwjqsr

Condition: used, Year of construction: 2011, Pneumatic milling adjustment (Straight/Radius) Combination milling station R=2 Corner rounding cutter R=2 to 40 mm Jointing cutter up to 40 mm Flat scraper Profile scraper R=2 Short workpieces PLC control with Pro Face touchscreen Nesting Cooling/antistatic spray - airtronic Protective spraying Kante Riepe incl. interchangeable tank Workpiece thickness 8 - 60 mm Mechanical edge clamping Extraction nozzle: 140 mm Dimensions: Length with extension: 4984 mm Depth with roller table: 1425 mm Max. height: 1618 mm Worktable height: 888 mm Weight: 1400 kg Nsdpfjxyiilsx Akqecr Storage location: Nattheim

Condition: used, Year of construction: 2006, EVA glueing, 2 pressure rollers, cross-cutting station, pre-milling cutter and rounding cutter, surface scraper, transport device Storage location: Nattheim Ncjdpfx Aevvkg Iskqor

Condition: used, Year of construction: 1999, Edge height: 10 - 60 mm Edge thickness: 0.4 - 3 mm Min. curve radius: 20 mm Feed speed: 2 - 18 / 4 - 14 m/min. Motor: 5.2 kW Air pressure: 6 bar Dimensions: 900 x 1300 x 1200 mm Weight: approx. 350 kg Storage location: Nattheim Njdpfx Ajymcrbjkqjcr

Year of construction: 1990, condition: used, edge heights: 10 - 60 mm edge band material thickness: 0,4 - 25 mm electr. connection: 380 V, approx. 9,9 kW Ncjdpfxo T T Ddo Akqjr space needed: 2900 x 870 x 1320 mm weight: 780 kg

Condition: not inspected (used), Year of construction: 2016, functionality: unexamined, edge thickness (max.): 22 mm, rotational speed (max.): 12,000 rpm, Equipment: CE marking, The machine has the following configuration: Pre-milling unit Nodsyxndbopfx Akqocr Automatic, timer-controlled intervention and positioning via NC Edge preheating lamps Edge band magazine Glue pot for EVA hot-melt adhesive Premelter for EVA hot-melt adhesive QM-705 End trimming unit IN-801 Number of motors: 2 Top and bottom flush trimming unit RS-100 Number of motors: 2 Motor power: 2 kW Speed: 12,000 rpm Fine finishing and contour trimming unit RF-100 Number of motors: 2 Motor power: 2 kW Speed: 12,000 rpm Corner rounding unit AR30 Number of motors: 2 Motor power: 0.8 kW Speed: 12,000 rpm Automatic, timer-controlled intervention End cutting unit RB02 Positioning by NC Glue scraping unit RCC-701 Polishing unit SP-501 Number of motors: 2 Motor power: 0.25 kW Spraying unit LPT-700 TECHNICAL DETAILS Panel height min: 10 mm Panel height max.: 60 mm Edge thickness min.: 0.4 mm Edge thickness max.: 22 mm MACHINE DETAILS Total connected load: 22 kW EQUIPMENT Feed pressure with rubber belt Panel support guides with NC positioning CE marking The machine is sold and delivered as is (“as seen and approved”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the place of destination. External reference: 7673

Condition: good (used), Year of construction: 2014, machine/vehicle number: 0-200-01-2196, functionality: fully functional, input current: 63 A, height adjustment type: electric, feed rate X-axis: 25 m/min, actuation type: electric, total height: 2,000 mm, total length: 7,850 mm, total width: 2,300 mm, overall weight: 5,000 kg, Equipment: CE marking, documentation/manual, Edge banding machine, good working condition, fully electric adjustments, working speed 25m/min, available immediately. Nsdpfxjy Ebl Se Akqjcr

Year of construction: 2001, condition: used, functionality: unexamined, Edgebander for mouldings using hot stamping method MAKOR type DORA 7, year of manufacture 2001 Nedpoytc E Uofx Akqecr