Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm Csdpfx Asvivmyjh Ueri >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: like new (used), Year of construction: 2015, operating hours: 15,000 h, functionality: fully functional, Year of manufacture: 10-2015 Control: OSP P300S Maximum turning diameter: 650 mm Main spindle Drive power: 32/22 kW Max. spindle speed: 3,000 rpm Max. torque: 955 Nm Spindle nose: A2-11 Spindle bore: 112 mm Hollow clamping cylinder SMW-VNK225-95, bore 95 mm Sub spindle Drive power: 26/22 kW Max. spindle speed: 4,000 rpm Max. torque: 420 Nm Spindle nose: A2-8 Bearing inner diameter: 80 mm Solid clamping cylinder SMW SIN-S175 Milling spindle Drive power: 22/18.5 kW Max. spindle speed: 12,000 rpm B-axis: 0.001° HSK-A63 Travel paths X1/X2-axis: 695/235 mm Y-axis: 300 mm Z1/Z2-axis: 1,600/1,524 mm B-axis: -30° to +210° Tool magazine / ATC 80 tool positions Codpfsxu Awlex Ah Ueri Max. tool diameter: 90/130 mm Max. tool length: 400 mm Lower turret 12-position tool turret Turning tool: 25 mm Boring bar: 40 mm Special equipment Software for limiting spindle speed to 3,500 rpm Software for multifunctional tools Software extension kit One Touch IGF-M-D Machining Navi M-g for milling operations Tool breakage detection – Renishaw TRS2 laser Machine-side preparation for high-pressure coolant 70 bar Factory-installed door automation Robot interface (Type “E”) Connection for oil mist extraction Separate coolant filtration system TMF300/980, drum-type swarf filter, clean tank 980L Chip conveyor Standard equipment Lower turret with 12 stations, direct mounting system "radial", with cylindrical roller guide on ZB-axis, sliding guide on XB-axis Collision avoidance system (CAS) in real time 19'' color LCD TFT with 3D color graphics as touch screen Second operating system Windows 7 for operation and open data communication, freely usable for Windows 7 compatible applications Tool monitoring system for service life and breakage+ Tool measuring device Machine management MacMan with integrated BDE Ethernet interface with browser and DNC-T1 for program transmission Prepared for remote diagnostics Harmonic spindle speed oscillation by periodic speed variation Tool height correction in Y-axis for rotating tools Circular thread milling X/Z/Y/B including eccentric milling X/Y/C Hi-Cut Pro high-speed control for rotary tools Coordinate transformation Electronic spindle orientation Dimensions and weight L/W/H: 4,480/3,082/3,030 mm, Weight: 18,000 kg

Condition: ready for operation (used), Year of construction: 2022, operating hours: 113 h, functionality: fully functional, machine/vehicle number: AL150210302, turning length: 336 mm, turning diameter: 440 mm, spindle bore: 61 mm, spindle speed (max.): 6,000 rpm, controller model: DMG MORI COMPACT LINE, No minimum price – guaranteed sale to the highest bidder! Only 113 operating hours! Payment deadline for the machine is 04.12.2025! Bidding obligates you to collect the machine on time between 10.12.2025 and 12.12.2025! TECHNICAL DETAILS Turning length: 336 mm Turning diameter: 440 mm Bar capacity (max.): 52 mm Swing over bed: 620 mm Swing over cross slide: 465 mm Spindle speed (max.): 6,000 rpm Number of spindle speed ranges: 1 step Spindle bore diameter: 61 mm Spindle bearing inner diameter: 100 mm Square tool shank diameter: 20 mm Boring bar shank diameter: 32 mm Cedsxvbwajpfx Ah Ueri X-axis travel: 260 mm Z-axis travel: 375 mm Rapid traverse in X-axis: 30,000 mm/min Rapid traverse in Z-axis: 30,000 mm/min Number of tool magazine stations: 12 MACHINE DETAILS Control model: DMG MORI COMPACT LINE Frequency: 50 Hz Operating hours: 113 h EQUIPMENT Coolant system Chip conveyor

Condition: excellent (used), Year of construction: 2018, MAZAK QUICK TURN 250MY 500U Max. turning diameter: 380 mm Max. turning length: 504 mm Max. milling speed: 5,000 rpm Max. spindle speed: 4,000 rpm Max. bar diameter: 80 mm Credpfx Ahew Rqqyo Usi The machine is equipped with: - CNC control Mazatrol SmoothG - KITAGAWA three-jaw chuck BB-210, diameter 254 mm - Tool Eye - C-axis - Y-axis - NC tailstock - Reinforced coolant pump - Chip conveyor - 8 pcs. fixed tool holders - 2 pcs. driven tool holders

Condition: ready for operation (used), Year of construction: 2007, General Data Measurements width 2050 Measurements depth 2695 mm Measurements height 2120 mm Machine weight 5800 kg Main Drive Spindle speed range 5000 / Sub-spindle: 6000 rpm Spindle motor power 15/15/11 kW Sub-spindle: 11/7.5 kW Spindle bore 73 mm / Sub-spindle: 43 mm Number of axis 4 Movement X-Axis Movement 260 mm X-Axis Rapid Traverse 30000 mm/min Y-Axis Movement 100 (±50 mm) Y-Axis Rapid Traverse 10000 mm/min Crodpfx Ahsxuw Eqs Uji Z-Axis Movement 590 mm Z-Axis Rapid Traverse 30000 mm/min B-Axis Movement 564 mm B-Axis Rapid Traverse 400 min⁻¹ Workpiece Workpiece drm over bed 923.8 mm (579.8 mm with front cover) Workpiece drm over support 755 mm Workpiece drm 356 mm Additional Equipment Gantry loader for automatic loading and unloading This 4-axis MORI SEIKI NL 2000 SY /500 turn-mill centre was manufactured in 2007. Ideal for precision machining, it features a robust design and advanced control system. If you are looking to get high quality turning and milling capabilities consider the MORI SEIKI NL 2000 SY /500 machine we have for sale. Contact us for more information. Application Types Turning

Condition: used, Year of construction: 2013, functionality: fully functional, HWACHEON - Cutex 160 B Offer Details Stock Number: 1039-9338 Machine Type: CNC Lathe Manufacturer: HWACHEON Model: Cutex 160 B Year of Manufacture: 2013 Control System: Fanuc Oi-TD Location: D-59302 Oelde Country of Origin: Korea Delivery Time: by arrangement Csdext N I Ispfx Ah Ueri Freight Terms: ex location Additional Information: CNC Lathe HWACHEON - Cutex 160 B Operating Hours: - Control on: approx. 26,932 h - Machining time: approx. 7,546 h WE OFFER YOU: - Workshop-inspected machines - Free loaded on truck - NO auction fee - Delivery possible (at extra cost) - Unloading and commissioning (at extra cost) Technical Details Turning diameter max.: 300 mm Turning length max.: 284 mm Control: Fanuc Oi-TD Swing diameter over bed: 550 mm Chuck diameter: 210 mm Spindle nose: A2-6 Main Spindle: Max. speed: 4,500 rpm Spindle bore: 62 mm Bar capacity: 51 mm Spindle bearing diameter: 100 mm Main spindle drive power: 11 / 7.5 kW Travel: X-axis travel: 170 mm Z-axis travel: 335 mm Tool Turret: Number of tool stations: 12 positions Tool size: Ø25 x Ø40 mm Feed Rates: Rapid traverse (X / Z): 36 / 36 m/min Tailstock: Quill diameter: 60 mm Quill stroke: 80 mm Tailstock taper: MT 4 Total power requirement: 25 kVA Machine weight approx.: 3.2 t Space requirement approx.: 8.5 x 2.5 x 2.0 m Accessories - Documentation - Chip conveyor - Coolant system - Tailstock - Signal lamp - Parts catcher - Hydraulic unit - 3-jaw chuck: SEOAM CAH-08 - Collet chuck: HAINBUCH nova size 65 - Tool measurement - Interface for bar feeder - Bar loading magazine: Breuning SIMAG 70.1-3000 - Various toolholders

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake Cedpfx Ahjxcuazs Ueri About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: excellent (used), Cycle Lathe Weiler E 50 / 1D Year of manufacture: 1999 Machine no.: 684 Control: Weiler (Siemens 810D) Power-on hours: 43,543h (Machine was overhauled by Schmeißer a few years ago) Technical specifications: Spindle speed: 1–625 / 4–2,500 rpm (2 gear stages) Drive power: 17kW torque Crjdpfx Ahowtqnrj Uoi Spindle torque: 1,200Nm Spindle bore: 66mm Distance between centers: 1,000mm Center height: 280mm Swing diameter over bed: 570mm Swing diameter over cross slide: 340mm Equipment/Accessories: - Interface for external programming - Parat tool holder incl. 6 holders - Operating manual - Coolant system - Various turning tools and drills - Jaws for lathe chuck - Live center - Machine feet The machine has been tested under power and is in perfect, ready-to-use condition. The machine bed is also in good condition. Price: net ex works, loaded on truck from stock.

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 286964, travel distance X-axis: 200 mm, travel distance Z-axis: 300 mm, overall weight: 5,000 kg, controller model: MAZATROL SMOOTH C, Equipment: chip conveyor, The payment deadline for the machine is 04/12/2025! Placing a bid obliges the buyer to collect the machine within the specified period from 10/12/2025 to 12/12/2025! TECHNICAL DETAILS Travel X-axis: 200 mm Travel Z-axis: 300 mm Control: MAZATROL SMOOTH C MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 4,000 x 2,500 x 2,000 mm Total weight: 5,000 kg Electrical Data Operating voltage: 400 V Frequency: 50-60 Hz Rated current: 46 A Connection load: 26.1 kVA Codpfx Aoxvbdgoh Ueri EQUIPMENT 12-position tool turret Three-jaw chuck (diameter: 160 mm) Sorting unit with vibrating head by GRIMM Chip conveyor Cooling system

Condition: excellent (used), Year of construction: 2004, MAZAK QUICK TURN NEXUS 200MS-Y Max. machining diameter: 380 mm Csdpfx Aew Du S Ash Usri Max. machining length: 511 mm Max. milling speed: 4,500 rpm Max. spindle speed: 5,000 rpm Max. bar diameter: 65 mm Machine is equipped with: - CNC control Mazatrol 640T Nexus - KITAGAWA three-jaw chuck BB-208 for main spindle, diameter 210 mm - KITAGAWA three-jaw chuck B-206 for 2nd spindle, diameter 169 mm - Tool Eye - C-axis - Y-axis - Interface for bar feeder - Automatic parts catcher - Reinforced coolant pump - Chip conveyor - 8 fixed tool holders - 2 driven tool holders

Year of construction: 2014, operating hours: 2,041 h, condition: ready for operation (used), Main Drive Spindle speed range 56-2800 Tool taper ISO 50 Number of axis 2 Crjdpfexf N Sdox Ah Uji Control Unit Brand SIEMENS Model SIEMENS 828D Additional Equipment Console: Automatic cycle in the longitudinal direction with activation of console recess. This Romi C 510 was manufactured in 2014. It features a milling spindle with ISO 50 taper, automatic tool clamping, and hardened guide surfaces. The machine operates with a standard spindle speed range of 56-2800 and includes automatic lubrication and cycle functions for efficient operation. If you are looking to get high-quality turning capabilities, consider the Romi C 510 machine we have for sale. Contact us for more information. Application Types Turning

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard Crjdpfjw Idllox Ah Usi About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: excellent (used), Year of construction: 2004, We are offering an exceptionally high-quality precision lathe. Within its class, this is likely the best German lathe ever built. BOEHRINGER Precision Lathe Model DUE 500 Year of manufacture: 2004, including CE certification and central lubrication Machine No.: T1022.2027-00 Center height: 240 mm Swing diameter over bed: 500 mm Swing diameter over cross slide: 285 mm Center distance: approx. 1,200 mm Effective turning length: approx. 1,000 mm Bar capacity: 62 mm Spindle nose: DIN 55027 Size 6 Spindle bore: 100 mm Drive power: 11 kW Maximum torque: 2,000 Nm Csdpow Rdthefx Ah Usri 24 spindle speeds: 11.2 – 2,240 rpm 60 cross feeds: 0.03 – 28 mm/rev 60 longitudinal feeds: 0.06 – 56 mm/rev Tailstock quill stroke: 190 mm Tailstock taper: MK 5 Machine footprint (LxW): approx. 4,000 x 1,525 mm Weight: approx. 4,300 kg Accessories: - HEIDENHAIN 3-axis digital readout - Central lubrication system - Electrically interlocked chuck guard - Coolant system - Chip protection rear panel - Röhm chuck, T 250 mm, with various jaws - Telescopic cover for lead and feed screw, support to bed - Machine lamp - Multifix C + 4 quick-change tool holders - Live center - Operating manual - Circuit diagram - Rapid traverse in longitudinal and cross slides Condition: The machine is in very good technical and visual condition. Backlash on cross slide approx. 0.3 mm, on compound slide approx. 0.15 mm Spindle nose runout approx. 0.006 mm Bed geometry: deviation approx. 0.01 mm over approx. 750 mm bed length (measured on flat guideway towards chuck using dial indicator) The following parts have been renewed: - Oil change - New hoses for central lubrication - New wipers - Key for operating lever replaced - Locking pin for interlock replaced Price is net, ex stock, loaded free of charge. Delivery by company truck can be arranged at extra cost.

Year of construction: 2008, condition: ready for operation (used), General Data Measurements width 2200 mm Measurements depth 5000 mm Measurements height 2340 mm Machine weight 11700 kg Main Drive Spindle speed range 3500 Number of axis 5 Movement X-Axis Movement 255 mm Y-Axis Movement 100 mm Z-Axis Movement 800 mm Table Crjdpfxjxuwz So Ah Uei Number of tslots 2x12 This 6-axis DOOSAN Puma TT 2500 SY was manufactured in 2008. It features a max turn diameter of 390mm, bar passage of 76mm, and a max working length of 700mm. Spindle speeds reach up to 3500 RPM with live tools at 4000 RPM. Ideal for complex turning tasks. Contact us for more information about this machine. Application Types Turning

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm Crsdowrmuxopfx Ah Uei >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: good (used), Lead and feed spindle lathe Matra SM-3000 Country of origin: Spain Turning diameter over bed 600 mm Turning diameter over support 370 mm Turning length 3000 mm Turning diameter in the crank 900 mm Length of the crank 280 mm Spindle bore 72 mm Cjdpfjvq I Npex Ah Uori Speed range 17-1,652 rpm Spindle speed levels 36 Main motor, power 9/11 kW Rapid traverse longitudinal-transverse Tailstock MK5 Machine weight approx. 4 t Dimensions (LxW) approx. 4800x1300mm Equipment/accessories: - Fixed steady rest with rollers/max. Workpiece diameter 220 mm - Coolant system - Bed stop - Röhm lathe chuck D500mm - Digital display 2-axis SINO - Multifix C base holder The machine is in very good, fully operational condition. Price net, free loading from warehouse

Condition: ready for operation (used), Year of construction: 2004, General Data Measurements width 2050 mm Measurements depth 3100 mm Measurements height 2120 mm Machine weight 6200 kg Main Drive Number of axis 4 Movement Codpfx Ahoxuw Eko Ueri X-Axis Movement 260 mm Y-Axis Movement 100 (±50 mm) Z-Axis Movement 795 mm Additional Equipment Counter-spindle: Yes / Y-axis: Yes / Driven tools: Yes/ Bar loader: Yes Number of tool stations: 12 (10) / Shank height for square tool: 25 mm / Boring bar tool shank: Main Spindle: Max. 50 mm / Sub-spindle Max. 32 mm / Boring bar tool shank: Main Spindle: Max. 50 mm / Sub-spindle Max. 32 mmz / Turret switching time: 0.25 s / Max. speed of driven tools: 6000 rpm Rapid traverse speed: X/Z-axis: 30000 mm/min / Y-axis: 10000 mm/min / C-axis: 400 min⁻¹ This 4-axis MORI SEIKI NL 2500 SY/700 turn-mill centre was manufactured in 2004. Ideal for precision machining, it features a robust design and advanced control system. Consider the opportunity to buy this MORI SEIKI NL 2500 SY/700 turn-mill centre. Contact us for more information. Application Types Turning

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Weiler Center Lathe Model Condor B Guide & Feed Shaft Lathe with 3-Axis Digital Readout by K&C NEW from Training Workshop!! Technical Data: >> Machine No. 91-1814, Year of manufacture: 1991 >> Center height: 165 mm >> Distance between centers: 750 mm >> Spindle speeds: from 22 to 2,800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet locking >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Threads possible: Metric, Imperial, Module, and Diametral Pitch >> Metric thread leads: from 0.18 to 28 mm >> Weight: approx. 1,100 kg >> Spindle brake switchable >> Dimensions (L x H x D): 1.83 m x 1.29 m x 0.88 m Scope of Delivery and Features: >> NEW 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating manual Functions: mm/inch switch, ABS/INC coordinate selection, display value halving, reference mark, tool programming for 200 items, taper calculation, radius/diameter display, quick zeroing, counting direction reversal >> 1 pc. NEW 160 mm 3-jaw chuck, 2 sets of jaws >> 1 pc. 160 mm 4-jaw chuck, 1 set of jaws >> NEW collet chuck and NEW collets from 2 to 24 mm, incremented by 1 mm >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle safety guard >> Rear splash guard >> Fixed steady rest >> Machine feet Safety features: electronic spindle guard, 2 emergency stop switches, change gear cover with limit switch, spindle brake About the machine: Crjdpfx Aow Nw Dqsh Uoi We are offering a Weiler Condor in very good condition. The machine is, of course, fully operational. It is a very robust and powerful lathe. The brand new 3-axis digital readout from K&C makes operation even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine under power at our premises.

Condition: reconditioned (used), We are offering an exceptionally good precision lathe. The machine is probably the best German lathe that has been built in this class. BOEHRINGER precision lathe model DUE 800 Year of manufacture: 1984 Order no.: 04041.01-807 Center height: 400 mm Circulation diameter over bed: 820 mm Circulation diameter over facing slide: 515 mm Center width: approx. 2200 mm Effective turning length: approx. 2000 mm Cedpfx Ahert T S Re Uori Bar passage: 128 mm Spindle head DIN55022 size 11 Drive power: 30 kW Max. Torque: 6300 Nm 24 Speeds: 7.1 - 1400 rpm 60 face feeds: 0.05 - 28 mm/rev 60 longitudinal feeds: 0.06 - 56 mm/rev Rapid traverse in longitudinal cross feed Motorized top support Tailstock quill stroke: 280 mm Tailstock taper: MK 6 Space requirement: LxWxH approx. 6700x2500x2250mm Weight: approx. 7500 kg Accessories: 3-axis digital readout HEIDENHAIN Coolant device; chip protection rear panel, power chuck autoblock 500 mm with clamping jaws, roller conveyor cover for lead screw support to bed, machine light, chip conveyor, Parat basic holder incl. 11 holders, suction unit, 3-jaw steady rest with roller inserts (moving), emergency stop, chuck key, moving center point, operating instructions Condition: The machine is in very good technical and optical condition. Backlash in the top slide 0.1 mm and face slide 0.15 mm The geometry of the machine is also very good (was checked with a dial gauge) Measured on the flat track guide with dial gauge in the direction of the lathe chuck Bed wiper replaced, gearbox input shaft axial play compensated and bearings replaced, drive pins on motor/gearbox side replaced, shaft seals on lock case replaced, various bearings replaced The machine can be demonstrated under power. Functional videos can also be sent on request.

Condition: ready for operation (used), Year of construction: 2021, Control Unit Brand SIEMENS Csdpfx Ahexuw Aij Uori Model SINUMERIK 840 D sl Additional Equipment Measuring System: Linear in both axes This 5-axis Pittler PV2500 was manufactured in 2021, featuring a CNC vertical lathe with a maximum swing diameter of 3,000 mm and a turning diameter of 2,800 mm. It includes a double tool holder with Capto C8 interface, high-pressure coolant capabilities, and a robust spindle supporting up to 25,000 kg load. Ideal for complex, large-scale machining tasks. If you are looking to get high-quality turning capabilities consider the Pittler PV2500 machine we have for sale. Contact us for more information. Application Types Turning

Condition: excellent (used), Year of construction: 1983, functionality: fully functional, Weiler Center Lathe Model Condor 81 Lead and Feed Lathe with 3-Axis Digital Readout from K&C NEW Technical Specifications: >> Year of Manufacture 1983 Machine No. 83-067 >> Center height 165 mm >> Center width 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MT 3 >> Feed rates from 0.015 to 0.46 mm/rev >> Possible threads: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be switched on Crjdewb Supjpfx Ah Uoi >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and Equipment: >> New 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating instructions Functions: mm/inch switching, ABS/INC coordinate selection, halving of the display value, reference mark, 200 tool programming, cone calculation, radius/diameter, quick zeroing, counting direction switching >> 1 new three-jaw chuck, 160 mm, 2 sets of jaws >> New collet chuck and new collets from 3 to 26 mm, 1 mm increments >> Multifix size B with 3 tool holders >> Electronic spindle protection >> Rear panel >> Coolant system >> Machine feet About the machine: Offered is a used Weiler Condor 81 in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new 3-axis digital readout from K&C makes work even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was also performed. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to view and try out this machine live on-site.

Condition: good (used), Weiler Condor VS 2 center lathe and feed spindle lathe Crsdpju E H Iwofx Ah Uoi Technical data: Center height 160 mm Center width 800 mm Spindle bore 40 mm Bed width 240 mm Speeds 12 - 2800 min-1 Drive power 3 kW Tailstock holder MK 3 Quill stroke 110 mm Feed rates 0.037 - 1.253 mm/rev Weight, approx. 800 kg Dimensions (WxDxH), approx. 1930 x 880 x 1470 mm Equipment: 3-jaw lathe chuck Quick-change holder system Multifix size A incl. 1 change holder Electrically locked chuck guard Brake motor retrofitted Bed stop Emergency stop button Coolant device Machine light Chip back panel ELESTA 3-axis digital display Moving tip The machine has been technically inspected and is in very good condition. Backlash face spindle 0.2mm Top slide backlash 0.15mm Inspection under power possible at any time. Price net free loading ex warehouse

Condition: ready for operation (used), Year of construction: 2018, Control Unit Brand SIEMENS Codpfx Ahexuw Apj Ueri Model SINUMERIK 840 D sl This 4-axis Pittler PV4000 was manufactured in 2018. A robust vertical turning machine, it features a max swing diameter of 3,800 mm and a spindle load capacity of 35,000 kg. It includes a Siemens SINUMERIK 840 D sl control system, rapid traverse speeds up to 32 m/min, and a tool magazine with 25 positions. Consider the opportunity to buy this Pittler PV4000 vertical turning machine. Contact us for more information about this machine. Application Types Turning

Condition: excellent (used), functionality: fully functional, Weiler Centre Lathe Model Condor 81 Lead and Feed Screw Lathe with 3-Axis Heidenhain Digital Readout Technical Data: Crsdsxu Hlajpfx Ah Uji >> Year of manufacture: 1988 Machine No. 88-955 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 Size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting capability: metric, imperial, module, and diametral pitch >> Metric thread pitches: from 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake can be engaged >> Dimensions: Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis Heidenhain digital readout >> 1 pc. new 3-jaw chuck with 2 sets of jaws >> Collet chuck set, collets from 3 to 30 mm, 40 collets, some duplicate sizes >> Multifix size B with 3 tool holders >> Bed stop >> Machine feet >> Drill chuck >> Live centre For Safety: >> Cover for lead and feed screw >> 2 emergency stop buttons >> Spindle brake About the machine: A used Weiler Condor 81 lathe from 1988 is being offered in very good condition. The machine is of course fully functional. The lead and feed screws are covered for safety. A very robust and powerful machine. The 3-axis Heidenhain digital readout makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A full oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power at our facility.

Condition: ready for operation (used), Year of construction: 2008, General Data Measurements width 2050 mm Measurements depth 2695 mm Measurements height 2120 mm Machine weight 5800 kg Main Drive Csdpfx Ahsxuw Ewo Ujri Spindle motor power 15/15/11 kW Additional Equipment Number of tool stations: 12 (10) Shank height for square tool: 25 mm Boring bar tool shank: Main Spindle: Max 50 mm / Sub-spindle Max: 32 mm Turret switching time: 0.25 s Max speed of driven tools: 6000 rpm Driven Tools and Y-Axis (SY Model): Provides milling and drilling capabilities; allows for off-center milling Bar Feeder and Gantry Loader: With 20-Station Magazine / Dust Extraction System: LTA system / Additional Tank: 500 liters / Knoll Pump: 80 Bar Pressure This 4-axis MORI SEIKI NL 2000 SY /500 turn-mill centre was manufactured in 2008. Ideal for precision machining, it features a robust design and advanced control system. Consider the opportunity to buy this MORI SEIKI NL 2000 SY /500 turn-mill centre. Contact us for more information. Application Types Turning