Condition: used, Single column eccentric press MÜLLER GEFREES type 60 SV DK (identical in construction ExP60) Machine No. 5250686 Year of construction 1986 As good as new condition pressure force 60 ton. throat 280 mm table surface 740 x 560 mm ram area 385 x 200 mm drop-through hole in table 300 x 200 mm table surface intermediate table plate 740 x 560 mm drop-through hole in table intermediate plate Ø 103 mm thickness of intermediate table top 70 mm clamping spigot hole 40 mm Table height above floor 815 mm (with intermediate table top) Installation height max. 275 (with intermediate table top) Installation height max. 345 (without intermediate table top) Stroke adjustment 10-90 mm Plunger adjustment 60 mm Stroke rate 100 strokes/min. Motor power 3 kW drive power 380 Volt, 50 Hz - mechanical rotary wedge clutch with pneumatic control - spring-loaded single-jaw brake controlled via cam disk - stroke release via pneumatic foot switch - overload protection with crushing plate in ram - table height adjustment via 2 threaded spindles Dkjlriei A A Tbjyllol - manual grease central lubrication BEKA Schmiertechnik - Operating instructions and pneumatic diagram available space requirement L x W x H 1400 x 1100 x 2200 mm weight 3,4 ton. very good condition, as new

Condition: good (used), Year of construction: 1987, Functionality: fully functional, throat depth: 180 mm, ram adjustment: 60 mm, total height: 2,000 mm, table width: 360 mm, table length: 560 mm, total width: 950 mm, total length: 1,680 mm, overall weight: 1,750 kg, pressing force: 25 t, Projection 180 mm Smallest distance between press bed and ram at maximum stroke at bottom, Ram adjustment at bottom 50 mm Largest distance between press bed and ram at maximum stroke Dkolriyst Sgruollel top, ram adjustment top 340 mm Fold-through hole in table 150 x 100 mm Table adjustment 150 mm Ram stroke 12-80 mm

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 pressure force 5 ton. throat 125 mm head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination Dkjlriysik Srwellel - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: good (used), Year of construction: 1987, Functionality: fully functional, ram adjustment: 80 mm, total height: 24,100 mm, table width: 600 mm, table length: 800 mm, total width: 18,300 mm, total length: 20,400 mm, overall weight: 4,650 kg, pressing force: 75 t, To be viewed under power. Dsljrr Syboriyllokl

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet Doledzp Tcjriyllekl - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Year of construction: 1965, Condition: good (used), Table area 1,400 x 950 Dolrspwgy Hjiyllekl ram surface 1.000 x 600 ram adjustment 135 mm Stroke 60 - 200, stroke /min. 24

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent Dkeledzqltsriylljl - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: good (used), Year of construction: 2004, Functionality: fully functional, table width: 610 mm, table length: 850 mm, installation height: 300 mm, total width: 19,000 mm, total length: 19,000 mm, overall weight: 8,500 kg, pressing force: 120 t, power: 12 kW (16.32 HP), can be viewed on site under power Doljrwl Eroriyllskl

Condition: used, Double column eccentric punching press BLEMA Gotha type PEZ 160-50 MHSY-ES Eccentric press with roller feed ALBA Machine no. No. 88151005 Year of construction 1988 / 92 Pressure force 160 ton. Frame width 970 mm Stand width sideways 560 mm Table size 900 x 900 mm ram surface 900 x 700 mm Tool installation height 560 mm, max. 700 mm Stroke adjustment 8-160 mm Ram adjustment travel 125 mm Stroke rate 25 to 70 strokes/min. Belt width in roller feed max. 400 mm Motor power approx. 15 kW Mains connection 380 Volt, 50 Hz - Infinitely variable stroke rate via frequency control - Automatic stroke adjustment - ram weight compensation cylinder with compressed air - Hydraulic overload protection in the ram - Pneumatic clutch/brake combination - Central oil lubrication - Precisely guided press ram with oil-lubricated guides - UNIDOR press control - Swiveling control panel - Press and feed control cabinets, together on one platform, adjacent Platform dimensions 3400 x 2250 mm, height without feet 2950 mm Width of the press without feed 2100 mm Depth of the press with drive motor 2300 mm Overall height of the press 4150 mm Weight of punching press approx. 18 tons. For transportation, the drive motor is removed and the machine is placed on its face. In addition: NC roll feed straightening machine ALBA type GGVHY400 Apparatus no. 1405 and 1406, order no. 910708 (year of manufacture 1992) - ALBA PSS 300 feed control - Feed length infinitely programmable from 0.1 to 6500 mm per stroke - Belt thickness at 400 mm width max. 3 mm Dkslodzqlveriylljl - Belt thickness for 300 mm width max. 4 mm - Belt cross-section max. 1200 mm2 - Roller drive hydraulically controlled by the feed - Height-adjustable feed unit on the press to adjust the material infeed height - Hydraulic unit opposite - Drag straightener with hydraulic opening and closing Weight of the complete system approx. 24 tons Space required for transport a mega trailer with an internal height of 3 meters and a loading length of 13.6 meters good condition

Condition: good (used), Year of construction: 2001, Table 950x650 mm, ram 610x410 mm, stroke 0-140 mm Dkslriyjqgcaasllol

Condition: used, Double column hydraulic press ALPHA TEC -- ALPHATEC type RPS 5000 fabric. no. 300487 year of construction 2006 pressure force 500 ton. stand width front and rear 2520 mm table area 2500 x 2500 mm Dkslredzqptjiylljl ram surface 2500 x 2500 mm ram stroke 600 mm installation height max. 600 mm Table height above floor approx. 900 mm tank capacity approx. 1000 liters ram retraction force approx. 22 ton. Feed speed adjustable 100-800 mm/s pressure build-up to 5000 kN approx. 0,7 sec. return stroke speed approx. 300 mm/s Motor power main motor 75 kW Motor power control pump 2,2 kW Mains connection 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking at TDC - adjacent control cabinet (200 x 50 cm) - Electrical control SIEMENS SPS S7-314 - Operation via SIEMENS OP 170-B (5,7") - 2-hand control panel adjacent - ground level installation - table top 2510 x 2530 x 135 mm (approx. 6700kg) - central lubrication - operating instructions with circuit diagrams space requirement L x W x H 372 x 260 x 460 cm Space requirement for horizontal transport L x W x H 460 x 372 x 260 cm Weight approx. 50 ton. The machine was used for straightening of red-hot steel flanges. From insolvency - in good condition

Year of construction: 1963, Condition: excellent (used), Force 150tons Throat 550mm Daylight 500mm Table size 1200x1000mm Ram size 1200x800mm Stroke 10-140mm Strokes 40 Dkelefc Dqujriyllel requested power 15 PS Weight 12000Kg Height 3000mm Width 1400mm Depth 3000mm motorized ram adjustment

Condition: used, Pneumatic press, compressed air press BOSCH Type No. 041 Year of manufacture 1980 Djlriyoh U Dtusllskl Compressive force 18 KN = 1.8 tons at 5 bar 15 kN = 1.5 ton. at 4 bar 12 kN = 1.2 ton. at 3 bar 8 kN = 0.8 ton. at 2 bar 6 kN = 0.6 ton. at 1.8 bar Projection 100 mm Plunger stroke 70 mm Table surface 245 x 200 Plunger surface Ø 45 mm Installation height max. 235 mm Clamping pin bore Ø 20 mm with clamping screw Compressed air requirement 5 bar - Pressing force infinitely adjustable via pressure regulator - Pneumatic cylinder with ram height-adjustable by 90 mm - Pneumatic 2-hand operation - Mounted on metal base frame with wooden plates Space requirement L x W x H 1050 x 700 x 1600 mm Weight of pneumatic press 82 kg Weight with table base 140 kg good condition

Condition: good (used), Year of construction: 2002, Functionality: fully functional, table width: 610 mm, table length: 850 mm, installation height: 300 mm, total width: 19,000 mm, total length: 19,000 mm, overall weight: 8,500 kg, pressing force: 120 t, power: 12 kW (16.32 HP), to visit under power Dkslrijrwlxtoyllol

Condition: used, Single column hydraulic press MAE type S63SZ SO . 551277 Year of construction approx. 1977 Dkeledzp Trjriyllsl Pressure force 63 ton. Throat 320 mm Table surface 850 x 630 mm ram surface 1050 x 500 mm Plunger stroke 500 mm Installation height max. approx. 730 mm Table height above floor 970 mm Hydraulic tank capacity 600 litres Drive power 15 kW Power supply 380 Volt, 50 Hz - Hydraulic drawing cushion under the table with holes through the table top - 2-hand control - Electrical control cabinet damaged Space requirement L x W x H 2000 x 1200 x 3420 mm Weight approx. 5 ton. The machine is working, the switch cabinet is mechanically damaged. During the test run, the machine reaches a press force of 50 tons, presumably a pressure relief valve is escaping.

Year of construction: 1988, Condition: good (used), Force: 160 tons Windows: 600mm Daylight: 750mm Dkslried Rlm Reyllol Table: 1400x900mm Ram 1400x900mm Speed down 400mm/sec. up 300mm/sec. work 19-50mm/sec. Stroke: 400mm Requested power: 45 KW Weight 23 tons Height: 4300mm Machine is floorstanding Siemens S5 control 3 cushions in bed

Condition: used, Hydr. spotting press MILLUTENSIL type BV 25 PM Machine. No. 632 / 25111 Year of construction 1991 Closing force 18 ton. Opening force 15 ton. Table surface 775 x 760 mm Clamping surface of the upper table 900 x 550 mm Frame width 900 mm Installation height max. 750 mm Dkjlriotx E Rdsyllel Installation height min. 230 mm Stroke of the upper table 520 mm Lifting speed infinitely variable 0 - 1000 mm/min. Hydraulic pressure adjustable 10 - 200 bar Tool weight on the table max. 2500 kg Tool weight on the upper table max. 800 kg Table height above floor 850 mm Motor power 4 kW Mains connection 380 Volt, 50 Hz - Upper table can be swiveled 360° by motor - Hydraulic ejector unit in the table with 120 mm stroke - M 14 threaded holes in the table - Hydraulically extendable table - Depth adjustment bar for automatic downward stroke limitation Space requirement L x W x H 1550 x 1500 x 2000 mm Weight 1900 kg

Condition: good (used), Year of construction: 2000, total height: 47,000 mm, total width: 27,000 mm, total length: 25,000 mm, table width: 1,000 mm, table length: 1,800 mm, overall weight: 43,000 kg, ram plate width: 600 mm, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Light barrier Sick Separate control cabinet Ritta Dksletiwgijriylljl Side passages Ground level installation

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm Djlstx E Rqeriyllokl ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Year of construction: 1993, Force: 100 tons Delsc Uwx Deriyllokl Max. distance between columns: 1400mm Stroke: 250 mm Windows: 400mm Daylight: 400mm Table: 1250x1100mm Ram: 1250x1100mm Speed fast down: 400mm/sec. fast uo: 330mm/sec. work: 24-43 mm/sec. Power: 33kW Weight: 10.000 kilos Height: 3300mm Width: 1700mm Depth: 1800mm 2-Hand operation Cutting dampers

Condition: used, Single-column eccentric press AMBOLD type PEEV 25.2 Machine. No. 11734 / 02 Year of construction 2002 Pressure force 25 ton. throat depth 200 mm Table surface 520 x 400 mm Plunger surface 155 x 155 mm Drop-through hole in table 185 x 155 mm Stroke adjustment 4-80 mm Plunger adjustment range 40 mm Installation height max. 270 (maximum stroke in UT, table at bottom) Dolriystx E N Tellekl Clamping pin bore Ø 32 mm Table height adjustment approx. 150 mm Ram strokes 160 strokes/min. Motor power 2.2 kW Mains connection 400 Volt, 50 Hz - Pneumatic clutch/brake combination ORTLINGHAUS - HERION press safety valve - PILZ press control - electric foot switch and two-hand operation - height-adjustable press table via 2 threaded spindles - Automatic central grease lubrication VOGEL - UVV according to VBG 7n 5.1 for manual insertion work - Control cabinet opposite L x W x H = 600 x 310 x 1500 mm Space requirement L x W x H 1450 x 1000 x 1850 mm Weight 1.9 ton. very good condition

Condition: excellent (used), Year of construction: 1990, Force 25tons Throat 160mm Daylight 500mm Table size 650x650mm Ram size round 140mm Stroke 130mm requested power 4 KW Weight 2000Kg Dkeljfcw Aporiyllol height 2100mm width 1100mm depth 1500mm

Condition: used, Double column hydraulic press RASTER ZEULENRODA (WALTER) type WUP S 60 Machine. No. 136 / 7 (156-165) Year of construction 1999 Basic machine built in 1987, completely overhauled in 1999 with new control system Pressure capacity 60 ton. Stand width 1090 mm Lateral column passage 265 mm (one-sided) Ram area 650 x 300 mm Additional plate on ram 990 x 550 x 60 mm Table surface 990 x 550 mm Plunger stroke max. 320 mm Installation height 330 or 390 mm Table height above floor 980 mm Hydraulic operating pressure 320 bar Rapid traverse downwards 75 mm/s Rapid traverse upwards 100 mm/s Working speed 17 mm/s Return speed 33 mm/s Motor power 15 kW (2x 7.5 KW) Mains connection 400 Volt, 50 Hz, 15.5 kW - Press safety control PILZ PSS 3056-1 + PXT 305 Com-LC - Manually adjustable limit switch cams for stroke limitation - 2-hand operation and electric foot switch - Press force adjustment via handwheel - ram plate additionally guided by 2 lateral guide rods, Ø 50 mm - Table top with 18 mm T-slots, slot spacing 175 mm - Through-hole table top Ø 100 with insert reduction to Ø 30 mm - Plunger plate with 18 mm T-slots, slot spacing 150 mm - Additional ram plate without fastening grooves - Electrical cabinet on the side of the machine stand - Electrical circuit diagram Dkelriysuicg Uelljl - 2 monitored safety valves for the hydraulics - UVV for manual insertion work Space requirement L x W x H 1950 x 1000 x 2700 mm Weight 2.6 tons good condition

Condition: excellent (used), Year of construction: 1988, Force: 125 tons Windows: yes Daylight: 380mm Table: 1100x700mm Ram: 700x350mm Stroke: 01-120mm Strokes per Minute: Approx. 70 Requested power: 22kW Weight: 8500kg Doljdvb Tforiylljkl Height: 2900mm

Condition: excellent (used), Year of construction: 1983, Force: 45 tons Daylight: 205/305mm Table: 700x450mm Ram: 700x360mm Ram adjustment: 50mm Stroke: 10 - 50mm Strokes per minute: 80-400 Requested power: 11 kW Dkolriylsgfvnnjljl Weight: 7.200 kos. Height: 3.100mm